Contact Us

TPSI3052DWZR

Brand: Texas Instruments
Texas Instruments TPSI3052DWZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSI3052DWZR — Power Management & Signal Chain | Superb Automation

TPSI3052DWZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSI3052DWZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSI3052DWZR: an isolated switch driver that carries its own 15 V gate supply

The TPSI3052DWZR drives a power MOSFET or a thyristor across an isolation barrier and generates the gate supply on the far side, so the secondary needs no bias winding, no isolated DC to DC module and no optocoupler. The barrier is rated 3 kVRMS for one minute per UL 1577 and 4243 V peak basic isolation per DIN EN IEC 60747-17, and the secondary rail is a regulated 15 V with 1.5 A peak source and 3 A peak sink current, which is enough to switch a large discrete FET or a pair of back to back devices for AC. In practice that replaces a solid state relay module with a driver and two FETs on the same board.

Two modes decide the pin count. In two wire mode the primary side is powered from the same 6.5 V to 48 V rail that the switch controls, and only two pins reach the controller, which is exactly the arrangement a mechanical relay replacement wants. In three wire mode the primary runs from a 3 V to 5.5 V logic rail and a separate enable pin controls the switch, and the S version of the part adds a one shot enable for SCR triggering, where a single pulse of gate current is all that is needed.

Key electrical data on the page

Isolation3 kVRMS for one minute per UL 1577 and 4243 V peak basic isolation per IEC 60747-17
Gate supplyregulated 15 V on the secondary, no external bias required
Drive current1.5 A peak source and 3 A peak sink, enough for a large discrete FET pair
Auxiliary powerup to 50 mW of secondary supply for external circuitry such as a comparator
Primary supply6.5 V to 48 V in two wire mode, 3 V to 5.5 V externally in three wire mode
Power transferseven resistor selectable levels, traded against primary current and switching rate
Safety limiting1.4 W total, 58 mA in three wire mode and 29 mA at 48 V in two wire mode

Package, marking and reel data

BodySO-MOD DWZ, 8 pins, wide body for the isolation barrier, 12.05 mm tape pocket
Reel1000 pieces on a 330 mm reel, 16.4 mm carrier, 16 mm pitch, quadrant Q1
PocketA0 12.05 mm, B0 6.15 mm, K0 3.30 mm, carrier width 16.0 mm
Finish and moisturenickel palladium gold, level 3 at 260 C, 168 hour floor life
Marking and gradeI3052 on the top, rated -40 C to 125 C ambient

What changes when the relay becomes a driver and two FETs

A mechanical relay in a building control panel is replaced for three reasons: contact wear, coil current and acoustic noise. An isolated driver plus two back to back FETs removes all three, and the isolation rating of the driver is what keeps the mains side away from the logic side without an optocoupler that ages. The 15 V rail on the secondary means the FET can be a standard logic level or standard gate part rather than a special low threshold device, and the 50 mW of auxiliary power means a small comparator or a bleeder circuit can live on the isolated side without another supply.

The cost is a switching loss that has to be understood. The driver transfers power across the barrier to charge the gate, and that transfer is limited by the selected level, so the maximum switching frequency depends on the gate charge and the level chosen. For a 100 nC gate switched at 10 kHz the average transfer is 15 mW plus the quiescent draw, which fits comfortably inside the 1.4 W safety limit; for a 1 uC gate at 50 kHz the arithmetic no longer works and the answer is a different topology. Reading the power transfer table before choosing the FET is the step that saves a second prototype.

Buyer questions on the TPSI3052DWZR

Does the part switch AC directly? The driver switches the gates. For AC a pair of back to back FETs is used with a common source, and both gates are driven from the same 15 V rail, which is why the sink current is specified at 3 A.

What is the difference between this and an optocoupler plus a bias supply? The bias supply. An optocoupler needs an isolated rail on the secondary to drive the gate, and that rail is usually a small transformer or a charge pump with its own regulation problem. This part transfers the power across the same barrier that carries the signal.

How long does the enable take to turn the switch on? The secondary rail has to reach its undervoltage release at 13 V before the gate is driven, and the transfer level sets how fast that happens. At the higher levels the delay is in the tens of microseconds, which is fast enough for a relay replacement and not fast enough for a switching supply.

Buying this part through a component supplier

The wide body and the 1000 piece reel are unusual enough that a customer often asks whether the part exists in another package, and the answer is no: the isolation barrier sets the body. We supply the DWZ code with the level 3 moisture information on the label through date code management, because a 168 hour floor life part that sits open on a bench is a popcorn risk on the first reflow. For industrial programmes moving from a relay to a solid state switch, OEM procurement covers the qualification paperwork, and the power management cross reference lists the isolated drivers we can compare by isolation rating and drive current.