Contact Us

TPSM82821SILR

Brand: Texas Instruments
Texas Instruments TPSM82821SILR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM82821SILR — Power Management & Signal Chain | Superb Automation

TPSM82821SILR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM82821SILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM82821SILR: 1 A at 4 MHz in a module 1.1 mm tall

The TPSM82821SILR is the 1 A member of the MicroSiP family, a complete step-down converter and inductor in a 10 pin package of 2.0 mm by 2.5 mm by 1.1 mm. The input is 2.4 V to 5.5 V, the output is adjustable from 0.6 V to 4 V, and the converter switches at a nominal 4 MHz in PWM mode, which is why the output capacitor can be two small ceramics and the inductor fits on top of the die. The thin profile is the specification that sells it: a board that has to sit under a display connector or inside a 2 mm enclosure cannot use a conventional inductor, and this module plus two capacitors solves the whole rail.

The S in the order code is the standard power save version, not the spread spectrum option of the larger 8281x family. In power save mode the converter stops switching at light load and draws 4 uA of quiescent current, which is what keeps a coin cell or a small lithium pack alive through months of standby. The A version of the same die runs forced PWM at all currents and draws more at light load, so the choice between the two is a standby budget decision rather than a performance one.

Key electrical data on the page

Input and output2.4 V to 5.5 V in, 0.6 V to 4 V out adjustable, 1 A continuous
Switching4 MHz nominal in PWM, DCS-Control topology with no external compensation
Quiescent4 uA in power save mode, which is the number that sets a standby life
Accuracy1 percent on the feedback voltage, 1.188 V to 1.212 V on the fixed 1.2 V members in PWM
Duty cycle100 percent, so the module passes the input through when the rail sags to the output level
Power goodwindow comparator on an open drain pin, pull up to 5.5 V, 1 mA sink capability
Protectionhiccup short circuit, thermal shutdown, output discharge when the enable goes low
EmissionCISPR11 class B compliant as a module, with the inductor shielded inside the package

Package, marking and reel data

BodyuSiL SIL, 10 pins, 2.0 mm by 2.5 mm by 1.1 mm, inductor on top of the die
Reel3000 pieces on a 330 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q1
PocketA0 2.25 mm, B0 2.75 mm, K0 1.25 mm, carrier width 8.0 mm
Finish and moisturelevel and finish per the orderable addendum of the current revision

What 4 MHz and 1.1 mm do to a board

A 4 MHz converter needs about a tenth of the inductance a 400 kHz part needs for the same ripple, and that is the whole reason the inductor fits inside the package. The cost is switching loss: at 4 MHz the gate charge is spent four million times a second, and the efficiency curve peaks at a lower current than a slower part would. In a 1 A rail feeding a sensor, a radio or a microcontroller, the load current sits near that peak and the trade is a good one. In a rail that runs at 200 mA for hours, a slower module with a bigger inductor will beat it on efficiency.

The DCS-Control loop is the second reason this module is easy to use. It has no external compensation, and it holds regulation through a load step without the ringing that a poorly compensated voltage mode converter shows, which matters on a rail that feeds a transceiver waking from sleep. The 100 percent duty cycle is the third: a 3.3 V rail from a 3.6 V battery still regulates when the pack falls to 3.4 V, and the module simply passes the input through with the switch on.

Buyer questions on the TPSM82821SILR

Does the module need an external inductor or compensation? No. The inductor is inside the package and the loop is internally compensated. The external parts are an input capacitor, an output capacitor and the feedback divider on the adjustable version.

Can the output be set below 0.6 V? No, 0.6 V is the reference and the floor of the range. A rail below that needs a different family.

What happens on a shorted output? The module enters hiccup mode: it retries at a low duty until the short is removed, and the power good flag stays low. It does not latch, so a cable fault recovers without a power cycle.

Buying this part through a component supplier

A 1.1 mm module is usually one of several rails on a dense board, and the reel of 3000 is often more than a build needs. We supply the SIL code against the BOM line and hold the date code and moisture information on the label through date code management. When a programme needs the same rail at a different current, the pin to pin cross reference shows which members of the family share the pad, and one stop BOM sourcing covers consolidating several module lines into one shipment.