UCC24612-2DBVR
Product Specifications
UCC24612-2DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC24612-2DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC24612-2DBVR: a synchronous rectifier controller that senses the drain to source voltage of the secondary FET, runs to 800 kHz, clamps the gate at 9.5 V and sits in a five pin SOT-23 on a 3000 piece reel
UCC24612-2DBVR is a secondary side controller that turns a MOSFET on and off in place of a rectifier diode, using the voltage across the FET itself as the timing signal, so the converter loses the diode drop without adding an isolated gate drive in a SOT-23 body of 5 pins. The DBV body is the five pin SOT-23 and the whole secondary side rectifier function fits in it: one pin for the drain sense, one for the gate, one for the bias, one for the regulated rail and one for the source reference.
Order code and package
| Catalogue string | UCC24612-2DBVR, where 24612 is the controller, -2 is the 800 kHz variant with the longer minimum on time, DBV is the five pin SOT-23 and R is the large reel |
| Body | SOT-23, DBV outline, five pins, the smallest body this function is offered in |
| Reel | 3000 pieces on a large reel for the R string, with 250 pieces on a small reel under DBVT for prototypes and a second 250 piece row under the .B revision |
| Status | Active in production, with the plain row, the .B row and the G4 row all listed, and the G4 row at the small reel quantity only |
| Finish and moisture | NIPDAU at moisture level 1 for 260 C with no floor life limit |
| Temperature | minus 40 to 125 C, the same range the electrical table is specified over |
| Marking | 6122 on the body, which is how the -2 variant is distinguished from the -1 on a populated board |
| Document | SLUSCM5A, August 2017, revised February 2018 |
Electrical parameters that decide the application
| Drain sense | the VD pin stands off 230 V, so the controller can sit on the secondary of an offline converter and read the FET drain directly without a divider |
| Bias range | VDD operates from 5 V to 28 V, covering a 5 V output rail and a 28 V rail with the same part and no pre-regulator |
| Gate clamp | the gate is clamped at 9.5 V, which keeps the drive loss of a large logic level FET inside the thermal budget of a small secondary side part |
| Drive strength | 4 A of sink and 1 A of source, asymmetric on purpose, because turning the FET off before the primary starts the next cycle matters more than turning it on fast |
| Turn on delay | 170 ns typical on this variant against 80 ns on the -1, which is the trade that buys noise immunity in continuous conduction mode |
| Minimum on time | 540 ns on this variant against 375 ns on the -1, so a spurious edge has to last longer before the FET is turned on |
| Turn off delay | 16 ns typical, because a late turn off is what causes reverse current to flow back through the secondary |
| Maximum frequency | 800 kHz on this variant, against 1 MHz on the -1, which is the other half of the same trade |
| Bias current | 105 microamps typical in the start state, 0.92 mA running at 12 V, and 390 microamps in standby at 12 V, which lets the controller sleep at light load instead of switching |
| Regulated rail | the internal regulator turns on at 4.5 V and off at 3.65 V, so the part protects itself when the output rail collapses during a fault |
| Off time window | the absolute minimum off time is 400 ns and the maximum off blanking is 3.68 microseconds, the window inside which the next cycle has to be recognised |
| Light load | below the sleep threshold the controller stops driving and draws the standby current, which is what lets a charger meet a no load power target with a synchronous rectifier in the output |
Family variants and how they differ
| UCC24612-1 | 1 MHz maximum, 80 ns turn on delay, 375 ns minimum on time, the variant for a converter that switches fast and has a clean drain waveform |
| UCC24612-2 | 800 kHz maximum, 170 ns turn on delay, 540 ns minimum on time, the variant for continuous conduction mode and active clamp flyback where ringing is present |
| High side use | the same part can be configured for a high side rectifier, which is why the drain sense pin has its own 230 V rating rather than being referenced to the source |
| Cycle limit | a cycle limit pre-turn-off function ends the on time before the primary switch is allowed to conduct, which prevents the reverse current that a simple comparator would allow in continuous conduction mode |
| Adaptive off time | the minimum off time adapts to the switching period, so a converter that changes frequency across its load range does not need the off time resistor recalculated |
| Package siblings | the same function exists in larger bodies from other vendors, and the five pin outline is the one that fits a secondary side board without a second keep out area |
Points to check before this part goes on a BOM
The -1 and -2 variants are not interchangeable by suffix alone. The -2 doubles the minimum on time to 540 ns and lengthens the turn on delay to 170 ns, so a board that was tuned for the -1 sees a rectifier that stays on longer and turns on later, and in a continuous conduction mode converter that changes the reverse current at the switching transition.
Sixteen nanoseconds of turn off delay is the number that decides survivability. Any delay between the drain voltage rising and the gate falling lets current flow backwards through the FET, and in a hard switched converter that current is limited only by the transformer leakage, so the 4 A sink is there to make the gate fall before the drain has moved far.
The 9.5 V gate clamp is a loss decision as much as a protection decision. Driving a secondary FET to 12 V or higher costs charge on every cycle, and the clamp keeps the drive loss low enough that a SOT-23 part can run at 800 kHz without a heat path.
Sleep mode at 390 microamps is what makes a synchronous rectifier usable in a charger that has to meet a no load power limit. Above the sleep threshold the part switches, below it the body diode carries the small current and the controller draws its standby current, and the crossover has to be checked on the actual board because it depends on the primary side behaviour.
The 230 V drain rating sets the topology limit, not the output voltage. In a flyback the drain swings to the input voltage plus the reflected output plus the leakage spike, so a 230 V part is comfortable on a 90 to 264 V input flyback only when the leakage clamp keeps the spike inside that number, and an active clamp flyback is the topology where this part is normally found.
Reading the drain waveform the controller reads
The controller has no current sense and no timing input from the primary. It sees the drain to source voltage of the FET it drives, turns on when that voltage goes negative by the body diode drop, and turns off when the current has fallen to near zero and the voltage starts to rise.
That means the sense trace is part of the timing circuit. A long trace with a via in it adds inductance that shifts the crossing point, and the controller then turns off early at light load and late at heavy load, which is why the sense pin is normally routed as a short direct connection to the drain.
Where this order code fits
Secondary side rectification in active clamp flyback, quasi resonant and continuous conduction mode flyback converters, LLC stages, USB Type C and power delivery adapters, and server or telecom auxiliary supplies that need the diode drop removed without an isolated drive Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
Why choose the -2 over the -1? The -2 has twice the minimum on time and twice the turn on delay, so it ignores the ringing that follows a primary switching edge. It is the safe choice in continuous conduction mode and in active clamp flyback.
Does it work on a 20 V output? Yes. The bias range is 5 V to 28 V and the drain pin stands off 230 V, so a 20 V rail biases the part directly with no pre-regulator.
What limits the switching frequency? 800 kHz on this variant. Above that the minimum on time of 540 ns occupies too much of the period and the rectifier conduction angle collapses.
Is a gate resistor needed? A small turn off resistor is often added in series with the gate return to control the drain voltage rise, but the 4 A sink is what sets the turn off speed, and a large series resistor undoes it.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.