Contact Us

UCC23313DWYR

Brand: Texas Instruments
Texas Instruments UCC23313DWYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC23313DWYR — Power Management & Signal Chain | Superb Automation

UCC23313DWYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC23313DWYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC23313DWYR: a single channel isolated gate driver with a 3.75 kVRMS basic barrier, 4.5 A of source current and a 105 ns maximum propagation delay, in the same stretched six pin SOIC as its reinforced sibling

UCC23313DWYR is an isolated gate driver with an emulated diode input and a rail to rail output stage that delivers 4.5 A source and 5.3 A sink from a supply up to 33 V, rated for basic insulation rather than reinforced in a SOIC body of 6 pins. The DWY body is the stretched six pin SOIC at 7.50 mm by 4.68 mm with more than 8.5 mm of creepage, identical to the reinforced member of the family, and the part exists so that a product which only needs basic insulation does not pay for a barrier it will never claim.

Order code and package

Catalogue stringUCC23313DWYR, where DWY is the stretched six pin SOIC and R is the 850 piece large reel
BodySOIC, DWY, six pins, 7.50 mm by 4.68 mm with more than 8.5 mm of creepage and clearance, the same moulding as the 5.7 kVRMS part
Reel850 pieces on a large tape and reel, and no larger reel is published for this body
Finish and moistureNIPDAU plating, with the plain row printing Call TI in the moisture column and the .A row of the same string printing level 2 at 260 C and one year
Temperatureminus 40 to 125 C on every row of the addendum, with the electrical table taken to 150 C junction
MarkingUCC23313 on the body; the 8 V lockout member carries UC23313B and a different order code
DocumentSLUSDS6B, September 2019, revised October 2020
StatusActive and in production on the addendum dated 6 February 2026

Electrical parameters that decide the application

Isolation rating3.75 kVRMS basic insulation, with 5300 VPK of maximum transient voltage, 990 VPK repetitive peak and 700 VRMS of working voltage
Barrier geometrymore than 8.5 mm of external creepage and clearance, more than 17 um of distance through the insulation and a tracking index above 600
Output current3 A minimum and 4.5 A typical source, 3.5 A minimum and 5.3 A typical sink, into a 180 nF load with 10 us pulses
Supply range15 V to 30 V recommended on the output side with 33 V absolute maximum, so a 15 V rail with a negative bias fits comfortably
Lockout, 12 V versionrising at 11 V minimum, 12.5 V typical and 13.5 V maximum, falling at 10 V, 11.5 V and 12.5 V, with 1 V of hysteresis
Lockout, B versionrising at 7.8 V, 8.5 V and 9.2 V, falling at 7.05 V, 7.75 V and 8.45 V, with 0.75 V of hysteresis
Propagation delay70 ns minimum and 105 ns maximum in both directions, with 25 ns of pulse width distortion and 35 ns of part to part skew
Input stagean emulated diode with a 1.5 to 4 mA forward threshold and a recommended forward current of 7 to 16 mA, so the drive is a resistor from the controller
Reverse handling15 V of reverse breakdown on the input, with 13 V of reverse polarity handling, which allows a bipolar drive or an interlock without a series diode
Common mode immunity150 kV per microsecond minimum in either output state, measured with 1500 V of common mode across the barrier
Output edges28 ns rise and 25 ns fall into 1 nF, with 20 to 30 us of recovery after the lockout releases
Insulation lifequoted above 50 years in the feature list, which is the number that makes the part an upgrade from an LED based driver rather than a sidegrade

Family variants and how they differ

UCC23313, the part on this page3.75 kVRMS basic, 5300 VPK transient, 12 V lockout, for a product whose standard requires basic insulation only
UCC23313Bthe same silicon with an 8 V lockout, so a 12 V rail can drive a logic level FET without sitting in lockout
UCC235135.7 kVRMS reinforced and 8000 VPK transient in the same body, the part to specify when the end product needs reinforced insulation
The -Q1 gradethe automotive member has its own document and order codes, so a bill of materials that needs AEC-Q100 should name it rather than infer it
Against an optocoupler driver105 ns maximum against several hundred nanoseconds, and an insulation life quoted in decades rather than in hours of operation
Against a digital isolator plus a discrete driverone body instead of two, and a current driven input instead of a logic level input

Points to check before this part goes on a BOM

The only difference between this part and the reinforced member of the family is the barrier rating, and that difference is worth money on a product that ships in volume. The body, the pins, the drive current, the delay and the lockout options are the same. What changes is 3.75 kVRMS basic against 5.7 kVRMS reinforced, 5300 VPK against 8000 VPK of transient, and 700 VRMS of working voltage against 1500 VRMS. A board that fits this part can be moved to the reinforced one without a board change, which is the reason to keep the two order codes side by side in a bill of materials.

Basic insulation is not a lesser version of the same claim, it is a different claim. Basic insulation protects against a single fault, and reinforced insulation protects against the same fault plus a second independent one. A product with a metal enclosure that is earthed and a low voltage bus can be built with basic insulation; a product where a person can touch the isolated side, or a medical product with a patient connection, cannot. The honest way to choose is to read the end product standard first and the driver datasheet second, because the datasheet cannot tell you which claim the product is allowed to make.

The 850 piece reel applies to every member of this family and it catches new programmes out. A distributor search that returns a price per piece often assumes a full reel, and a line that plans on 3000 pieces will need two reels to build 1000 boards. The practical consequence is inventory: a partial reel has to be counted as a partial reel, and a programme that consumes 500 pieces a month will hold a lot of part value in a single reel rather than spreading it across a steady flow.

The input side is driven by current, not by voltage, and the recommended forward current is 7 to 16 mA. A controller with a 3.3 V push pull output and a 220 Ohm resistor gives about 5 mA after the 2.1 V threshold, which is below the recommended band and will work at room temperature and drift at the corners. The resistor should be sized from the lowest supply rail and the highest threshold, which for 3.3 V and 2.4 V leaves 0.9 V across the resistor and asks for 100 Ohm at 9 mA. A 100 Ohm resistor dissipates 81 mW and the controller has to be able to source it continuously.

The 105 ns maximum propagation delay is specified from the input threshold crossing to the output reaching 10 or 90 per cent, not from the pin voltage edge, and the 35 ns part to part skew is what keeps a bridge balanced. In a half bridge the two drivers are usually the same part from the same reel, so the skew between them is a fraction of the 35 ns figure, but the dead time still has to be set from the maximum delay plus the switch's own turn off time. A dead time taken from the typical 70 ns figure will be too short at the corner and will show up as shoot through current on a hot board rather than as a failure on the bench.

The insulation life claim above 50 years is worth reading against the working voltage. It is a projection from a time dependent breakdown test at the rated working voltage, and it does not survive being scaled up. A product that runs the barrier at 700 VRMS has the full projection; one that runs it at 900 VRMS is outside the rating and has no projection at all, whatever the field history suggests. That is the same arithmetic that applies to the reinforced part, and it is the reason the working voltage is printed separately from the withstand voltage.

Choosing between the basic and the reinforced member of one family

The two parts share a footprint, a pinout and a drive rating, so the choice is made by the safety standard and by nothing else on the board. A 400 V three phase drive with an earthed frame and a low voltage control side is the classic basic insulation case, and the cost saving per unit across thousands of boards is worth the paperwork of justifying it. A charger with a user accessible connector, an instrument with a patient connection or a product with a floating secondary is the reinforced case, and the 5.7 kVRMS part is the one that keeps the review short.

The trap is a product that starts as basic and gains a user accessible port in a later revision. At that point the barrier has to be re justified, and a part that was correct for two years becomes the item on the critical path. Keeping the reinforced order code in the approved vendor list from the beginning, even if the basic part is what ships, is cheap insurance against that revision.

What the driver cannot fix later

The gate loop inductance is set by the board, and no driver specification survives a loop that is 30 mm long. The output stage can deliver 4.5 A in 28 ns, which is a di/dt that will ring against 20 nH of loop inductance and put a spike on the gate that exceeds the 33 V supply rating. The resistor in series with the gate is the damping, and the return path under the driver is the other half of the fix. A board that adds the resistor and ignores the return path will still see the spike, just at a lower frequency.

The isolation barrier itself cannot be improved by the board either. Creepage is a property of the package plus the slot or the cut out around it, and a board that runs a copper pour under the driver has reduced the effective distance through the board even though the package still measures more than 8.5 mm across its own surface. The vendor's board note says to keep copper away from under the part, and that instruction is a safety requirement rather than a suggestion.

Where this order code fits

This is the gate driver in an industrial motor drive, a servo amplifier, a photovoltaic inverter or a switched mode supply, wherever the end product needs basic insulation and the cost of a reinforced barrier cannot be justified Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is this part a drop in for the 5.7 kVRMS member? Electrically and mechanically yes, both are the stretched six pin SOIC with the same pin functions. The barrier rating is lower, so the substitution is only valid where the end product standard allows basic insulation.

Does it isolate the gate power? No. The signal is isolated, the output supply is not. The secondary side needs its own bias referenced to the emitter of the switch.

Which version runs from a 12 V rail? The B version with the 8 V lockout. The plain part needs 12.5 V typical to leave lockout.

Can it drive a silicon carbide FET? Yes, up to 33 V of supply and 4.5 A of source current, which is enough for a module with a few hundred nanocoulombs of gate charge at moderate frequency.

Why is the moisture column empty on the plain row? The plain row prints Call TI in the finish and moisture columns while the .A row prints NIPDAU and level 2. Treat the .A row as the one with a published moisture rating.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.