TPS92512HVDGQR
Product Specifications
TPS92512HVDGQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS92512HVDGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS92512HVDGQR: a 60 V, 2.5 A step down LED driver with analog current adjust in a 10 pin MSOP
TPS92512HVDGQR is a step down constant current LED driver with an integrated 200 milliohm switch, a peak current mode loop and two dimming inputs in a HVSSOP (DGQ) body of 10 pins. It takes 4.5 V to 60 V in on the HV member and drives one string of LEDs at up to 2.5 A, with the current set by a voltage on the analog input rather than by a resistor, so brightness can be trimmed from a microcontroller or a thermistor network. The sense threshold is the analog input divided by six, which puts the full 300 mV at 1.8 V on that pin. Switching frequency is set from 100 kHz to 2 MHz by one resistor or by an external clock, the switch is 200 milliohm, and the current accuracy is plus or minus 5 per cent.
Order code and package
| TPS92512HVDGQR | HVSSOP body of 10 pins with a PowerPAD, 2500 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking 512H, active status in the package addendum |
| TPS92512DGQR | the 42 V member of the same family in the same body and on the same pinout, 2500 pieces on a large reel, marking 92512, which is the string used where the rail never exceeds 42 V |
| Small reel rows | the T suffix carries 250 pieces, and the .B row of the T string shows a large reel quantity on this family, so the packing column on the offer is the figure to trust |
| Analog input | 0 V to 1.8 V on the dimming pin, giving a sense threshold of 0 V to 300 mV, which is a linear current scale rather than a stepped one |
| PWM input | a separate logic level input for pulse dimming, stated to give a contrast ratio above 100 to 1 while the analog input gives above 10 to 1 |
| Clock | the internal oscillator can be overdriven by an external clock so several drivers run at one frequency and do not beat against each other |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 60 V on this HV member, with an absolute maximum of 65 V on the input and on the switch node |
| Output current | 2.5 A through the string, set by the analog input and the sense resistor, with plus or minus 5 per cent current accuracy |
| Sense threshold | 200 mV typical at a 1.2 V analog input, and 300 mV at 1.8 V, because the threshold is the analog voltage divided by six |
| Analog range | 180 mV to 1.8 V on the dimming pin for the specified window, which corresponds to 30 mV to 300 mV of sense threshold |
| Switch resistance | 200 milliohm typical at a 3.5 V gate drive, 232 milliohm in the table at 4.5 V in, which is the figure that sets the conduction loss at 2.5 A |
| Current limit | 6 A peak on the switch, cycle by cycle, which is a protection for the inductor and the string rather than a current setting |
| Switching frequency | 100 kHz to 2 MHz with a resistor, and 300 kHz to 2 MHz when an external clock is used, with a 51 ns minimum pulse width on that input |
| Minimum on time | 140 ns, which sets the maximum step down ratio at a given frequency and therefore the highest input voltage for a short string |
| Shutdown current | 11.5 microamp with the enable pulled low, which is what a luminaire that is switched off at the wall draws through the driver |
| Standby current | 337 microamp typical and 407 microamp maximum while enabled and not switching, which is the figure that matters for a dimmed to zero state |
| Undervoltage lockout | an adjustable lockout with a 1.12 V to 1.30 V threshold on its own pin and about 4 microamp of source current, so a divider sets the start and stop voltages |
| Boot rail | the gate drive is referenced to the switch node, with its own undervoltage lockout at 2.25 V rising and 1.99 V falling |
| Thermal | 66.7 C per watt junction to ambient in the 10 pin body, with a PowerPAD that has to reach the board copper for a 2.5 A string |
| Temperature | minus 40 C to 125 C junction over the electrical table |
How the two dimming inputs divide the work
| TPS92512HVDGQR | the 60 V member covered by this order code, 2.5 A, 10 pin HVSSOP with a PowerPAD |
| TPS92512DGQR | the 42 V member of the same family, same body, same pinout, same current, which is the string for a 24 V or 36 V fixture |
| Analog dimming | 0 V to 1.8 V on the dimming pin gives 0 V to 300 mV of sense threshold, which is a linear current scale rather than a stepped one |
| PWM dimming | a separate logic input with a contrast ratio above 100 to 1, while the analog input covers above 10 to 1 |
| Clock | the internal oscillator can be overdriven from 300 kHz to 2 MHz so several drivers do not beat against each other |
| Lockout | adjustable on its own pin with a 1.12 V to 1.30 V threshold, so the start and stop voltages are a divider choice |
| Current limit | 6 A peak cycle by cycle on the switch, which protects the inductor and the string rather than setting the operating current |
Points to check before this part goes on a BOM
The analog input is a current scale, not a dimmer switch. The sense threshold is the analog voltage divided by six, so the LED current follows the input linearly. That is what allows a thermistor network to fold the current back as a luminaire heats up, without any firmware in the loop.
The current accuracy is plus or minus 5 per cent at the sense point. The sense resistor tolerance sits on top of that, so a 1 per cent resistor gives a 6 per cent string, and a 5 per cent resistor gives a 10 per cent string that varies from unit to unit.
60 V is the input rating and the switch node sees the same stress. The absolute maximum on the switch node is 65 V, so a 48 V rail with a transient above that needs a clamp. The margin between 60 V operation and 65 V absolute is small on purpose.
There is no output capacitor in the usual sense. The converter drives a string of LEDs, and the output capacitor is a small ceramic that carries the ripple current rather than a bulk part. A large capacitor on the output changes the loop and the dimming response.
The PWM input is for dimming, not for shutdown. It chops the current at a duty cycle, and the contrast ratio above 100 to 1 is the figure quoted. A board that wants the driver off should use the enable or the lockout pin instead.
The lockout pin is adjustable and that is not a detail. With a divider on it, the driver starts and stops at voltages the board chooses, which is how a 48 V luminaire avoids restarting on a sag instead of holding the string on through it.
Why an LED driver is specified in current rather than in voltage
A string of LEDs has a forward voltage that moves with temperature and from batch to batch, so a constant voltage supply gives a current that moves with it. A driver that regulates current keeps the light output stable and keeps the string inside its rating, which is the whole reason this part exists.
The 2.5 A figure is the current the switch and the sense path can hold, and the actual string current is set lower by the sense resistor and the analog input. A 1 A string on this driver runs cooler and more accurately than the same string on a driver rated at 1 A, because the margin is in the switch.
What a 60 V input rating means for a luminaire
Street lighting and high bay fixtures often run a 48 V rail, and a 60 V driver leaves room for the tolerance and the transient without a pre-regulator. The same body in the 42 V version covers the 24 V and 36 V fixtures, which is why the two strings exist in one document.
Where this order code fits
a street light, a high bay fixture or a machine vision illuminator running one string from a 24 V to 48 V rail Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
How is the LED current set? By a sense resistor and the analog input. The sense threshold is the analog voltage divided by six, so 1.2 V on that pin gives 200 mV across the sense resistor and 1.8 V gives 300 mV.
What is the difference between this and the TPS92512DGQR? The input rating. This HV string takes 4.5 V to 60 V and the plain string stops at 42 V, with the same body, pinout and current rating.
Can several drivers run at one frequency? Yes. The internal oscillator can be overdriven by an external clock between 300 kHz and 2 MHz, which stops two drivers on one board from beating and making a visible flicker.
What happens if the string opens? The loop loses its feedback path and the switch hits the 6 A cycle by cycle limit, so the driver pulses rather than running at full duty. The output capacitor then sees the full rail, which is why its rating has to cover the input voltage.
Does the part need a heatsink? It needs board copper. The 10 pin body is 66.7 C per watt junction to ambient, and at 2.5 A the switch dissipates enough that the PowerPAD has to reach a copper area sized for the enclosure temperature.
How many pieces are on the reel? 2500 pieces on a large reel at moisture level 1, so the reel has unlimited floor life and does not need baking after it is opened.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.