Contact Us

UCC28056DBVR

Brand: Texas Instruments
Texas Instruments UCC28056DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28056DBVR — Power Management & Signal Chain | Superb Automation

UCC28056DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28056DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28056DBVR: six pin transition mode power factor controller

UCC28056DBVR is a single phase transition mode power factor correction controller in a SOT-23 body of 6 pins. It is a six pin controller that keeps a boost stage in transition mode and switches the FET on at the drain valley, so the boost inductor needs no second winding. The no load input power stays under 80 mW at 230 V AC in a PFC plus LLC system, and the supply range is 8.5 V to 34 V.

Order code and package

UCC28056DBVRDBV body, SOT-23-6, 3000 pieces on a large reel
UCC28056DBVTthe same body at 250 pieces on a small reel
UCC28056BDBVR and CDBVRthe B and C revisions are separate rows in the same addendum at 3000 piece packing
UCC28056ADBVTthe A revision at 250 pieces, listed beside the G4 row

Electrical parameters that decide the application

Supply range8.5 V to 34 V on VCC
Startup currentbelow 46 uA
Standby powerunder 80 mW at 230 V AC in a PFC plus LLC system
Controltransition mode with multi-mode operation at light load, valley synchronised turn on
Valley delayuser adjustable through an external component
Protectioncycle by cycle current limit, a second independent output over voltage comparator, over temperature protection
Burst modesoft entry and soft exit periods to keep the audible noise down
PackageSOT-23-6, 3000 or 250 piece packing

Family variants and how they differ

Plain stringUCC28056DBVR and DBVT, the base revision
A revisionUCC28056ADBVR and ADBVT, 250 piece small reel rows in the same addendum
B revisionUCC28056BDBVR and BDBVT, 3000 and 250 piece packing
C revisionUCC28056CDBVR and CDBVT, the newest rows in the addendum

Points to check before this part goes on a BOM

Valley synchronised turn on is what removes the second winding on the boost inductor. The controller watches the drain voltage through the feedback divider and switches when the drain has fallen to the valley, so the turn on loss drops without an auxiliary winding to sense the inductor current zero crossing.

The under 80 mW figure belongs to a complete PFC plus LLC system at 230 V AC, not to the controller alone. That distinction matters when a customer compares it against a competitor's controller only number, because the measurement includes the gate charge and the LLC standby draw.

Burst mode with soft entry and soft exit is there to keep the audible noise down at light load. A transition mode controller that simply skips cycles produces a low frequency envelope that a laminated inductor turns into noise, and the soft periods spread that out.

The 8.5 V to 34 V supply range lets the controller run from an auxiliary winding across the whole line range without a pre regulator, which is why the part is used in adapters that have to work from 90 V to 264 V AC.

The second over voltage comparator is independent of the first. One protects the output divider path and the other catches a fault in the feedback loop itself, so a single resistor failure does not take the output above the capacitor rating.

The over temperature protection is internal and has no external set point, so the thermal margin of the board is decided by the package and the copper rather than by a resistor. On a six pin SOT-23 in a sealed adapter that is the constraint that decides how much power the stage can carry at 60 C ambient.

The valley delay component is the one external part that a copy of a reference circuit is most likely to get wrong. It sets how long the controller waits after the drain voltage has started to fall, and a value taken from a board with a different inductor and output capacitor will either switch before the valley or miss it entirely. The same component also sets the minimum off time, so a value chosen only for valley timing can leave the controller unable to follow a fast line transient.

The 46 uA startup current is what allows the bias to be built from a high value resistor from the bulk. On a 230 V AC input that resistor dissipates less than a tenth of a watt, which is the difference between meeting a standby target and missing it before the controller has even started switching.

The second over voltage comparator is independent of the feedback divider, so it works when the divider itself has failed. That is the fault that takes an output capacitor over its rating in a transition mode boost, and having a second path that does not share the divider is the reason the part needs only six pins to cover the protection set.

The multi-mode operation at light load is what keeps the efficiency curve flat instead of falling off a cliff below 20 per cent load. The controller moves between transition mode and discontinuous conduction as the load falls, and the audible noise is handled by the burst periods rather than by holding a fixed frequency down to no load.

What a six pin controller can and cannot do

Six pins means the gate driver, the current sense, the feedback, the compensation and the supply all share the package with no spare. That is why the valley delay is set by an external component rather than by a register, and why the current limit is cycle by cycle rather than a programmable threshold with a soft start ramp.

The consequence for a buyer is that the part is a cost play. It replaces an eight or fourteen pin controller in a product where the power stage is already transition mode and the only open questions are the light load efficiency and the standby power, both of which are the two numbers the document leads with.

What the under 80 mW figure actually measures

The number is a system figure at 230 V AC with a PFC stage and an LLC stage, which means it includes the gate charge of both stages, the bias of both controllers and the leakage of the bulk capacitor chain. Read on its own it looks like a controller specification, and a customer who compares it against a competitor's controller only figure is comparing two different measurements.

The 8.5 V to 34 V supply window is wide enough that the bias can come from an auxiliary winding with a poor coupling coefficient, which is common on a small adapter where the winding has few turns. A narrower window would force a pre regulator and a second stage of loss in exactly the product where every milliwatt of standby counts.

Where this order code fits

AC to DC adapters, television and monitor supplies, LED lighting drivers and appliance power are the applications the family is sold into, and each of them is judged on standby power and light load efficiency. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the boost inductor need an auxiliary winding? No. The controller switches at the drain valley, so the zero crossing is inferred from the drain voltage and no second winding is required.

Which revision is on this page? The plain UCC28056DBVR. The A, B and C revisions are separate rows in the same addendum, so a customer asking for the newest silicon should be quoted against the row that matches the build.

What supply voltage does it need? Anywhere from 8.5 V to 34 V, with a startup current below 46 uA so the bias can be built from a high value resistor at first power up.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.