Contact Us

UCC21520QDWRQ1

Brand: Texas Instruments
Texas Instruments UCC21520QDWRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC21520QDWRQ1 — Power Management & Signal Chain | Superb Automation

UCC21520QDWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC21520QDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC21520QDWRQ1: an automotive isolated dual channel gate driver with 4 A of source and 6 A of sink current, 5.7 kVRMS of reinforced isolation, 33 ns of typical propagation delay and 125 V/ns of common mode immunity, in the sixteen pin SOIC on a 2000 piece reel

UCC21520QDWRQ1 is two independent isolated channels that can be wired as a half bridge with programmable dead time, a pair of low side drivers or a pair of high side drivers, with a disable pin and a fail-safe that forces both outputs low in a SOIC body of 16 pins. The DW body is 10.3 mm by 7.5 mm with more than 8 mm of creepage, and the Q1 suffix carries the automotive qualification on the same die as the industrial part.

Order code and package

Catalogue stringUCC21520QDWRQ1, where Q is the automotive qualifier, DW is the sixteen pin SOIC, R is the 2000 piece large reel and the closing Q1 repeats the qualification
BodySOIC, DW, sixteen pins, 10.3 mm by 7.5 mm, with the isolation barrier running between pins 8 and 9 and 8.1 mm of creepage on the isolation variant
Reel2000 pieces on a large tape and reel, against 3000 or more on most parts in this size, so the reel count has to be named on the order
TubeUCC21520QDWQ1 in a tube is marked Obsolete on the addendum dated 6 February 2026, so a prototype comes from a cut reel
Finish and moistureNIPDAU plating, with the plain row printing Call TI in the moisture column and the .A row printing level 3 at 260 C with a 168 hour floor life
Temperatureminus 40 to 125 C ambient on the ordering rows, with the electrical table specified to 150 C junction
MarkingUCC21520Q on the body
DocumentSLUSCQ2E, October 2017, revised June 2024
QualificationAEC-Q100 grade 1 and functional safety quality managed, with documentation available for a system safety case

Electrical parameters that decide the application

Isolation, withstand5.7 kVRMS for one minute per UL 1577, which is the number a production hipot test demonstrates
Isolation, reinforced8000 VPK per DIN EN IEC 60747-17, which is the transient rating the safety standard uses
Working voltage1500 VDC between the two secondary side drivers, and 700 VDC across the barrier for the working voltage figure a reviewer checks
Surge10 kV of surge immunity, with a barrier life quoted above 40 years
Common mode125 V per nanosecond minimum of transient immunity, measured with 1500 V of common mode across the barrier
Input railVCCI from 3 V to 18 V, so a 3.3 V digital controller and a 5 V analog controller both drive it without a level shifter
Output railVDD up to 25 V on each side, with 5 V and 8 V lockout options
Lockout, 5 V optionrising at 6.0 V with a 5.7 V to 6.3 V window, falling at 5.7 V with a 5.4 V to 6.0 V window, and 0.3 V of hysteresis
Lockout, 8 V optionrising at 8.5 V with a 7.7 V to 8.9 V window, falling at 7.9 V with a 7.2 V to 8.4 V window, and 0.6 V of hysteresis
VCCI lockoutrising at 2.7 V and falling at 2.5 V, so the part is alive at a 3.3 V rail with 10 per cent of tolerance
Input thresholds1.8 V typical high, 1.0 V typical low and 0.8 V of hysteresis, with minus 5 V of negative transient tolerance on a 100 ns pulse
Peak current4 A source and 6 A sink, asymmetric so that turn-off is faster than turn-on
Timing33 ns of typical propagation delay, 20 ns of minimum pulse width and 6 ns of maximum pulse width distortion
Dead timeprogrammable from a resistor between DT and ground, where the delay in nanoseconds is 10 times the resistance in kOhm, from 2 kOhm to 500 kOhm, and tying DT to VCCI allows the outputs to overlap
Quiescent current1.4 mA on VCCI and 1.0 mA per output channel, rising to 3.0 mA per channel while switching at 500 kHz

What the sixteen pins do

INA, INBthe two channel inputs, each with its own threshold and each able to drive either output
DISthe disable pin, pulled low or left open for normal operation, asserted high to shut both outputs down through the isolated barrier
DTthe dead time pin, where a resistor to ground sets the delay and a connection to VCCI allows the two outputs to overlap
VCCIthe input side bias, 3 V to 18 V, with a 0.1 uF capacitor at the pin
VDDA, VDDBthe two output side bias rails, each up to 25 V and each with its own lockout
OUTA, OUTBthe two gate outputs, 4 A source and 6 A sink, referenced to their own return
VSSA, VSSBthe two output returns, which are independent of each other and of the input ground

Points to check before this part goes on a BOM

Three isolation numbers appear on this page and they answer three different questions. The 5.7 kVRMS for one minute is a withstand test and says the barrier survives a hipot at the end of the line. The 8000 VPK reinforced rating under the German standard describes a transient and is what a safety reviewer compares with the over-voltage category of the product. The 1500 VDC between the two output sides is a working voltage and is the number that decides whether the barrier holds for twenty years, because insulation fails slowly under continuous stress and instantly under a surge. A specification that quotes the withstand number and runs the barrier at 1200 VDC continuously passes the production test and fails in the field.

The 5 V and 8 V lockout options are chosen from the switch and not from the rail. A silicon MOSFET or a GaN device wants 5 V to 8 V of gate drive and is fully on at that level, so a 5 V lockout version protects it from a partial turn-on that would heat the die. An IGBT or a silicon carbide FET wants 15 V and is not fully on below 12 V, so the 8 V version lets a 15 V rail start the part while still protecting the gate from a supply that has collapsed. Picking the 5 V version for an IGBT means the part starts at 6 V and the IGBT runs in its linear region until the rail comes up.

The dead time resistor is a single component that decides the efficiency of the bridge. Ten nanoseconds per kOhm from 2 kOhm to 500 kOhm gives a range of 20 ns to 5 us, and the value is set once and checked at temperature, because the internal current source that converts the resistance into a delay has its own drift. A 100 kOhm resistor gives 1 us, which is right for a slow IGBT and ruinous for a silicon carbide half bridge that wants 100 ns. Tying the pin to VCCI removes the dead time entirely and allows the two outputs to conduct at the same time, which is only correct when the two channels drive separate loads or when the overlap is wanted for a synchronous rectifier.

The disable pin is a fast shutdown rather than a slow one. Asserting it high turns both outputs off within the propagation delay, and the primary side logic failures in the input stage also force both outputs low, which is the fail-safe behaviour an automotive inverter wants. What the pin cannot do is isolate the output side: the barrier stays biased, the outputs go low rather than floating, and a motor that is spinning still pushes current through the freewheeling diodes. A board that needs the gate held off during a fault uses this pin; a board that needs the driver to disappear from the circuit needs a relay or a contactor.

The 4 A source and 6 A sink are sized for a gate charge of a few hundred nanocoulombs at up to 100 kHz, and the asymmetry is deliberate. Turning a FET on slowly limits the di/dt and the ringing, and turning it off fast limits the time spent in the linear region during a fault. The six amps of sink current is what allows a 300 nC gate to fall in 50 ns, and the same current is what produces the negative spike on the source inductance that the board has to control. A gate loop with 10 nH of inductance and 6 A of di/dt in 20 ns produces 3 V of source bounce, which is enough to turn a paralleled device partly on.

The 2000 piece reel is a supply chain fact that catches a production plan. Most isolated drivers in a sixteen pin body ship 3000 to a reel, and this one ships 2000 with the tube version marked Obsolete. A line that plans 3000 pieces per reel for a month of production is short by a third on the first order, and a prototype build has no tube option to fall back on. The reel size belongs in the purchase order and in the material plan, next to the part number, because the two are not independent.

Two channels, three topologies

The same sixteen pin body can drive a half bridge, two low side switches or two high side switches. In a half bridge the two channels share the switch node, one output referenced to the high side rail and one to the switch node, and the internal functional isolation between the two output sides has to hold the full bus voltage. In a dual low side arrangement the two channels drive separate FETs referenced to the same ground, and the functional isolation carries no voltage at all.

The topology has to be chosen before the dead time resistor is fixed, because a half bridge wants dead time and a dual low side arrangement does not. Tying DT to VCCI for the second case removes the dead time entirely and lets the two channels switch together, which is the correct setting for two independent loads and the wrong one for a bridge.

Why 6 ns of pulse width distortion matters

A short pulse on the input has to appear as the same short pulse on the output, and 6 ns of distortion means a 30 ns pulse becomes 24 ns or 36 ns depending on which edge. In a converter running at 100 kHz that is noise; in a board that sends a short pulse to the gate for a soft turn-off during a fault, the shortest pulse is the one that has to survive, and a driver that stretches it by 6 ns leaves the FET on longer than the protection wanted.

The 20 ns minimum pulse width is the other side of the same number. A controller that produces a 15 ns pulse, which happens at light load in a discontinuous converter, will lose it entirely, and the output will skip a cycle rather than deliver a narrow one. That is a normal behaviour and not a fault, but it has to be accounted for when the control loop is compensated at light load.

Where this order code fits

Isolated gate drive in electric vehicle traction inverters, on-board chargers and DC to DC converters, solar string inverters, motor drives and any bridge where the high side sits on a floating rail Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the two channels form a half bridge? Yes. The two output sides are functionally isolated from each other, so one can sit on the bus and the other on the switch node.

How is the dead time set? A resistor from DT to ground, 10 ns per kOhm from 2 kOhm to 500 kOhm, and tying DT to VCCI allows the outputs to overlap.

What is the difference between the 5 V and 8 V versions? The lockout threshold. The 5 V version suits a MOSFET or GaN gate, the 8 V version suits an IGBT or a silicon carbide FET on a 15 V rail.

Is the tube available? No. UCC21520QDWQ1 in a tube is marked Obsolete, so a prototype comes from a 2000 piece reel or a cut reel.

What happens if the input side loses power? Both outputs are forced low by the fail-safe logic, so the driven switches turn off rather than float.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.