UCC2813DTR-4
Product Specifications
UCC2813DTR-4
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC2813DTR-4 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC2813DTR-4: an economy current mode controller for an off line bias rail, with the highest lockout in its family
The UCC2813DTR-4 is a BiCMOS current mode pulse width modulator in an eight pin SOIC, one of the six members of the UCCx813-x family. The -4 suffix sets two things: a 5 V reference, and an undervoltage lockout that turns on at 12.5 V and off at 8.3 V, which is the widest hysteresis in the family and the reason the vendor points this member at off line supplies. Start up current is 100 microamps typical, run current is 500 microamps, and the output is a 1 A totem pole stage that drives a MOSFET gate directly. The current sense to output delay is 70 ns typical, which is what keeps a peak current mode loop from overshooting on a short circuit.
What the part adds over the UC3842 family it replaces is internal: a full cycle soft start, leading edge blanking on the current sense input, and a trimmed reference good to 1.5 percent. Leading edge blanking is the detail that removes the filter network most UC3842 circuits carry between the sense resistor and the CS pin, because the first tens of nanoseconds after the gate turns on are ignored by the controller instead of being filtered by an RC. The -4 and the -1 limit maximum duty to about 50 percent through a toggle latch, while the -0, -2 and -3 members reach 99 percent, so a push pull or a half bridge stage takes the -4 and a flyback takes one of the others.
Key electrical data for the UCC2813DTR-4
| Supply | Start up current 100 microamps typical, run current 500 microamps typical, operation to 1 MHz |
| Lockout | Turn on 12.5 V, turn off 8.3 V, which is 4.3 V of hysteresis |
| Reference | 5 V output inside 1.5 percent, one half of it feeds the error amplifier as 2.5 V |
| Output | 1 A totem pole gate drive, actively held low while the supply is below the lockout |
| Timing | 70 ns typical from the current sense input to the gate drive output |
| Duty | About 50 percent maximum through the toggle latch on the -1 and -4 members |
Package, marking and reel data
| Body | D, SOIC 8 pin, the same pinout as the UC3842 and the UCC3802 families |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier, quadrant Q1 |
| Finish | NIPDAU, moisture level 1 at 260 C with unlimited floor life on the taped row |
| Grade | UCC2813 is specified from minus 40 C to 85 C, the UCC3813 sibling from 0 C to 70 C |
Why the lockout window decides the member, not the reference
A controller that turns on at 12.5 V and off at 8.3 V can be biased from an auxiliary winding that only comes up after the converter has started, because the 4.3 V of hysteresis keeps the part running while the winding voltage sags under a load step. A part with a 4.1 V lockout cannot do that on a 12 V rail, and a part with the 5 V reference but a narrow window is worse than useless in the same position. The table in the datasheet lists all six combinations, and the two variables are independent: the reference decides the error amplifier's input range, the lockout decides the bias arrangement, and the duty limit decides the topology.
The reference is 5 V on this member and 4 V on the -3 and -5, which matters when the same board is used for a battery product and a mains product. A 4 V reference with 2 V at the error amplifier input gives a lower feedback divider ratio and more headroom at a 3.3 V output, and it also lets the reference stay in regulation when the bias rail is only 5 V. Our power management cross reference page lists the members of this family and the codes that share the pinout.
Buyer questions on the UCC2813DTR-4
Can the part replace a UC3842 without a board change? The pinout is the same, and the vendor states the part as a replacement. The differences are internal soft start and leading edge blanking, so an existing RC filter on the sense line becomes optional rather than required.
What limits the duty cycle to 50 percent? A toggle latch inside the device on the -1 and -4 members. The other members pass the full duty range, so a flyback that needs 80 percent duty takes a different suffix.
Is a 100 microamp start up current useful in practice? It is when the bias comes from a resistor off a high voltage rail. The resistor can then be large enough to dissipate little while the part is off, and the auxiliary winding takes over once the converter runs.
Availability and cross reference
The taped row is 2500 pieces and the family shares one body and one pinout, so a change of suffix is a change of behaviour rather than of footprint. Two of the reel rows print 2000 pieces and the rest print 2500, which is worth knowing before a line is scheduled around a reel count. We keep the 5 V and 4 V members separately because a feedback divider built for one does not transfer to the other, and the check we run before offering a substitute is on our how to verify a drop in replacement page.