Contact Us

TPSM828221SILR

Brand: Texas Instruments
Texas Instruments TPSM828221SILR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM828221SILR — Power Management & Signal Chain | Superb Automation

TPSM828221SILR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM828221SILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM828221SILR: a fixed 1.2 V rail at 2 A with 4 uA of standby current

The TPSM828221SILR is the 2 A, fixed 1.2 V member of the MicroSiP family, and the order code is worth reading carefully because it sits in the middle of a numbering block that also contains the 1 A and the 3 A parts. The 828221 is a two amp module with the output set at 1.2 V inside the package, in the same 2.0 mm by 2.5 mm by 1.1 mm ten pin body, with 2.4 V to 5.5 V of input and a 4 MHz switching frequency in PWM mode. Because the divider is internal, the feedback pin connects directly to the output and there is no resistor pair to place, match or route.

The power save mode is on by default on this member, so the module draws 4 uA when the load is idle and switches continuously when the load is real. A 1.2 V rail at 2 A is the shape of a core supply for an FPGA fabric, a DDR memory termination or a processor I/O ring, and those loads alternate between microamps and amps within a few microseconds. The DCS-Control loop is what makes that alternation survivable without an external compensation network and without a large output capacitor bank.

Key electrical data on the page

Input and output2.4 V to 5.5 V in, 1.2 V fixed at 2 A, with 1.8 V, 2.5 V and 3.3 V members on the same pad
Switching4 MHz nominal in PWM, DCS-Control, no external compensation
Quiescent4 uA in power save mode, with the module stopping switching at light load
Accuracy1.188 V to 1.212 V on the fixed 1.2 V output at 25 C in PWM mode
Dropout90 milliohm typical and 120 milliohm maximum in 100 percent duty mode at 2.7 V in
Current limithigh side switch 2.7 A to 3.9 A, so the 2 A rating has real headroom on a step load
Power goodwindow comparator, open drain, pull up to 5.5 V, flags an overvoltage as well as a droop
Protectionhiccup short circuit, thermal shutdown, active output discharge on disable

Package, marking and reel data

BodyuSiL SIL, 10 pins, 2.0 mm by 2.5 mm by 1.1 mm, inductor integrated on the die
Reel3000 pieces on a 330 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q1
PocketA0 2.25 mm, B0 2.75 mm, K0 1.25 mm, carrier width 8.0 mm
Finish and moisturelevel and finish per the orderable addendum of the current revision

Fixed output versus adjustable, in numbers

The fixed 1.2 V member saves two resistors and the tolerance they add, and it also saves the standing current of the divider. On a 1.2 V rail a 10 k divider draws 100 uA continuously, which is twenty five times the 4 uA the module itself uses in standby, and that difference shows up directly in a battery budget. The adjustable member exists for rails that have to move during development or that need a value outside the fixed set, and it pays for that flexibility with the divider current.

The 2 A rating has to be read against the thermal path. The module is 1.1 mm tall and the inductor sits on top of the die, so heat leaves through the pads and the board, not through the top of the package. At 2 A from 5 V to 1.2 V the loss is roughly 300 mW, which on a small board with 1 oz copper is a 25 to 40 C rise depending on the pour. A rail that sits at 2 A continuously in a sealed box needs the copper area the datasheet assumes, and a rail that peaks at 2 A for a few milliseconds does not.

Buyer questions on the TPSM828221SILR

Is this the same body as the 1 A part? Yes, the 10 pin uSiL pad is shared across the 1 A, 2 A and 3 A members, so a board can move up or down in current without a new footprint. The output voltage is fixed per order code.

Can the 1.2 V output be adjusted on the board? No. This member has the divider inside the package and the feedback pin connects straight to the output. The adjustable members are the ones without a digit in that position.

Does it need a minimum output capacitor? Yes, and the value depends on the output voltage and the ripple target. At 4 MHz the requirement is small, typically two 10 uF ceramics, but it is a specified minimum and not a suggestion.

Buying this part through a component supplier

Fixed output modules are ordered by the rail they produce, and a code with seven digits is easy to confuse with its neighbours. We keep the 828211, 828221 and 828231 lines separate in the store and record the marking on the label through date code management. For a board that carries several of these rails, BOM consolidation covers ordering them as one kitted shipment, and the kitting service page lists what a line side kit can include.