UCC2813QDR-5Q1
Product Specifications
UCC2813QDR-5Q1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC2813QDR-5Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC2813QDR-5Q1: the automotive member with a 4 V reference and a 4.1 V lockout
The UCC2813QDR-5Q1 is the automotive qualified version of the -5 member of the UCCx813-x family. Two things separate it from the industrial codes: a 4 V reference rather than 5 V, and a lockout that turns on at 4.1 V and off at 3.6 V, which suits a converter biased from a 5 V rail in a vehicle rather than from an off line start up circuit. Maximum duty is about 50 percent through the toggle latch, start up current is 100 microamps, run current is 500 microamps, and the 1 A totem pole output drives a MOSFET gate directly with 70 ns from current sense to output.
A 4 V reference changes the feedback arithmetic in a way that catches people out. The error amplifier input sits at half the reference, so it is 2 V rather than 2.5 V, and a divider copied from a 5 V part produces an output about 20 percent low. The lower reference also keeps the internal circuitry in regulation when the bias rail is only slightly above the lockout, which is the reason the vendor offers the 4 V option at all: a 3.3 V or 5 V automotive rail has less headroom than a mains derived bias, and a 5 V reference needs more of it.
Key electrical data for the UCC2813QDR-5Q1
| Supply | Start up 100 microamps typical, run current 500 microamps typical, operation to 1 MHz |
| Lockout | Turn on 4.1 V, turn off 3.6 V, the low window option in the family |
| Reference | 4 V output, error amplifier input at 2 V, which needs a different divider from the 5 V members |
| Output | 1 A totem pole, actively held low while the supply is below the lockout |
| Timing | 70 ns typical from the current sense input to the gate drive output |
| Duty | About 50 percent maximum through the toggle latch |
Package, marking and reel data
| Body | D, SOIC 8 pin, automotive qualified, ambient range minus 40 C to 125 C |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier, quadrant Q1 |
| Finish | NIPDAU in the addendum rows, with the quantity column left blank on the -4 and -5 rows |
| Family | The same silicon is offered as UCC2813QDR-0Q1 through -5Q1 and as a TSSOP body on the -3 member |
The blank quantity column is the detail to check first
The vendor addendum prints a quantity for the -0, -1, -2 and -3 rows of this family but leaves the quantity column empty for the -4 and -5 rows, and the tape and reel drawing for those rows carries the carrier dimensions without a piece count. That does not mean the reel is short, it means the figure is unpublished on that row, so a material requirement plan built from the addendum alone will show an unknown. For an automotive build the reel count is part of the traceability record, and the answer has to come from the packing list or from the vendor directly. Our kitting service page covers how we reconcile reel counts against a bill of materials before a build starts.
The other automotive detail is the range of the reference over temperature. A 4 V reference at 1.5 percent tolerance is plus or minus 60 mV, and the error amplifier input follows it, so a 3.3 V output divider has to be sized with that window in the tolerance stack. Where the load is an automotive sensor that expects 3.3 V plus or minus 2 percent, the controller reference alone eats most of the budget, and a post regulator or a trimmed reference is the answer rather than a tighter resistor pair.
Buyer questions on the UCC2813QDR-5Q1
Does the -5 member work on a 12 V automotive rail? It runs, but its lockout is 4.1 V, so the part is aimed at a 5 V bias rather than at a 12 V rail that has to ride through a cold crank. The -2 and -4 members carry the higher window.
Can a divider from a 5 V member be reused? Not directly. The reference drops from 5 V to 4 V, so the same divider gives a lower output. Recalculate from the 2 V error amplifier input.
Is the 50 percent duty limit a problem for a flyback? It is for a wide input flyback that needs more than half a cycle. This member suits a push pull or a half bridge arrangement where the limit is part of the topology.
Availability and cross reference
The automotive rows carry the Q1 suffix and a 125 C ambient rating, and the industrial UCC2813DTR-5 row carries 85 C with the same reference and lockout. A build that starts on the industrial part and later needs the automotive grade keeps the same footprint and the same divider, so the change is a qualification step rather than a board change. We hold both grades and record which one went into each lot, and the traceability route is described on our sourcing audit trail page.