Contact Us

TPS92630QPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS92630QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92630QPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS92630QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92630QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92630QPWPRQ1: Three-channel automotive linear LED driver, 5 V to 40 V, 150 mA per channel

TPS92630QPWPRQ1 is a three-channel linear LED driver with per-channel PWM dimming, open and short detection and thermal foldback in a HTSSOP (PWP) body of 16 pins. It sinks up to 150 mA on each of three channels from a 5 V to 40 V supply, sets the current with one reference resistor, and reports open, short and thermal faults on two pins that can be bused across fifteen devices.

Order code and package

Ordering stringTPS92630QPWPRQ1, PWP package, 16-pin HTSSOP, tape and reel
QualificationAEC-Q100 grade 1, -40 C to 125 C ambient, HBM H2 and CDM C3B
Package16-pin HTSSOP with thermal pad, 4.40 mm by 5.00 mm
Channel countThree, each with its own PWM input and its own sense pin
Parallel modeChannels can be paralleled for 450 mA into one string
Fault pinsFAULT for open, short and thermal, FAULT_S for a single shorted LED

Electrical parameters that decide the application

Input range5 V to 40 V, with operation through load dump transients handled by the external parts
Output current150 mA per channel maximum, 450 mA with three channels in parallel
Current accuracyPlus or minus 1.5 percent per channel and 2.5 percent per device above 30 mA
Dropout400 mV maximum at 60 mA per channel, 0.9 V maximum at 150 mA
Junction range-40 C to 150 C operating, shutdown at 155 C typical
Thermal foldbackStarts at 95 C minimum, 110 C typical, 125 C maximum, cutting to 40 to 60 percent of the set current
DimmingAnalog on the reference pin, PWM on each channel independently
DiagnosticsOpen load, output short, single LED short, reference resistor open and short

Points to check before this part goes on a BOM

Linear drive puts the whole difference between the battery and the string voltage into the package, so the thermal arithmetic comes before the current setting. Three channels at 150 mA with 0.9 V of dropout is 0.405 W in the HTSSOP, and the same three channels at 60 mA with 0.4 V of dropout is 0.072 W. The same part is either comfortable or marginal depending on the string length, which is why the number of LEDs in series is a thermal decision and not only an optical one.

Paralleling the three channels for 450 mA does not divide the heat by three in the way the current suggests. Each channel still drops the same voltage, so the total dissipation is three times one channel at 150 mA, and the accuracy falls back to the 2.5 percent per-device figure. Parallel mode buys current, not thermal headroom, and the thermal pad area has to be sized for the sum.

The single-short threshold is 8 V to 9 V of headroom across the channel, with 145 mV of hysteresis, and the comparator only arms once the input is above the enable threshold. A string of two LEDs on a 13.5 V rail has far more headroom than that, so a shorted LED is detected reliably, while a long string on a low rail may sit below the threshold and lose the diagnostic rather than report a false fault.

The deglitch timers are counted in PWM cycles, not in microseconds: one to three cycles for the short detection, seven to eight cycles for open load and single short. At a 200 Hz dimming frequency that is 5 ms per cycle, so a fault takes 35 ms to 40 ms to report, and a controller that polls faster than that will see the fault appear late and may blame the wrong channel.

Thermal foldback is separate from thermal shutdown and it acts before it. Foldback begins somewhere between 95 C and 125 C junction and pulls the current down to 40 to 60 percent of the set value, which keeps the lamp lit at reduced output instead of going dark. In a tail light that is the difference between a dimmed lamp and a failed lamp report, and the foldback threshold is specified as a range, so the behaviour at a given ambient is not the same on every unit.

The FAULT pin has a 500 microamp to 1 mA strong pulldown and a 4 to 16 microamp weak pullup, which is what allows fifteen devices to share one bus line without a controller pin for each. The weak pullup is also what makes the line recover on its own, so a host that latches the first fault and waits for a manual reset will hold a bus that has already cleared, and the timing has to come from the host, not from the driver.

Where this order code fits

It fits daytime running lights, position lamps, fog lamps, tail and stop lamps and interior lighting in a 12 V or 24 V vehicle system, where three strings of moderate current have to be dimmed independently and diagnosed from one package. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Does it need an external inductor? No. The driver is linear, so the only magnetic part on the board is the input filter, and the heat that a switching driver would move into an inductor stays in the package instead.

Can the channels run at different currents? All three share one reference resistor, so they are set to the same current, and independent brightness comes from the three PWM inputs rather than from three different current levels.

What is the difference between FAULT and FAULT_S? FAULT reports open load, output short and thermal shutdown on a shared line, while FAULT_S is dedicated to a single shorted LED inside a string, which is the failure that leaves the lamp lit but dimmer.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.