Contact Us

TPS923650D1DRLR

Brand: Texas Instruments
Texas Instruments TPS923650D1DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS923650D1DRLR — Power Management & Signal Chain | Superb Automation

TPS923650D1DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS923650D1DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS923650D1DRLR: a boost driver in an eight pin SOT body for common cathode strings

The TPS923650D1DRLR is the 1 A member of the TPS92365x family, a non synchronous boost and buck boost LED driver that takes 4.5 V to 65 V in and switches a 300 milliohm low side FET with a 1.6 A cycle by cycle limit. The headline is the body: eight pins in SOT-5X3, which is 2.75 mm by 1.9 mm of tape pocket and fits where a boost driver normally does not. The D1 suffix means the DIM pin is read as a logic signal with a 100 ns minimum pulse, and the D2 version reads an analog voltage from 0 V to 2.2 V instead. The switching frequency of the DRL body is 400 kHz, while the DSG and DGN bodies of the same die run at 1 MHz, so the inductor value and the EMI signature follow the body choice rather than a resistor.

Common cathode connection is the other half of the story. Two strings that share a cathode can be driven from one boost stage with the return at the bottom of the stack, which keeps the LED board on one copper layer and the anode traces short. That is the arrangement in a 12 V battery lamp with six to eight emitters, and it is where the 65 V ceiling leaves room for a string that climbs to 40 V at the end of life.

Key electrical data on the page

Input range4.5 V to 65 V, UVLO rising 3.0 V to 3.4 V, falling 2.8 V to 3.2 V
Output current1 A class, cycle by cycle switch limit 1.4 A to 1.8 A on the 650 members
Switch300 milliohm low side NMOS, minimum on and off time 140 ns to 160 ns
Switching400 kHz in the DRL body, 1 MHz in the DSG and DGN bodies of the same die
Current sense200 mV at full scale on the DIM input at 2 V, 20 mV at 0.2 V for 200 to 1 analog dimming
Dimming100 ns PWM minimum pulse on the D1 version, analog range 0 V to 2.2 V on the D2 version
Internal rail5.15 V LDO, 20 mA limit, enough for the gate drive and a small external load

Package, marking and reel data

BodySOT-5X3 DRL, 8 pins, 2.75 mm by 1.90 mm tape pocket, 1.4 mm body height class
Reel4000 pieces on a 180 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q3
PocketA0 2.75 mm, B0 1.90 mm, K0 0.80 mm, carrier width 8.0 mm
Finish and moisturetin, level 1 at 260 C, unlimited floor life
Marking and grade2301 on the top, rated -40 C to 85 C ambient

Why the fast dimming pulse matters in a camera

A 100 ns minimum pulse at 400 kHz means the light can be on for one thousandth of a switching period and still produce a controlled current, which is what an exposure of 50 us needs when the sensor is reading a moving part. The control loop uses adaptive off time with peak current mode, so the current settles within a few cycles of the pulse start rather than over hundreds of microseconds. That is the difference between a strobe that lights the frame and one that lights the frame after the shutter has closed.

The 300 milliohm switch at 1 A dissipates 300 mW, and in an SOT body that is the thermal limit rather than the current rating. The thermal path is through the six copper pads, two of which are the switch source and the ground, so the copper under the body has to be treated as a heatsink and not as a signal node. A 1 MHz body halves the inductor value and therefore the board area, but it also doubles the switching loss; the 400 kHz DRL version is the one to pick when the string is long and the switch is on for most of the period.

Buyer questions on the TPS923650D1DRLR

Is a Schottky diode required? Yes. The part is non synchronous, so the freewheel diode carries the inductor current during the off time. It has to be rated above the string voltage with margin, and its forward drop is a direct efficiency term at 1 A.

Can two strings be driven from one stage? Two strings that share a cathode can be placed in series in the same loop, which is what the common cathode connection is for. Strings that need independent current control need one driver per string.

What is the difference between the D1 and D2 bodies? Only the DIM pin. D1 reads a logic pulse with a 100 ns floor for PWM dimming, D2 reads an analog voltage from 0 V to 2.2 V for 200 to 1 analog dimming. The order code carries the choice in the D1 or D2 position, and the reel quantity is the same.

Buying this part through a component supplier

A part that exists in four bodies is a procurement opportunity and a documentation risk at the same time, because the same logical line can arrive in a DRL, DGN or DSG package with a different reel count. The pin to pin cross reference is the page that shows which of the four bodies share a footprint and which do not. For build programmes that already carry this driver, date code management keeps the reels from two different bodies separate in the store, so a pick and place program is never loaded with the wrong tape pitch.