Contact Us

UCC28064ADR

Brand: Texas Instruments
Texas Instruments UCC28064ADR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28064ADR — Power Management & Signal Chain | Superb Automation

UCC28064ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28064ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28064ADR: a two phase interleaved transition mode power factor correction controller with burst mode, adjustable phase shedding and sensorless current shaping, in the sixteen pin SOIC on a 2500 piece reel

UCC28064ADR is a power factor correction controller that runs two boost stages out of phase so the input ripple and the bulk capacitor current cancel, and that drops to a single phase and then to burst mode as the load falls, without a current sense resistor on either phase in a SOIC body of 16 pins. The D body is 9.90 mm by 3.91 mm with sixteen pins, and the sixteen pin count is what gives the two gate drives, two zero crossing inputs and the phase management pins their own terminals.

Order code and package

Catalogue stringUCC28064ADR, where 064A is the revision with the light load burst behaviour, D is the sixteen pin SOIC and R is the large reel
BodySOIC, D outline, sixteen pins, 9.90 mm by 3.91 mm
Reel2500 pieces on a 330 mm reel, printed identically on the plain, .A and .B rows of the addendum
StatusActive in production, with the plain row, the .A row and the .B row all shipping the same quantity
Finish and moistureCU NIPDAU with a Green declaration for RoHS and no antimony or bromine, at moisture level 1 for 260 C with no floor life limit
Temperatureminus 40 to 125 C on the addendum and in the electrical table, which is the range the part is signed off over rather than a marketing figure
Topologyinterleaved transition mode, two channels both acting as masters with no slave channel, synchronised to one frequency
DocumentSLUSC60B, December 2017, revised October 2019

Electrical parameters that decide the application

Bias rangeVCC turns on between 9.45 V and 11.1 V, typically 10.35 V, and turns off between 8.8 V and 10.7 V, typically 9.6 V, with 0.8 V of hysteresis
Bias current125 to 200 microamps below the lockout, 150 to 210 microamps while disabled, 650 to 850 microamps in burst mode with no switching, and 5 to 8 mA while running
Reference5.82 V minimum, 6.00 V typical and 6.18 V maximum with no load, and the output sense regulation point is the same 6.00 V, so the feedback divider is built against one number
Output sense5.82 to 6.18 V over temperature, with 50 to 150 nA of input bias current, which is low enough for a high value divider to be used without an offset error
Error amplifier55 microsiemens of transconductance in the small signal region and 290 microsiemens in the large signal region, with the COMP pin clamped at 4.95 V
Over voltagethe first threshold sits 8 per cent above the regulation point and the second 11 per cent above it, and the separate HVSEN comparator trips at 4.87 V rising and 4.67 V falling
Current limitminus 0.2 V on CS in two phase operation and minus 0.166 V in single phase, so the limit tightens automatically when the second phase is shed
Current limit timing60 ns from the CS pin crossing the threshold to the gate falling, with 100 ns of blanking on both the rising and the falling edge
Zero crossingthe ZCD pin triggers at 1.0 V falling and re-arms at 1.7 V rising, clamped at 3 V, with 100 ns of blanking and a 50 ns delay to the gate
On timethe maximum FET on time is 20.4 microseconds at the low line condition and 2.0 microseconds at the high line condition, so the controller shortens the pulse rather than the frequency at the top of the range
Minimum period2.7 microseconds with RTSET at 133 k, which is the floor that sets the maximum switching frequency at the peak of the line cycle
Brownoutthe VINAC brownout threshold is 1.45 V, with a 640 ms filter before the controller stops and a 450 ms reset time, and a separate dropout detector at 0.35 V with a 5 ms filter
Gate drive12.4 V typical at 100 mA of sink, 18 ns rise and 12 ns fall into 1 nF, with a gate voltage that follows VCC below the regulation point
Thermalthe junction shuts down at 160 C and restarts at 140 C, which is above the specified operating range and therefore a protection limit rather than an operating point

Family variants and how they differ

Phase managementthe PHB pin sets the load at which the second phase is shed, with 150 mV of hysteresis on COMP, and the sourced current is 2 to 4.1 microamps when the input is high
Burst modethe BRST pin sets the burst threshold with 50 mV of hysteresis, and burst mode removes the need for an auxiliary flyback to meet standby power targets
Sensorless current shapingthe controller reconstructs the inductor current from the on time and the input voltage, so there is no shunt in the power path and no current sense winding on the boost inductor
Inrush behaviourthe gate drive is held off while the output is below the input, which prevents the boost FET from conducting during inrush and avoids reverse recovery in the output rectifier
Companion partsthe vendor pairs this controller with the UCC25630x LLC controller and the UCC24624 synchronous rectifier controller for a two stage adapter
Single phase operationin single phase the on time factor changes from 4.15 to 8.3 microseconds per volt at low line, so the compensation and the inductor value cannot be copied unchanged from a two phase stage
Package siblingsthe same controller in a different body carries a different reel size, so a line change from SOIC to a smaller outline also changes the packing quantity

Points to check before this part goes on a BOM

Interleaving is the reason to use this part rather than a single phase controller at the same power. Two stages 180 degrees apart cancel most of the input ripple current, which cuts the differential mode filter and the bulk capacitor ripple rating, and the data sheet puts a 600 W stage on a single pair of inductors rather than on a larger single stage.

The current limit threshold changes when the second phase is shed, from minus 0.2 V to minus 0.166 V. A board that is qualified at full load and then tested at light load sees a limit that is 17 per cent lower, and a marginal inductor saturation margin can turn into a current limit hiccup at exactly the load where nobody is looking.

The on time factor is given at two input voltages and for two modes, four numbers in total, and they are not proportional. At low line in two phase operation the factor is 4.15 microseconds per volt and at high line it is 0.43, which is why the compensation network has to be checked at both ends of the input range rather than only at nominal.

Brownout behaviour is filtered rather than instantaneous: 640 ms below the threshold before the controller stops and 450 ms above it before it restarts. On a generator or a weak mains feed that dips for a few hundred milliseconds, the controller keeps running and the hold up capacitor has to cover the dip, which is a different requirement from a controller that reacts within one cycle.

The burst threshold and the phase shedding threshold are both set by resistors and both have hysteresis of their own, 50 mV and 150 mV on COMP. Setting them too close together produces a mode that oscillates between single phase and burst at a fixed load, which shows up as a low frequency ripple on the output rather than as a fault.

HVSEN is a separate over voltage input at 4.87 V and it is not the same comparator as the 8 per cent output sense threshold. A divider built for the output sense does not protect the downstream stage, and the two have to be set independently.

What the sixteen pins carry

Two gate drives, GDA and GDB, each able to sink 100 mA at 12.4 V and rise in 18 ns. Two zero crossing inputs, one per phase, each with its own blanking and clamp. VINAC for the brownout and the line feed forward, VSENSE for the output divider, HVSEN for the independent over voltage, and COMP for the loop.

The remaining pins are the two threshold setting pins, PHB for phase management and BRST for burst, the timing resistor RTSET, and the bias and ground pair. Nothing on the part needs an external oscillator, and nothing needs a current sense input from the power path.

Where this order code fits

Two stage AC to DC adapters in the 300 W to 600 W class, television and monitor supplies, all in one computers, gaming and home audio power, and any offline front end that has to hold standby power below the one watt class limits without a second converter Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Does it need a current sense resistor? No. The controller reconstructs the inductor current from the on time and the input voltage, and the CS pin is used for the over current comparator only, at minus 0.2 V in two phase mode.

What happens at light load? The second phase is shed at a COMP level set by the PHB resistor, and below the BRST threshold the part enters burst mode, drawing 650 to 850 microamps with no switching.

Can it run from a 12 V bias? Yes. The turn on threshold is 10.35 V typical and the turn off 9.6 V, so a 12 V rail starts it, but the rail has to stay above 9.6 V through any dip or the part restarts.

Why is the reference 6 V rather than 2.5 V? A high reference lets the output divider pass a smaller current and keeps the divider ratio closer to unity at 400 V, which reduces the leakage path from the high voltage rail to ground.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.