Contact Us

UCC21520DWR

Brand: Texas Instruments
Texas Instruments UCC21520DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC21520DWR — Power Management & Signal Chain | Superb Automation

UCC21520DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC21520DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC21520DWR: a dual channel isolated gate driver with 4 A of source and 6 A of sink current, a 5.7 kVRMS reinforced barrier and resistor set dead time, in a sixteen pin SOIC on a 2000 piece reel

UCC21520DWR is two independent isolated driver channels in one body, each with its own output supply and its own lockout, arranged so they can be two low side drivers, two high side drivers or one half bridge with a dead time that is set by a resistor in a SOIC body of 16 pins. The DW body is sixteen pins on a 10.30 mm by 7.50 mm footprint with the barrier running between the input side and the two output sides, and the part exists because two discrete isolated drivers take twice the board area and never match each other as well as two channels on one die.

Order code and package

Catalogue stringUCC21520DWR, where DW is the sixteen pin SOIC and R is the 2000 piece large reel
BodySOIC, DW, sixteen pins, 10.30 mm by 7.50 mm, with reinforced isolation to the input side and functional isolation between the two output sides
Reel2000 pieces on a large tape and reel, printed against both the plain string and the .A string on the addendum dated 8 September 2026
Tube rowUCC21520DW is marked Obsolete, so the reeled string is the only routable one of the two and a prototype comes from a cut reel
Finish and moisturethe reel row prints NIPDAU against the finish and Call TI against moisture, while the .A row of the same string carries level 2 at 260 C with one year
Temperatureminus 40 to 125 C printed on the orderable rows, with a junction range of minus 40 to 150 C in the electrical table
MarkingUCC21520 on the body, with nothing on the top mark that separates it from the A revision
DocumentSLUSCJ9F, June 2016, revised November 2024, covering both UCC21520 and UCC21520A
StatusActive and in production, with the A revision also active on the same 2000 piece reel

Electrical parameters that decide the application

Isolation5.7 kVRMS reinforced for one minute per UL 1577, 8000 VPK per DIN EN IEC 60747-17, 2121 VPK of repetitive peak, 1500 V of maximum working voltage and 10 kV of surge immunity
Channel separationfunctional isolation between the two output sides, with 1500 VDC of working voltage between them, so one channel can sit on a high side node and the other on a low side node
Output current4 A source and 6 A sink peak, asymmetric by intent because turn off is where the Miller current has to be absorbed
Driver supplyup to 25 V on each output side, with 5 V and 8 V lockout versions so a silicon FET driven from 12 V and an IGBT driven from 15 V are both covered
Input supply3 V to 18 V, which lets a 3.3 V controller and a 15 V analog controller drive the same part
Dead timeset by a resistor from the DT pin to ground, with the vendor equation giving nanoseconds as ten times the resistance in kilo ohms, and overlap when the pin is tied to the input supply
Propagation delay33 ns typical, 20 ns minimum pulse width, and 6 ns maximum pulse width distortion, which is what allows switching frequencies up to about 5 MHz
Common mode immunity125 V per nanosecond minimum, measured on the barrier rather than at the pins
Input lockoutrising at 2.55 V to 2.85 V and falling at 2.35 V to 2.65 V, with 0.2 V of hysteresis, so a 3.3 V rail has margin below the lockout
Output lockout, 5 V versionrising at 5.7 V to 6.3 V and falling at 5.4 V to 6.0 V, with 0.3 V of hysteresis
Quiescent and disablethe disable pin shuts both outputs down and the part reports about 3 mA of input current when disabled, which is how a product holds a bridge off during a self test
Thermal69.8 C per W junction to ambient in the sixteen pin body, which is the lowest of the parts on this page because the moulding is large for the dissipation

Versions and how they differ

UCC21520, the part on this pagethe original die, active on a 2000 piece reel, with the 5 V and 8 V lockout options available across the order codes
UCC21520Aa revision of the same function with its own order codes, also active at 2000 pieces, and the difference is in the pull up behaviour during a brief turn on phase rather than in the ratings
Two channels as a half bridgeone die sets both channels, so the delay matching between the high side and the low side is a specification rather than a hope
Two channels as separate low side driverseach channel has its own output supply, so two different rails can be driven from one input side
Against two single channel driversone body, one barrier certification, one enable pin, and 6 ns of pulse width distortion instead of two parts with their own spreads
The 8 V lockout optionfor a logic level FET on a 12 V rail, where the 5 V version would sit in lockout on the same rail

Points to check before this part goes on a BOM

The dead time resistor is the feature that removes a controller function. In a half bridge the dead time has to cover the driver delay plus the switch turn off time, and if it is generated in the controller then the controller has to know the driver delay. Here the DT pin sets it inside the driver, with nanoseconds equal to ten times the resistance in kilo ohms, so a 10 kOhm resistor gives 100 ns. Shorting the pin to the input supply allows overlap, which is a mode a phase shifted full bridge uses on purpose, and leaving the pin open is not a supported state because there is no defined open circuit behaviour in the equation.

The 1500 VDC of functional isolation between the two output sides is what lets one part drive a half bridge. Both channels share the input side but not the output side, so the high side channel can sit on a switch node that swings 600 V while the low side channel sits on ground, and the barrier between them is rated for the difference. Without that internal separation a dual driver would need two separate barriers to the input and would be no cheaper than two parts. The number to check is the working voltage between the two output grounds, which is the 1500 VDC figure rather than the 8000 VPK transient.

A 33 ns typical propagation delay with 20 ns minimum pulse width is what makes the part usable at 5 MHz. The pulse width distortion of 6 ns maximum is more important than the delay, because distortion is what turns a symmetric drive signal into an asymmetric gate waveform and unbalances the switching loss between the high side and the low side. At 100 kHz a 6 ns distortion is 0.06 per cent of the period and invisible. At 2 MHz it is 1.2 per cent of the period and shows up as a temperature difference between two switches that are supposedly identical.

The moisture column reading Call TI on the plain reel row is the kind of detail that stops a production release. The finish is published as NIPDAU and the moisture level is not, while the .A row of the same string carries level 2 at 260 C with one year of floor life. A process instruction that states a floor life has to come from a published row, so either the .A row is bought or the level is confirmed against the vendor packaging page. Filling in a level 2 because it is the common value for a body this size is a guess, and a guess in a process instruction becomes a bake step that costs hours.

The single most common schedule problem with this part is the obsolete tube row. A first article build naturally asks for 20 or 50 pieces, the catalogue lists a tube string, and that string is marked Obsolete on the current addendum. The reel row is 2000 pieces. A buyer who does not notice will quote a lead time against a part that is not being packed any more, and the build slips by weeks. The workaround is a cut reel from a distributor, ordered by the reeled string so the traceability stays on the same order code.

What a dual channel driver changes on a board

Two single channel drivers need two barriers, two enable arrangements and two sets of input supplies, and their delays are specified separately so the matching between them is the sum of two spreads. One dual driver specifies the matching between its own channels, and 33 ns typical with 6 ns of distortion is a number that holds across the pair. On a half bridge at 200 kHz that is the difference between a dead time that can be set once and a dead time that has to be sized for the worst case of two independent parts.

The cost is in the routing. Both output sides leave the same package on the same edge, so the two gate loops share a moulding and a set of pin fields. A board that routes the high side gate loop past the low side return has created a common impedance between the two channels that no amount of dead time will fix, and the symptom is ringing on one channel that appears only when the other channel switches. The sixteen pin body wants a split under the part, with the two output grounds meeting only at the star point of the power stage.

Where the reinforced rating stops

5.7 kVRMS reinforced with 1500 V of working voltage and 2121 VPK of repetitive peak covers a 400 V or 690 V motor drive with a floating high side, and it covers the mains side of an off-line converter whose switch node stays under 1000 V. Above that the limiting number is the working voltage rather than the withstand, because the barrier is being stressed continuously and the life of the insulation falls with the stress rather than with the test result.

The other place the rating stops is a medical product with a patient connection. Reinforced insulation to an information technology standard is not the same claim as two means of patient protection, and a safety reviewer will ask for the medical standard rather than for the isolation number. The part is still usable, and the application note has to be written for the medical standard rather than for the industrial one, which is a documentation task that is cheaper to start early than to fix at the review.

Where this order code fits

This is the driver pair in a half bridge or a full bridge of an off-line converter, a battery charger, a solar inverter, a server power supply or a motor drive, where two floating switches have to be driven from one controller Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How is the dead time set? By a resistor from the DT pin to ground, with nanoseconds equal to ten times the resistance in kilo ohms. Tying the pin to the input supply allows overlap, which a phase shifted bridge uses deliberately.

Can the two channels drive different rails? Yes. Each output side has its own supply pin, so one channel can run at 15 V for an IGBT and the other at 12 V for a silicon FET.

What is the isolation between the two outputs? Functional isolation with 1500 VDC of working voltage, which is what allows one channel to sit on a high side node while the other sits on ground.

Is the tube version available? No. UCC21520DW is marked Obsolete, and the reeled string at 2000 pieces is the routable one.

What is the difference from the A revision? The same function with its own order codes and its own pull up behaviour during a brief turn on phase, and both are active at 2000 pieces per reel.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.