Contact Us

UCC24610DR

Brand: Texas Instruments
Texas Instruments UCC24610DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC24610DR — Power Management & Signal Chain | Superb Automation

UCC24610DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC24610DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC24610DR: a secondary side synchronous rectifier controller for 5 V outputs up to 600 kHz

The UCC24610DR is a secondary side controller that turns an N channel MOSFET into a near ideal rectifier by sensing the drain to source voltage across it. It is optimised for 5 V outputs, works from 4.5 V to 5.5 V, runs at switching frequencies up to 600 kHz and needs no current transformer, no dedicated winding and no primary side signal. The gate impedance is 1.6 ohm sink and 2.0 ohm source, the turn-off propagation delay is 20 ns typical with 16 ns minimum and 35 ns maximum, and the part can be biased straight from the 5 V output it is rectifying.

Its value is in the efficiency it recovers on the secondary of a flyback or an LLC converter. A Schottky rectifier on a 5 V, 5 A output drops about 0.4 V, which is 2 W of loss, and that loss sits on the secondary where the thermal path is worst. A 10 milliohm MOSFET drops 50 mV at the same current, which is 0.25 W, and the controller that makes it behave like a diode costs one SOIC-8 and a handful of resistors. The sleep current is specified for 90 plus efficiency converters, and the part wakes from sleep on its own when the drain voltage indicates conduction.

Key electrical data for the UCC24610DR

FunctionSecondary side synchronous rectifier controller, VDS sensing, no primary side signal needed
Output windowOptimised for 4.5 V to 5.5 V, usable outside that window with reduced benefit
FrequencyUp to 600 kHz operating, SYNC input for continuous conduction mode operation
Gate drive1.6 ohm sink and 2.0 ohm source impedance, turn-off propagation 16 ns minimum to 35 ns maximum
ModesAutomatic light load management, synchronous wake-up from sleep, micro-power sleep current
GradeJunction -40 C to 125 C, 8 pin SOIC body

Package, marking and reel data

BodyD, 8 pin SOIC, 3.9 mm by 4.9 mm nominal
Reel2500 pieces on a large reel, 75 pieces per tube on the tube row
FinishNIPDAU, level 1 at 260 C with unlimited floor life
Marking24610 on the top, the DR suffix is the reel and the D suffix the tube

What the VDS sensing actually measures

The controller watches the voltage across the MOSFET and turns the gate on when the body diode starts to conduct, then turns it off when the current falls to a level where the drain voltage crosses a threshold. That threshold and the blanking time after turn-on are the two settings that decide whether the part behaves well or rings. Too little blanking and the turn-on transient trips the comparator; too much and the body diode conducts for longer than it should on every cycle, which is exactly the loss the part is bought to remove.

The SYNC input matters in continuous conduction mode, where the secondary current does not reach zero and the drain voltage never gives a clean turn-off cue. In that mode the controller takes a timing signal from the primary side or from the gate of the primary switch, and a converter that omits it will show shoot-through on the secondary at light load. A 5 V, 5 A adapter with a 600 kHz flyback is the classic application, and our power management cross reference page lists the rectifier controllers and MOSFETs we kit together for it.

Buyer questions on the UCC24610DR

Can this replace a Schottky diode without a board change? No. It needs a MOSFET, a gate resistor, a timing resistor and a connection to the drain, so the footprint changes even though the function is the same. The gain is 0.3 W to 2 W of loss depending on the output current.

Does it work on a 12 V output? It can run outside its optimised window, but the internal bias and the sensing thresholds are set for 5 V systems, so a 12 V secondary needs a different controller rather than this one with a divider.

What is the floor life? Level 1 at 260 C means unlimited floor life, so a reel can sit open on the shelf without a bake. That is the main handling difference against the modules in this band, which are level 2 and level 3.

Availability and cross reference

The reel row is 2500 pieces and the tube row is 75 pieces, which makes the tube useful for a prototype without opening a full reel. Both rows are active and both carry NIPDAU at level 1. We keep the DR row in stock and kit it with the 30 V synchronous rectifier MOSFETs that match the 5 V window, and our kitting service page describes how the controller and the MOSFET are paired on a build.