UCC21710QDWRQ1
Product Specifications
UCC21710QDWRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC21710QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC21710QDWRQ1: a reinforced isolated single channel gate driver for silicon carbide and IGBT switches, with plus or minus 10 A of drive, a 4 A Miller clamp, 5.7 kVRMS of isolation and an isolated analogue to PWM sensor, in the sixteen pin wide SOIC
UCC21710QDWRQ1 is a galvanically isolated gate driver that sits between a low voltage controller and a high side or low side power switch, and that protects the switch with its own over current detection, soft turn off and fault report rather than leaving that work to the controller in a SOIC body of 16 pins. The DW body is 10.3 mm by 7.5 mm with more than 8 mm of creepage and clearance under the barrier, which is what a 1.5 kVRMS working voltage and a 12.8 kVPK surge requirement demands at this pin count.
Order code and package
| Catalogue string | UCC21710QDWRQ1, where 21710 is the device, Q marks the automotive qualification, DW is the sixteen pin wide SOIC, R is the large reel and the closing Q1 repeats the qualification |
| Body | SOIC, DW outline, sixteen pins, 10.3 mm by 7.5 mm, with creepage and clearance above 8 mm across the barrier |
| Reel | 2000 pieces on a large reel on the rows the document publishes for this body |
| Qualification note | the document in hand is the industrial UCC21710 data sheet and it prints only the UCC21710DW and DWR rows, with a pointer to a separate automotive document for the Q1 version, so the automotive rows have to be confirmed against that document before an order is placed |
| Finish and moisture | NIPDAU plating at moisture level 2 for 260 C with a one year floor life, which is a different handling class from the level 1 parts around it |
| Isolation | 5.7 kVRMS single channel isolation, 1.5 kVRMS of working voltage with a barrier life beyond forty years, 12.8 kVPK of surge, reinforced per VDE 0884-17 and recognised under UL 1577 |
| Temperature | minus 40 to 150 C junction for the industrial device, with the row range on the addendum printed as minus 40 to 125 C |
| Drive capability | plus or minus 10 A peak source and sink with split output pins, so the turn on and turn off paths can carry separate gate resistors |
Electrical parameters that decide the application
| Output supply | 33 V maximum between VDD and VEE, which covers a plus 15 V and minus 8 V gate swing on a silicon carbide switch with margin |
| VDD lockout | 10.5 V minimum, 12.0 V typical and 12.8 V maximum on the rising edge, with the ready flag held low until the output supply is above the threshold |
| Input supply lockout | 2.55 V minimum, 2.7 V typical and 2.85 V maximum rising, and 2.35 V to 2.65 V falling, so a 3.3 V or 5 V controller rail can feed the input side |
| Propagation delay | 60 ns minimum, 90 ns typical and 130 ns maximum in both directions, with 30 ns maximum of pulse width distortion between the two edges |
| Common mode immunity | 150 V per nanosecond minimum, which is the figure that decides whether a fast silicon carbide edge couples through the barrier as a false command |
| Over current threshold | 0.63 V minimum, 0.70 V typical and 0.77 V maximum on the OC pin, with a 40 mA pull down current when the pin is driven |
| Over current timing | 120 ns of deglitch filter, 270 ns to the output falling to 90 per cent and 530 ns to the fault flag going low, all typical |
| Soft turn off | 250 mA minimum, 400 mA typical and 570 mA maximum when the fault path takes over, which limits the di/dt so the switch does not see the full short circuit current on the way out |
| Miller clamp | 4 A of internal clamp current on a dedicated pin, which holds the gate low through the dv/dt that would otherwise turn the switch back on through its own gate drain capacitance |
| Analogue sense | the AIN pin accepts 0.6 V to 4.5 V and converts it to a PWM stream at 400 kHz, with 10 per cent duty at the bottom of the range, 50 per cent at 2.5 V and 88 per cent at the top |
| Fault reporting | the FLT pin goes low within 530 ns of an over current event and stays muted for at least 550 microseconds before a reset through the RST/EN pin is accepted |
| Input noise | the input pins reject transients shorter than 40 ns, which is the filter that keeps a switching node's ringing from being read as a command |
Family variants and how they differ
| Split output | OUTH and OUTL are separate pins so the turn on resistor and the turn off resistor can differ, which is the only practical way to tune a silicon carbide edge without changing the switch |
| Miller clamp pin | CLMPI is a separate terminal rather than a feature of the output stage, so the clamp trace runs to the gate on its own path and does not share the drive return |
| Ready and fault | RDY reports the output supply, FLT reports a fault, and both are open drain so they can be wired together across several drivers on one controller input |
| Reset and enable | RST/EN both resets a latched fault and disables the output, and the response is fast enough to be used as the primary shutdown path for the bridge |
| Isolated sensing | the AIN to APWM path is inside the barrier, so a temperature or DC link measurement crosses the same isolation as the drive with no second isolator and no second set of creepage rules |
| Barrier family | the same barrier and pinout appear across the vendor's single channel isolated drivers, so a lower current member can replace this one where the gate charge is smaller |
| Automotive version | the Q1 order code carries the automotive qualification and its own document, and the pinout is the same, so a board that is qualified with the industrial part does not need a board change to take the automotive one |
Points to check before this part goes on a BOM
The 130 ns maximum propagation delay is the number to hold onto when the dead time is being set, not the 90 ns typical. Two drivers in a half bridge can differ by 60 ns between their own minimum and maximum, and the pulse width distortion adds 30 ns on top of that, so a dead time taken from typicals leaves nothing at the corners.
Soft turn off is a separate current source at 400 mA rather than the main output pulled low quickly. On a short circuit this matters: switching off a silicon carbide device at 10 A of gate current produces a di/dt that the stray inductance turns into a voltage spike across the switch, and the 400 mA path is what keeps that spike inside the rating.
The analogue to PWM converter has a fixed 400 kHz output and a duty that runs 10 per cent to 88 per cent across 0.6 V to 4.5 V. Reading it needs a capture timer with enough resolution at 400 kHz, and a controller that measures the duty with a 1 microsecond timer sees only 25 counts across the whole range.
The document in hand is the industrial version. The order code on this page carries the automotive qualifier, and the vendor points to a separate document for that version. Anything on this page about temperature grade, addendum rows and qualification comes from the industrial tables, so the automotive part number, its reel and its grade must be confirmed against the automotive document before a purchase order goes out.
The 40 ns input filter is short compared with the 130 ns propagation delay, so a genuine command passes while a switching transient does not. On a board where the controller sits more than a few centimetres from the driver, the trace has to be treated as a high speed line rather than as a logic signal.
Isolation working voltage of 1.5 kVRMS is not the same as the 5.7 kVRMS test voltage. A 400 V or 800 V DC link sits comfortably inside the working voltage, but the pollution degree and the altitude of the installation set the creepage that must actually be held on the board, and that is a mechanical decision rather than a part number decision.
What the automotive suffix changes
The Q1 suffix on a vendor part number means the device went through the automotive qualification flow with its own test plan, its own temperature grade and its own documentation. It does not mean a different die, and it does not mean the parameters on the industrial page can be assumed for the automotive rows.
For a build that has to be traceable, the automotive order code and the automotive document have to travel together. A distributor quote that names the Q1 string against an industrial data sheet is worth a question before the parts are kitted.
Where this order code fits
Motor drives in traction inverters and compressor controllers, on board chargers and DC to DC stages in electric vehicles, solar and storage inverters, uninterruptible supplies and server power stages where a silicon carbide or IGBT half bridge has to be driven across an isolation barrier Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
What is the difference between the isolation ratings? 5.7 kVRMS is the one minute withstand from UL 1577, 1.5 kVRMS is the working voltage the barrier is rated for continuously, and 12.8 kVPK is the surge. A product has to satisfy all three, and the creepage on the board decides the third.
Can the driver protect the switch by itself? Yes for over current. The OC pin compares against 0.7 V, filters for 120 ns, turns the output off through the 400 mA soft path in 270 ns and reports on FLT in 530 ns.
Is a negative gate supply required? No, but VDD to VEE can go to 33 V, which is what allows a negative rail for a silicon carbide switch that needs one to stay off through fast dv/dt. The clamp pin can also be used with a single supply.
How is temperature measured across the barrier? The AIN pin takes an NTC, a PTC or a thermal diode signal between 0.6 V and 4.5 V and converts it to a 400 kHz PWM duty, so the controller reads temperature without a second isolator.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.