Contact Us

TPS92515AHVQDGQTQ1

Brand: Texas Instruments
Texas Instruments TPS92515AHVQDGQTQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92515AHVQDGQTQ1 — Power Management & Signal Chain | Superb Automation

TPS92515AHVQDGQTQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92515AHVQDGQTQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92515AHVQDGQTQ1: 65 V automotive buck LED driver with a 290 mOhm integrated switch and shunt FET dimming

TPS92515AHVQDGQTQ1 is a constant off time buck regulator built around an internal switch and a high side current comparator, so the LED string current is regulated without a sense resistor in the return path in a HVSSOP (DGQ) body of 10 pins. It runs from 5.5 V to 65 V, switches up to 2 A of average LED current with a 290 mOhm internal FET, and compares the drop across an external sense resistor against a 240 mV threshold that can be scaled with a voltage on the adjustment pin. Dimming runs to 10,000 to 1 with a shunt FET, 1000 to 1 with a PWM signal, and 200 to 1 in the analogue range, and the part is qualified to AEC-Q100 grade 1.

Order code and package

Ordering stringTPS92515AHVQDGQTQ1 as it appears in this catalogue, which is the high voltage automotive member in the ten pin HVSSOP
Addendum findingThe vendor packaging addendum prints TPS92515HVQDGQTQ1 and TPS92515HVQDGQRQ1 but not a string with an A in that position, so the A has to be confirmed against the vendor before a purchase order is placed
Published rowsTPS92515HVQDGQTQ1 is a 250 piece small reel and TPS92515HVQDGQRQ1 is a 2500 piece large reel, both active and in production
Part marking15QX on the high voltage automotive body, against 15OX on the non automotive high voltage member
BodyTen pin HVSSOP with the exposed pad, 3.00 mm by 3.00 mm body
MaterialRoHS compliant, nickel palladium gold finish, moisture level 2 with a one year floor life at 260 degrees
Temperatureminus 40 to 125 degrees, with the die itself rated to 150 degrees junction and the thermal pad as the only heat path

Electrical parameters that decide the application

Input range5.5 V to 65 V on the high voltage members, with operation continuing down to 5.15 V after start up, and a 4.9 V falling undervoltage lockout
Output current2 A of average LED current, with the switch itself carrying the peak and the current limit acting cycle by cycle rather than folding the converter back
Current threshold240 mV typical, 224 to 251 mV, across the external sense resistor with the adjustment pin tied to the internal 5 V rail
Adjustment pin0.1 V to 2.2 V scales the threshold with a gain of 0.1 V per volt, which gives a 10 to 1 analogue dimming range without changing the sense resistor
Switch resistance290 mOhm typical and 500 mOhm maximum at 25 degrees, 600 mOhm maximum at 150 degrees, which is the number that decides efficiency and dissipation at 2 A
Minimum on time195 ns typical and 275 ns maximum, which is what limits the duty cycle at high input and low output voltage
Off timeSet by the output voltage through the off timer, with a 1.0 V threshold and a 230 us maximum, so the frequency falls at low duty rather than the current running away
Gate drive railAn internal 5.0 V rail, 4.8 to 5.2 V, with its own 4.2 V falling lockout so the switch is not driven from a rail that is not yet valid
BootstrapThe high side drive sits on a bootstrap capacitor referenced to the switch node, with a 2.8 V falling lockout and 125 mV of hysteresis
Dimming inputsA shunt FET path that keeps the inductor current continuous, a PWM input with a 1.0 V threshold and 100 mV of hysteresis, and the analogue adjustment pin
Quiescent current0.85 mA typical and 1.5 mA maximum while not switching, with the dimming path powered down through the PWM pin
ThermalThe ten pin HVSSOP pad carries the whole dissipation, and at 2 A with 500 mOhm the switch alone produces 2 W

Family variants and how they differ

High voltage against standard membersThe 42 V members and the 65 V members share the same die and pinout, and differ in the rating of the internal switch and the drive. A 48 V rail needs the high voltage member with margin for a transient, not the 42 V one
Automotive against catalogueThe Q1 bodies are qualified to AEC-Q100 grade 1 and carry a different part marking. The electrical behaviour is the same, and the qualification is what changes for a lamp module that has to be released to a vehicle programme
Shunt FET dimmingA FET across the LED string diverts current while the converter keeps switching, so the inductor current never collapses and the light output responds faster than a converter that has to restart at every dimming edge. The 10,000 to 1 range comes from that continuity
PWM dimmingThe part can also be dimmed by gating the converter itself to 1000 to 1. Below that ratio the current pulses become long enough to see, and the shunt FET path is the one that goes deeper
Analogue dimmingThe adjustment pin scales the threshold, which changes the current amplitude rather than chopping it. That is the mode to use when colour shift matters, because the LED is driven at one current level rather than switched between two
Off timer behaviourThe off time is derived from the output voltage, so a string with more LEDs has a longer off time and a lower switching frequency. The regulator reaches a stable frequency on its own and does not need a timing component

Points to check before this part goes on a BOM

The catalogue string carries an A that the vendor packaging addendum does not print. The device is the high voltage automotive member in the ten pin HVSSOP, but the exact suffix should be confirmed against the vendor or a previous purchase before an order is placed on it.

The 2 A rating is average LED current, not switch current. The switch carries the peak of the inductor ripple on top of that average, so the sense resistor and the inductor have to be chosen against the peak rather than the average.

Switch resistance rises from 290 mOhm typical to 600 mOhm maximum at 150 degrees. At 2 A that is a change from 1.2 W to 2.4 W in the switch alone, which is why the thermal pad and the copper under it decide whether the part can hold its rating in a hot lamp housing.

The minimum on time of 195 ns limits the duty cycle. A 60 V input into a 10 V string at 2 A needs a duty below 20 per cent, and at 600 kHz that is close to the minimum on time, so the frequency falls out of the loop rather than the current being regulated badly.

The input range reaches 65 V, which is not the same as surviving load dump. A vehicle bus without a central clamp reaches far higher, and the clamp is a system part rather than something this driver can absorb.

The adjustment pin scales the current threshold and not the output voltage. A dimming signal applied there changes the light level without changing the string voltage, which is what keeps the colour point stable as the lamp dims.

What continuous inductor current buys a dimming lamp

A converter that is gated on and off to dim has to restart its inductor current at every pulse. At short on times the current never reaches its steady value, the light output is lower than the duty cycle suggests, and the colour shifts toward the blue because the LED is driven at a different current than the one it was characterised at.

Keeping the converter running and diverting the current through a FET across the string avoids both problems. The inductor current stays continuous, the light responds within a few microseconds, and the dimming ratio can go far below what gating the converter allows. The cost is one extra FET and the requirement that the driver be able to regulate into a zero volt load without losing control.

Where this order code fits

Automotive forward lighting, daytime running lamps, fog lamps and interior lighting, and industrial luminaires that run from a 48 V rail. The 65 V input rating covers a 48 V bus with margin and the automotive load dump case with a clamp in front, and the shunt FET dimming range is what makes the part usable for a lamp that has to dim smoothly to a very low level without changing colour. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is this the 42 V or the 65 V member? It is the high voltage member, rated to 65 V in and able to run down to 5.15 V after start up. The 42 V version is a different suffix in the same family.

What is the LED current accuracy? It is set by a 240 mV threshold with a 224 to 251 mV window and an external sense resistor. The resistor tolerance and the threshold window both count, so a one per cent resistor gives a current closer to three per cent.

How deep can it dim? 10,000 to 1 with a shunt FET across the string, 1000 to 1 with a PWM signal on the dimming pin, and 200 to 1 in the analogue range set by the adjustment pin.

Does it need an external compensation network? No. The constant off time peak current loop is set by the output voltage and the sense resistor, so there is no error amplifier compensation to calculate.

What is the minimum on time? 195 ns typical and 275 ns maximum. A high input voltage with a short string can reach that limit, and the converter then reduces its frequency instead of maintaining regulation.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.