UCC2808DTR-2
Product Specifications
UCC2808DTR-2
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC2808DTR-2 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC2808DTR-2: a push pull controller that keeps its lockout low enough for a 5 V bias rail
The UCC2808DTR-2 is the low lockout member of the UCCx808 family, a current mode push pull pulse width modulator in an eight pin body. The turn on threshold is 4.3 V and the turn off threshold is 4.1 V, against 12.5 V and 8.3 V on the -1 member, so the -2 suits a converter biased from a 5 V housekeeping rail while the -1 suits an off line stage that charges its own bias capacitor from a high voltage start up resistor. Both outputs switch at half the oscillator frequency through a toggle flip flop, and the dead time between them runs from 60 ns to 200 ns depending on the timing components, which keeps each output below 50 percent duty.
The part carries a full control set in eight pins: an error amplifier with a 2 MHz gain bandwidth product, an internal soft start, an internal VDD clamp, and a start up current of 130 microamps against a run current of 1 mA. Operation to 1 MHz is specified, and the output stages deliver 500 mA peak source and 1 A peak sink, which is enough to drive a pair of small MOSFETs directly or to drive a larger pair through a buffer. The VDD clamp means the bias can be fed from a resistor off the high voltage rail without an external zener, which is the arrangement the vendor shows in its application circuit.
Key electrical data for the UCC2808DTR-2
| Lockout | Turn on 4.3 V, turn off 4.1 V, the low level option in the family table |
| Currents | 130 microamps typical starting current, 1 mA typical run current |
| Outputs | Dual push pull stages, 500 mA peak source and 1 A peak sink, dead time 60 ns to 200 ns |
| Oscillator | Operation to 1 MHz, frequency set by the timing resistor and capacitor |
| Amplifier | On chip error amplifier with 2 MHz gain bandwidth product |
| Protection | Internal soft start, on chip VDD clamping, cycle by cycle current limit through the CS pin |
Package, marking and reel data
| Body | D, SOIC 8 pin, ambient rating minus 40 C to 85 C on this row |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier, quadrant Q1 |
| Finish | The plain UCC2808DTR-2 row prints Call TI for lead finish and marking, the .A row prints NIPDAU at level 1 |
| Marking | The .A row carries the marking field, which is what a receiving inspection check has to match |
Reading the addendum before a first order
The plain and .A rows of this code are not the same document. The plain row shows production status with lead finish and marking both reading Call TI, while the .A row is active with NIPDAU at moisture level 1 unlimited. On a build that has to be traceable, the suffix in the .A row is the string to order, because the marking and the finish are the two fields a receiving inspection can actually verify against the label. The same family also contains codes where the quantity column is blank, and a blank quantity is not a reel size of zero, it is a figure the vendor has not published on that row.
The other check is the bias arrangement. A -2 member on a 12 V housekeeping rail sits only 7.7 V above its turn on threshold, which is fine, but a -2 member fed from a resistor off a 400 V rail through a 5 V clamp draws its start up current from that resistor, so the resistor has to be sized for 130 microamps and the clamp has to dissipate the difference. Where the bias comes up slowly the internal soft start covers the first cycles and the error amplifier settles without a transformer walk. Our date code management page covers how we hold and label these parts between builds.
Buyer questions on the UCC2808DTR-2
What is the difference between the -1 and the -2? Only the lockout level. The -1 turns on at 12.5 V and off at 8.3 V, the -2 at 4.3 V and 4.1 V. The rest of the electrical set is shared, and the pinout is the same.
Can the outputs be paralleled for more drive? No. The two outputs are a push pull pair driven by a flip flop, so they are never on together by construction. More drive current needs a buffer or a different driver part.
Does the internal clamp replace an external zener? It replaces it on a current limited bias source. The vendor warns that the clamp does not protect the device from an unregulated supply, so a resistor or a current limit is still required.
Availability and cross reference
This code is published at 2500 pieces on a large reel and the family shares the SOIC 8 body across all four members, so a change from the low lockout part to the high lockout one does not need a board change but does need a bias check. We hold both lockout options because customers move between a 5 V housekeeping rail and a high voltage start up circuit during a product's life, and the substitution check is on our how to verify a drop in replacement page.