TPSM861257RDXR
Product Specifications
TPSM861257RDXR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPSM861257RDXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPSM861257RDXR: the 5.5 V ceiling is the reason this member exists
The TPSM861257RDXR is the third member of the TPSM86125x family, with the same 3 V to 17 V input, the same 1 A rating and the same 55 milliohm and 24 milliohm switches, but with an output range that stops at 5.5 V instead of 10 V and a forced continuous loop that holds 1.4 MHz at every load. The narrower range is not a limitation in practice. It is what the vendor specifies when the internal divider and the feedforward network are optimised for the 5 V region, and it is the member that a 12 V or 24 V bus uses to make a clean 5 V rail for relays, CAN transceivers, USB charging ports and analog front ends.
Because the converter never enters pulse skipping, the ripple stays at the switching frequency and the emission profile is predictable. A 5 V rail that feeds a current loop amplifier or a 16 bit ADC reference benefits from that: the ripple sits at 1.4 MHz where a small ferrite bead and a ceramic capacitor remove it, instead of at a few kilohertz where the filter would have to be large. The trade is 370 microamps of no load current against 100 microamps on the Eco-mode member.
Key electrical data for the TPSM861257RDXR
| Input range | 3 V to 17 V, UVLO 2.9 V wake and 2.7 V shutdown with 200 mV hysteresis |
| Output | 0.6 V to 5.5 V adjustable, feedback 600 mV typical with a 594 mV to 606 mV window at 25 C |
| Current | 1 A continuous, valley limit set point 1.5 A to 3.1 A |
| Switches | 55 milliohm high side and 24 milliohm low side at 25 C, high side 68 milliohm at 3 V in |
| Switching | 1.4 MHz fixed in forced continuous mode, 95 percent maximum duty, 60 ns minimum on time |
| Quiescent | 370 microamps no load with switching, 2 microamps shutdown, 1.6 ms soft start |
Package, marking and reel data
| Body | RDX, 7 pin QFN-FCMOD, 3.30 mm by 4.00 mm by 2.00 mm |
| Reel | 3000 pieces on a 330 mm reel, 12.4 mm carrier, pocket 3.6 by 4.3 by 2.3 mm |
| Finish | NIPDAU, level 2 at 260 C, one year floor life |
| Marking and grade | 861257 on the top, -40 C to 125 C junction |
Where a forced continuous 5 V rail pays for itself
The obvious case is a mixed signal board with a 12 V input, a 5 V analog rail and a 3.3 V digital rail. The analog rail feeds an instrumentation amplifier and a 16 bit converter, and the converter's rejection at 1.4 MHz is far better than at the 20 kHz to 60 kHz band where a skipping converter puts its energy. The second case is a 5 V rail that also supplies a USB port: a load step from 10 mA to 900 mA has to stay inside the USB droop window, and a fixed frequency loop with a 22 microfarad output capacitor recovers in a few switching cycles.
The thermal check is simple. At 12 V in and 5 V out with 1 A, conduction loss in the two switches is about 79 milliwatts and the switching loss adds a similar amount, so the package dissipates well under a quarter of a watt and the junction stays far from the 125 C limit even in a sealed enclosure at 70 C ambient. The part to watch is the input capacitor, which carries 1 A of pulsating current at 1.4 MHz and has to be a ceramic of the right dielectric rather than a tantalum. The power management cross reference page lists the equivalent codes we hold for this rail.
Buyer questions on the TPSM861257RDXR
Why is the output limited to 5.5 V when the 252 reaches 10 V? The internal divider and the feedforward capacitor are set for the 5 V region on this member. Above 5.5 V the loop is not characterised, so the 252 with an external divider is the correct part for a 9 V or 10 V rail.
Does forced continuous operation cost efficiency at light load? It does. The inductor current reverses and the part circulates energy instead of skipping pulses, so a 10 mA load runs at lower efficiency than the Eco-mode member. The benefit is constant ripple and predictable emission.
Can two modules share a 5 V rail for more current? Not by paralleling the outputs directly. Two modules in parallel fight over the load because neither has current sharing, so a 2 A load needs the 3 A member rather than two 1 A parts.
Availability and cross reference
This code is published at 3000 pieces on a large reel and shares the reel size with the other two members, which means a change from the 253 to the 257 does not change the packaging, the pitch or the pick and place data. We keep the three codes on the same forecast line because customers move between them during a build, and the date code on a partial reel is recorded on our date code management record so a mixed lot never reaches a conformal coating step without its bake history.