Contact Us

TPS92692QPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS92692QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92692QPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS92692QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92692QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92692QPWPRQ1: a 65 V controller with 4 percent current accuracy and a fault flag

The TPS92692QPWPRQ1 is a controller rather than a converter: the switch, the inductor and the sense resistor are external, and the part supplies the gate drive, the reference, the error amplifier and the protection. That is the right shape for automotive exterior lighting, where the string voltage runs from a few volts to over 50 V, the current is set by the customer, and the thermal path has to be spread over a board rather than concentrated in one package. The 4.5 V to 65 V input range and the 4 percent current accuracy over -40 C to 150 C junction are the two headline numbers, and both are specified rather than typical.

Spread spectrum is built in, which is unusual for a controller, and the modulation depth is set by an external ramp. A 20 k resistor at the RT pin gives 390 kHz and a 40 k resistor gives 200 kHz, so the frequency plan of a whole luminaire can be moved away from the AM band with one component. The gate driver is 5.4 ohm on the high side and 4.3 ohm on the low side, strong enough to drive a 10 nC FET at 400 kHz without a buffer.

Key electrical data on the page

Input range4.5 V to 65 V, with the internal LDO regulating VCC at 7.5 V from a 4.9 V input threshold
Current accuracy4 percent over the -40 C to 150 C junction range, with a rail to rail current amplifier
Switching200 kHz at 40 k on RT, 390 kHz at 20 k, external sync above 3.1 V with a 100 ns minimum pulse
Current limit250 mV threshold at a 5 V dim input, 700 mV at 0 V, 88 ns to 158 ns of leading edge blanking
DimmingPWM input above 1000 to 1, analog IADJ above 15 to 1, internal voltage to duty generator
Gate drive5.4 ohm high side and 4.3 ohm low side, series FET driver for the PDRV output
Diagnosticscurrent monitor output, open drain fault flag, 35 us current limit fault time

Package, marking and reel data

BodyHTSSOP PWP, 20 pins, 6.5 mm by 4.4 mm body with an exposed pad
Reel2000 pieces on a 330 mm reel, 16.4 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 6.95 mm, B0 7.10 mm, K0 1.60 mm, carrier width 16.0 mm
Finish and moisturenickel palladium gold, level 2 at 260 C, one year floor life
Marking and grade92692Q on the top, AEC-Q100 grade 1, -40 C to 125 C ambient

Why a controller instead of an integrated converter

Three reasons show up in practice. The first is topology: the same part runs a boost for a string above the battery, a buck boost for a string that crosses the battery voltage during a load dump, and a buck for a short string, because the power stage is whatever the board engineer puts around it. The second is heat: a 4 A string at 50 V is 200 W, and no eight pin package can dissipate the switching loss, so the FET has to be a separate device on its own copper. The third is diagnostics, and this is where the part pays for itself: the IMON output gives a continuous analog picture of the LED current, so the controller can tell a string that is fading from one that is open, and the open drain fault flag reports the fault without a comparator tree on the board.

The PDRV output drives a P channel series FET for dimming and protection. With the series FET off, the string is disconnected, which is what an automotive lamp needs to guarantee a dark state rather than a dim one. Combined with the internal PWM generator, a single DC voltage on the DIM pin becomes a duty cycle between 0 and 100 percent, so a simple analog harness can still produce deep PWM dimming without a microcontroller in the lamp.

Buyer questions on the TPS92692QPWPRQ1

Does the part need a separate 5 V rail? No. The internal LDO produces 7.5 V at VCC and a 4.96 V reference at VREF, both with 36 mA of current limit, and the gate driver runs from VCC. Above a 4.9 V input the part is self sufficient.

How is the spread spectrum depth set? By the ramp components on the DM pin. The internal triangle runs between 850 mV and 1.15 V with a 10 uA source and sink, so the external resistor and capacitor set how far the frequency moves.

Can it run from a 48 V rail? Yes, the input ceiling is 65 V and the LDO drops the rail to 7.5 V for the gate drive. The external FET and the inductor carry the string current and set the real thermal limit.

Buying this part through a component supplier

A 20 pin HTSSOP controller in an automotive programme is usually a long life line item, and the two reel sizes of 2000 and 250 make the prototype to production transition a single part number change. We supply both codes with the moisture level and date code recorded through date code management. For a programme looking at a second source or a lifetime buy, component obsolescence management covers the last time buy arithmetic, and the power management cross reference lists the controllers we can compare by pin count and topology.