Contact Us

UCC21222DR

Brand: Texas Instruments
Texas Instruments UCC21222DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC21222DR — Power Management & Signal Chain | Superb Automation

UCC21222DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC21222DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC21222DR: 4 A source and 6 A sink isolated dual gate driver in a 16 pin SOIC

UCC21222DR is an isolated dual channel gate driver in the 16 pin D body that drives two N channel MOSFETs or IGBTs across a 3 kV RMS barrier, with 4 A peak source and 6 A peak sink current and a 33 ns propagation delay in a SOIC-16 body of 16 pins. The UCC21222 takes its logic side from a 3.3 V or 5 V supply and its output side from a driver supply of up to 25 V, with 5 V and 8 V undervoltage lockout options. The two channels are universal: they can be wired as two low side drivers, two high side drivers or one half bridge, and a resistor on the RDT pin programs the dead time. A DIS pin turns both outputs off for supply sequencing, and the barrier holds better than 125 V per ns of common mode transient, with input transients shorter than 5 ns rejected.

Order code and package

Order codeUCC21222DR
Channels2, isolated
Isolation rating3 kV RMS
Peak source current4 A
Peak sink current6 A
Output supply, VDDup to 25 V
Undervoltage lockout options5 V and 8 V
Logic supply3.3 V or 5 V
Package16 pin SOIC, D body
DocumentSLUSCX6C, revised November 2024

Electrical parameters that decide the application

Junction temperature rangeminus 40 C to 150 C
Propagation delay33 ns typical
Pulse width distortion5 ns maximum
VDD power up delay10 us maximum
Common mode transient immunitygreater than 125 V per ns
Input transient rejectionpulses shorter than 5 ns ignored
Dead time settingresistor on RDT, values at or below 0.15 kohm
Channel configurationdual low side, dual high side or half bridge
DisableDIS pin turns both outputs off
Undervoltage lockouton every supply, VCCI and both VDD rails

Points to check before this part goes on a BOM

Five nanoseconds of pulse width distortion is a small number until it is compared with the period. At a 2.4 MHz switching frequency the period is 417 ns, so 5 ns is 1.2 percent of the duty cycle, and a controller that asks for 10 percent duty at that frequency gets somewhere between 9.4 and 10.6 percent. At 10 MHz the period is 100 ns and the same distortion is 5 percent, which is the point where a narrow pulse intended for a resonant converter stops being predictable. The specification is a maximum over the full temperature range, so it is the term to use when the operating point sits near the minimum on time of the stage.

The 33 ns propagation delay is a typical figure and the distortion above is a maximum, and the difference between the two matters when both channels are used as a half bridge. What decides shoot through is not the absolute delay but the mismatch between the two channels of the same package, which is why the dead time resistor exists. A dead time set too short turns the body diode of the lower device on for the duration of the interval, and a dead time set too long puts the full reverse recovery of that diode into the upper switch at every cycle. On a 400 V rail with a 100 nC gate, each extra 10 ns of dead time is roughly 10 ns of diode conduction at the load current, which at 20 A is 200 nC of charge removed per cycle from the rail.

The barrier is rated for 125 V per ns of common mode transient, which converts to 125 kV per microsecond. A 400 V bus that switches in 20 ns produces 20 V per ns, a sixth of the rating, so the figure is not the limiting term in a conventional hard switched stage. Where it does matter is a stage with a fast silicon carbide device and a short bus loop, where 400 V in 8 ns is 50 V per ns and the margin has halved. The same specification applies when the high side source node rings after turn on, and that ringing is the transient the driver sees as a common mode step rather than as a voltage on its own supply.

Six amps of sink current is what turns a gate off quickly, and the number only means something against the gate charge. A device with 100 nC of total gate charge is discharged from 15 V to the threshold in about 60 nC divided by 6 A, which is 10 ns, and the plateau that follows is set by the transfer characteristic rather than by the driver. That is why a bigger driver current stops helping once the gate loop inductance dominates: a 10 nH loop with 6 A of current change in 10 ns develops 6 V across the source lead, which appears as a negative gate voltage and can be enough to turn the device back on through its own source inductance.

The VDD power up delay of 10 us is a sequencing constraint rather than a data sheet curiosity. If the controller starts sending pulses before the output side supply has crossed its undervoltage threshold, the driver either holds the output off or, on some parts, follows the input with an undefined level. The DIS pin is the answer: it forces both outputs low from the logic side without waiting for the output supply, so a board that ties DIS to the controller reset holds the power stage off through the whole ramp. Leaving DIS floating relies on the internal state, which is a weaker guarantee than driving it.

Choosing between the 5 V and the 8 V lockout options is a question about the gate threshold of the device being driven, not about the rail. A logic level MOSFET with a 1.2 V threshold is safe with the 5 V option, and a standard planar device with a 4 V threshold needs the 8 V option so that a sagging driver supply does not leave the gate in the linear region. On a 12 V driver supply the 8 V option gives 4 V of headroom before the driver shuts down, and on a 15 V supply it gives 7 V. Below the lockout the outputs are held low, which is the safe state for a high side switch and the wrong state for a low side switch in a bridge that is expected to freewheel.

The 16 pin SOIC body carries the isolation barrier, so the spacing between the two sides is fixed by the package and cannot be improved by footprint work. That is convenient because it removes a variable, and it is a constraint because a board that needs more creepage than the body provides has to move to a wider package rather than add a slot. The 3 kV RMS rating is a barrier rating for the package, not a working voltage for the application, so the number to compare against the rail is the repetitive peak voltage and the transient the stage can deliver, with the pollution degree of the assembly taken into account.

Where this order code fits

This order code belongs on half bridge stages in telecom rectifiers, server power, motor drives, induction heating and Class D amplifiers, where a control side referenced to ground has to switch a floating high side device on a rail of several hundred volts. It is also the part chosen when two channels have to match closely, because a half bridge built from two separate single channel drivers inherits two propagation delays while this device carries both channels on one die. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the two channels drive a half bridge directly? Yes. The device is universal, so the two channels can be wired as a half bridge with one channel referenced to the switch node and the other to ground. The dead time between them comes from a resistor on RDT, and it is the only part of the timing that is not fixed by the silicon, so it is the value to check first when a bridge shows shoot through current at turn on.

How does 5 ns of distortion compare with a gate resistor? A gate resistor slows both edges equally, so it reduces the current spike and the ringing without changing the mismatch between the two channels. The 5 ns figure is a limit on the difference between the commanded and the delivered pulse width, so a gate resistor cannot recover it, and at high frequency it is the distortion rather than the resistor that sets the narrowest usable pulse.

What happens if the output supply sags below the lockout? The outputs are held low for as long as the supply stays under the threshold. For a high side device that is the safe state. For a low side device in a bridge with an inductive load it means the freewheel path is lost and the current finds the body diode of the upper switch, which is a different loss and a different recovery. The rail that feeds VDD should therefore be checked at the lowest line and the highest temperature, not at nominal.

Is the 3 kV RMS rating enough for a 400 V bus? The barrier rating and the working voltage are different numbers. 3 kV RMS is the isolation the package is qualified to, while the working voltage of the stage is the bus plus the transient the routing can deliver. A 400 V bus with a 200 V overshoot is a long way below the barrier rating, so the limiting term in that board is almost always the spacing on the board between the two sides rather than the barrier inside the package.

SUPERB holds and sources this driver line against the exact order code, with the reel, date code and country of origin stated on the offer. When a stage has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.