Contact Us

TPS92611QDGNRQ1

Brand: Texas Instruments
Texas Instruments TPS92611QDGNRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92611QDGNRQ1 — Power Management & Signal Chain | Superb Automation

TPS92611QDGNRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92611QDGNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92611QDGNRQ1: a linear automotive LED driver with a fault bus instead of a latch

The TPS92611QDGNRQ1 is a single channel linear LED driver in an eight pin HVSSOP with a thermal pad, rated for the automotive temperature grade 1 window of -40 C to 125 C ambient and qualified to AEC-Q100 with HBM level H2 and CDM level C3B. It regulates the current through an external sense resistor at 98 mV, from 4 mA to 300 mA, and does it by dropping the excess voltage across the internal pass element rather than by switching. That sounds inefficient, and it is, but it is also the reason the part has no inductor, no switching node and no emission problem, which in a dome light or a door handle lamp is worth more than the efficiency.

The feature that makes this part usable on a body control module is the FAULT pin. It is a one fails all fail bus: a single open drain line pulls low when any channel on the bus sees an open, a short or an overtemperature, and the controller learns about it without polling each driver. The DIAGEN pin exists so that the open circuit diagnostic can be disabled during a low voltage crank, when a real lamp would otherwise report as open because the supply has fallen below the forward voltage of the string.

Key electrical data on the page

Supply range4.5 V to 40 V on the supply, input and output pins rated 45 V absolute maximum
Output current4 mA to 300 mA set by an external sense resistor at a 98 mV regulation point
Dropout120 mV to 150 mV at 10 mA, 430 mV to 700 mV at 150 mA, 800 mV to 1300 mV at 300 mA
Open circuitLED open rising 70 mV to 135 mV across the driver, falling 235 mV to 335 mV
Short circuitoutput short to ground falling threshold 1.14 V to 1.26 V, rising 0.82 V to 0.91 V
Diagnosticsretry current 0.64 mA to 1.53 mA, FAULT bus rated to 7 V with a 500 uA pull up
Thermaljunction to ambient 60 C per W, junction to case 11.3 C per W at the pad

Package, marking and reel data

BodyHVSSOP DGN, 8 pins, 3 mm by 3 mm with an exposed thermal pad
Reel2500 pieces on a 330 mm reel, 12.4 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 5.30 mm, B0 3.40 mm, K0 1.40 mm, carrier width 12.0 mm
Finish and moisturenickel palladium gold with a gold flash, level 2 at 260 C, one year floor life
Marking and grade1N3X on the top, AEC-Q100 grade 1, -40 C to 125 C ambient

Thermal arithmetic in a linear driver

A linear driver at 150 mA from a 13.5 V bus into a string that drops 9 V loses 4.5 V at 150 mA, which is 675 mW. With a junction to ambient figure of 60 C per W on a good board, that is a 40 C rise above the local ambient, and in a lamp housing at 85 C the junction reaches 125 C with no margin at all. The part does not hide this: the dropout table gives 430 mV to 700 mV at 150 mA as the minimum headroom the pass element needs, and the rest is heat that has to leave through the pad. A lamp that runs a 9 V string from a 12 V bus is comfortable; one that runs a 4 V string from 13.5 V is not, and the honest answer there is a buck driver rather than a bigger heatsink.

The short circuit behaviour is worth reading before a harness is signed off. A channel shorted to ground pulls the output down and the part enters a retry at about 1 mA, so the harness sees a low current rather than a dead short, and the FAULT bus reports it. That combination is what lets a body controller distinguish a lamp that failed from a wire that is shorted, which is the difference between a service visit and a warranty claim.

Buyer questions on the TPS92611QDGNRQ1

Can two channels share one FAULT line? Yes, that is the intent. The bus is open drain and one fails all fail, so a controller reading a single input knows that at least one channel has a fault and can then enable the channels one at a time to find which one.

Why disable the diagnostic during crank? During a cold crank the supply can fall below the forward voltage of the string, and an open circuit comparator would report a healthy lamp as failed. The DIAGEN pin holds the diagnostic off through that window.

Is the sense resistor value fixed? It sets the current against the 98 mV regulation point, so 24.5 ohm corresponds to 4 mA and lower values scale up to 300 mA. The resistor tolerance enters the current accuracy directly, so a 1 percent part is the usual choice.

Buying this part through a component supplier

An automotive grade part is bought against a PPAP and a temperature grade, not just an order code, so the useful check before a purchase order is that the reel carries the Q1 suffix and the grade 1 marking. We document the date code and the moisture level through date code management, and the incoming inspection plan page sets out the checks that catch a commercial grade reel in an automotive bag. For programmes that need a second source, pin to pin cross reference is where the eight pin linear drivers are compared.