TPSM82823ASILR
Product Specifications
TPSM82823ASILR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPSM82823ASILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPSM82823ASILR: a 3 A step down power module with the inductor inside a 1.1 mm package, in forced PWM
TPSM82823ASILR is a synchronous step down converter with an integrated inductor, a forced PWM loop and a power good output in a MicroSiP body in a MicroSiP (SIL) body of 10 pins. It takes 2.4 V to 5.5 V in and delivers 3 A at an adjustable output from 0.6 V to 4 V while running at a fixed 4 MHz, which is what makes a 2.0 mm by 2.5 mm by 1.1 mm module a complete rail. The A version never enters power save mode, so the output ripple stays small at light load, which is the property that matters in an optical module or a measurement front end. Quiescent current is 4 microamp when switching, the high side and low side switches are 26 milliohm each, and the module is stated to meet CISPR 11 class B without an external filter.
Order code and package
| TPSM82823ASILR | MicroSiP body of 10 pins measuring 2.00 mm by 2.50 mm by 1.10 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 2 at 260 C with one year of floor life, marking L7, active status in the addendum dated 12 August 2026 |
| TPSM82823SILR | the same 3 A module with automatic power save mode instead of forced PWM, which is the string to order when light load efficiency matters more than ripple |
| TPSM82821 and TPSM82822 | the 1 A and 2 A members of the same family in the same body, with the same pinout, so a board can be re-rated without a copper change |
| Fixed output members | the numbered strings in the family carry 1.2 V, 1.8 V, 2.5 V and 3.3 V set inside the module, which removes the divider and two parts from the board |
| Inductor | inside the package, which is the whole point of the family: the switching node, the inductor and the output capacitor loop are already short, so the emissions performance does not depend on the board as much as it does with a discrete converter |
| Solution size | 12 square millimetres for the fixed output members, which is the figure the vendor quotes against a discrete converter with the same rating |
Electrical parameters that decide the application
| Input voltage | 2.4 V to 5.5 V in the recommended table, which fits a single cell lithium rail or a 3.3 V or 5 V bus |
| Output voltage | 0.6 V to 4 V adjustable through the feedback divider on this member, with the fixed members covering 1.2 V to 3.3 V |
| Output current | 3 A for this string, with the vendor note that the current has to be derated when the ambient and the dissipation together push the junction past 125 C |
| Switch resistance | 26 milliohm typical on the high side and 26 milliohm on the low side, which is the pair that sets the conduction loss at 3 A |
| Current limit | 3.7 A minimum, 4.3 A typical and 5.0 A maximum on the high side switch, with a minus 1.6 A negative limit on the low side for the forced PWM members |
| Switching frequency | 4 MHz nominal at 1 A, fixed, which is why the inductor fits inside the package and why the output ripple is small |
| Quiescent current | 4 microamp typical and 10 microamp maximum with the part enabled and not switching, and 50 microamp typical while switching in forced PWM |
| Dropout resistance | 70 milliohm typical and 95 milliohm maximum in 100 per cent duty mode at 2.7 V in, which is the figure that sets how close the output can come to the input |
| Soft start | internal, which is what keeps the inrush current out of the input supply when the rail comes up |
| Power good | open drain with a window comparator, and the pull-up may go to any rail up to 5.5 V, so it can drive a 1.8 V or 3.3 V logic input |
| Protection | hiccup short circuit protection and overtemperature protection, both inside the module |
| Emissions | stated to meet CISPR 11 class B, which is a system level claim that still depends on the board ground and the input capacitor placement |
| Thermal | the module is a 1.1 mm body with the inductor on top, so the pad and the copper under it are the only heat path |
Power save and forced PWM members of the module family
| TPSM82823ASILR | the 3 A forced PWM module covered by this order code, adjustable output, inductor inside the package |
| TPSM82823SILR | the same 3 A module with automatic power save instead of forced PWM, which trades ripple for light load efficiency |
| TPSM82821 and 82822 | the 1 A and 2 A members, same body, same pinout, so a board can be re-rated without a copper change |
| Fixed output members | the numbered strings in the family carry 1.2 V, 1.8 V, 2.5 V and 3.3 V inside the module, which removes the divider from the board |
| Negative current limit | minus 1.6 A on the forced PWM members, which is what stops a back fed rail from running away at light load |
| Emissions | stated to meet CISPR 11 class B, with the input capacitor and the ground under the module still deciding the result on a real board |
| Derating | the 3 A rating has to be reduced when the dissipation and the ambient together push the junction past 125 C |
Points to check before this part goes on a BOM
The inductor is not a component the board can change. That is the trade: a module fixes the inductance, the switching frequency and the ripple, so the rail performs the same on every board and cannot be tuned. A board that needs a different ripple or a different frequency needs a discrete converter instead.
Forced PWM costs light load efficiency and buys a clean spectrum. The A version keeps a fixed 4 MHz at all currents, so the output ripple does not change with load and there is no low frequency component for a radio or a converter to pick up. The plain member saves current at light load and shows a bursty spectrum instead.
The 3 A rating has a derating clause attached. The vendor states that high dissipation and high ambient together require the output current to be reduced. A 3 A rail at 5 V in and 1 V out in a sealed enclosure is a thermal question before it is an electrical one.
The negative current limit belongs to the A members. Forced PWM allows current to flow back into the input at light load, and the minus 1.6 A limit is what stops that from running away. A board that back feeds the rail has to account for it.
Power good is a window comparator, not a single threshold. It releases inside a band around the nominal output and drops outside it, so a rail that sags under load and recovers does not chatter the signal the way a single threshold part would.
CISPR 11 class B is a starting position. The module makes the switching loop short, which removes most of the radiated problem, but the input capacitor and the ground under the module still decide whether the board passes. A first build should still be scanned.
Where a module beats a discrete converter
An optical module, a machine vision head or a PLC backplane has very little board area and no room for a switching loop that has to be kept short by hand. The module puts the inductor and the switch node inside one body, so the part of the emissions problem that board copper usually decides is already decided.
The same argument applies to a product built in several factories: a module removes the variation between boards that comes from inductor placement and from the copper of a second assembly site.
Reading the current derating curve before the rail is specified
The 3 A figure holds while the junction stays inside 125 C. At 5 V in and 1 V out the module dissipates a few hundred milliwatts, and inside a sealed enclosure at 85 C ambient that is enough to force a lower current. The derating curve in the document is the figure to plan against, not the headline.
Where this order code fits
a point of load rail in an optical module, a machine vision head or a PLC where board area and emissions both matter Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.
Questions buyers ask
What is the difference between this and the TPSM82823SILR? The plain member enters power save mode at light load and gives better efficiency there. This A member runs forced PWM at all currents, so the ripple and the switching spectrum stay the same from no load to 3 A.
Can the output be set below 0.6 V? No. The feedback reference and the divider set a 0.6 V floor, so a core rail below that needs a different part.
Is an external inductor needed? No, the inductor is inside the module, which is why the total solution is 12 square millimetres on the fixed output members and why the switching loop is already short.
What current is available at 85 C ambient? Below 3 A in most cases. The vendor states that high dissipation and high ambient together require derating, and the derating curve in the document is the number to use rather than the headline rating.
Does the module need an external output capacitor? Yes, the output capacitor is still external, and it sets the transient response and the ripple. The module fixes the inductor and the frequency, not the capacitance.
How are the reels packed? 3000 pieces on a large reel at moisture level 2, so the reel has one year of floor life after it is opened rather than the 168 hours of a level 3 part.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.