TPSM863252RDXR
Product Specifications
TPSM863252RDXR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPSM863252RDXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPSM863252RDXR: 3 A in the same 3.3 mm by 4 mm footprint as the 1 A module
The TPSM863252RDXR is the 3 A member of the same module family and occupies the same RDX package as the 1 A parts, 3.30 mm by 4.00 mm by 2.00 mm with the same seven pin land pattern. That pin compatibility is the commercial argument: a product family that starts at 1 A and grows to 3 A keeps one land pattern, one pick and place file and one reel setup. The electrical difference is the current limit, which moves to 3.1 A minimum, 4.1 A typical and 5.1 A maximum on the valley set point, and the negative limit at 1.5 A to 2.5 A, which is what lets the part survive a load that pushes current back into the output.
The 3 A member runs at 1.2 MHz rather than 1.4 MHz, which is the change that keeps the loss inside the package. Conduction loss at 55 milliohm and 24 milliohm with 3 A is roughly 0.7 W, so the package and the copper under it do the thermal work, and the switching frequency drop trims the switching term. The output range is 0.6 V to 10 V on this code, the input is 3 V to 17 V, and the reference window is the same 600 mV with 1 percent at 25 C and 1.5 percent over the full temperature range.
Key electrical data for the TPSM863252RDXR
| Input range | 3 V to 17 V, UVLO wake 2.9 V, shutdown 2.7 V, 200 mV hysteresis |
| Output | 0.6 V to 10 V adjustable, 594 mV to 606 mV feedback at 25 C |
| Current | 3 A continuous, valley limit 3.1 A to 5.1 A, negative limit 1.5 A to 2.5 A |
| Switches | 55 milliohm high side and 24 milliohm low side at 25 C |
| Switching | 1.2 MHz nominal, 95 percent maximum duty, 60 ns minimum on time |
| Quiescent | 100 microamps no load in Eco-mode, 2 microamps shutdown, 1.6 ms soft start |
Package, marking and reel data
| Body | RDX, 7 pin QFN-FCMOD, 3.30 mm by 4.00 mm by 2.00 mm |
| Reel | 3000 pieces on a 330 mm reel, 12.4 mm carrier, pocket 3.6 by 4.3 by 2.25 mm on the 257 carrier |
| Finish | NIPDAU at level 2 on the plain row, SN at level 3 with a 168 hour floor life on the .A row of the 252 |
| Marking and grade | 863252 on the top, -40 C to 125 C junction |
Choosing between the 3 A module and a controller with external parts
A 3 A rail from 12 V is where the module argument is strongest, because an external solution needs two MOSFETs, an inductor, a bootstrap capacitor, a compensation network and a board arrangement that keeps the switch node small. The module contains all of that and the vendor has already characterised the loop, so the board bring-up consists of checking the input capacitor and the output capacitor and enabling the part. Where the module loses is on cost at high volume and on flexibility: the output cannot be pushed past 10 V, the frequency is fixed, and the current limit cannot be trimmed.
For a 5 V rail at 3 A the module dissipates about 0.7 W and needs roughly 25 mm by 25 mm of copper on the top and bottom layers to hold the junction below 100 C in a 60 C ambient. For a 1.2 V core rail at 3 A the duty cycle is 10 percent and the low side switch carries most of the conduction, so the same copper budget applies. Our power management cross reference page lists the second sources for the 3 A class.
Buyer questions on the TPSM863252RDXR
Is the reel size the same as the 1 A parts? Yes, 3000 pieces on a 330 mm reel, but the pocket height differs on the 257 carrier at 2.25 mm against 2.30 mm, so the feeder setup is not identical for every member of the family.
What is the difference between the plain row and the .A row? The plain row is NIPDAU at moisture level 2 with a one year floor life. The .A row of the 252 is SN plated at level 3 with a 168 hour floor life, so the bake rule changes with the row a distributor ships.
Can the part run from a 5 V bus? It can, down to 3 V, but the UVLO wakes at 2.9 V and the 5 V rail sits close enough to the floor that a sag during a load step can trip the lockout. A 5 V bus with heavy transient load should use the 4.5 V to 28 V family instead.
Availability and cross reference
Both rows ship 3000 pieces per reel. Where the two rows differ is the plating and the moisture level, and that is the detail that decides whether a lot can go straight to reflow or needs a bake, so we record it per lot rather than per part number. Customers moving a 1 A rail to 3 A keep the same land pattern and the same inductor, which means the change can be made on a running build without a new stencil, and our pin to pin cross reference page documents the family that shares this body.