Contact Us

UCC28086DR

Brand: Texas Instruments
Texas Instruments UCC28086DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28086DR — Power Management & Signal Chain | Superb Automation

UCC28086DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28086DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28086DR: an eight pin push pull controller with programmable slope compensation and a 4.3 V lockout

The UCC28086DR is a current mode push pull controller in an eight pin body, one member of the UCC28083 to UCC28086 family. Both outputs switch at half the oscillator frequency through a toggle flip flop, and the dead time between them is 110 ns typical, which limits each output to less than 50 percent duty and prevents the two halves of a push pull transformer from conducting at the same time. The oscillator is set by a single resistor and capacitor pair from 50 kHz to 1 MHz, and the current sense signal carries a programmable slope ramp injected through the ISET pin so a peak current mode loop stays stable above 50 percent duty.

This member is the one without an internal soft start and without an error amplifier. The control input is CTRL, a direct threshold that the loop drives, and the CS pin has an internal discharge transistor that pulls the sense node down at the end of each cycle to improve the dynamic response after a large step. The lockout level is 4.3 V on and 4.1 V off, which suits a 5 V bias rail rather than a 12 V one, and the sibling codes with a 12.5 V lockout cover off line bias arrangements. Start up current is 120 microamps and the run current is 1.5 mA.

Key electrical data for the UCC28086DR

SupplyVDD to 15 V absolute, UVLO turns on at 4.3 V and off at 4.1 V on this member
Currents120 microamps typical start up, 1.5 mA typical run, 2.5 mA maximum
OutputsDual totem pole, 0.5 A source and 1 A sink, push pull arrangement, 110 ns dead time
Oscillator50 kHz to 1 MHz programmed by one resistor and one capacitor, timing resistor 25 k to 698 k
SlopeProgrammable ramp added to the CS signal, set by the resistor from ISET to ground
ProtectionCycle by cycle current limiting with the CS discharge transistor active at the end of each cycle

Package, marking and reel data

BodyD, SOIC 8 pin, marking 28086, ambient rating minus 40 C to 85 C
Reel2500 pieces on a 330 mm reel, 12.4 mm carrier on the rows that print a quantity
FinishNIPDAU on the .A row at moisture level 1 unlimited, level 2 with a one year floor life on the plain row
StatusUCC28086D prints NRND, UCC28086DR prints active with the quantity column left blank for Call TI

Slope compensation is the reason to take this part

Peak current mode control in a push pull stage becomes unstable as duty rises, because the inductor current slope that the comparator sees is too shallow to resist a perturbation. The usual cure is a resistor from the timing node into the sense line, which couples the oscillator ramp into the current signal. This family replaces that network with a transconductance stage inside the device: a resistor from ISET to ground sets the ramp amplitude, and the ramp is summed with the CS signal before the comparator. The result is a stable loop at duty cycles where the passive network would have forced a larger sense resistor and therefore more loss.

The internal discharge transistor on CS matters in the same context. At the end of each switching cycle the sense node is pulled down instead of being allowed to decay through the filter network, so the next cycle starts from a known level and a load step is answered in one cycle rather than three. Where a product needs a soft start ramp, it has to be built externally on this member because the internal soft start belongs to the 803 and 804 codes. Our pin to pin cross reference page lists the codes in this family and which of them carry the soft start and the error amplifier.

Buyer questions on the UCC28086DR

Why is the lockout only 4.3 V? The part is aimed at systems biased from a 5 V rail. For a 12 V bias a member with the 12.5 V lockout is the correct code, and the pinout does not change.

Is there an error amplifier inside? No. The control input is CTRL and the loop compensation is external. A product that needs the internal amplifier takes the UCC28083 or UCC28084 instead.

What does the NRND status on the D row mean? It means not recommended for new builds on that specific row, while the DR row prints active. For a new production release we confirm the row and the status in writing before quoting.

Availability and cross reference

The addendum for this family is mixed: some rows print active, some print NRND and one prints obsolete, and the quantity column is missing on several active rows. That is a part where the status has to be read per row rather than per family, because a customer who approves the family and orders a specific suffix can end up with a different answer. We record the row and its status against every shipment, and the long term plan for a part in this position is set out on our last time buy and LTB planning page.