Contact Us

TPS92200D2RXLR

Brand: Texas Instruments
Texas Instruments TPS92200D2RXLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92200D2RXLR — Power Management & Signal Chain | Superb Automation

TPS92200D2RXLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92200D2RXLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92200D2RXLR: a 99 mV reference is what lets a 1.5 A buck sit in a 1.5 mm by 2 mm body

The TPS92200D2RXLR is a synchronous buck LED driver that takes 4 V to 30 V in and pushes up to 1.5 A through a string, with the high side and low side switches inside the package at 150 milliohm and 90 milliohm. The number that decides how the rest of the circuit looks is the feedback reference: 99 mV, specified between 96 mV and 102 mV over the full temperature range. A 350 mA string therefore needs a sense resistor of 283 milliohm, and that resistor burns 35 mW instead of the 175 mW it would burn against a 500 mV reference. In a camera housing with no airflow that difference is the difference between a board that stays inside its enclosure rating and one that does not.

The switching node runs at 1 MHz nominal, 0.8 MHz to 1.2 MHz over part spread, which puts the inductor at 10 uH to 22 uH for most strings and keeps the ripple current inside 30 percent. Peak current mode control with full internal compensation means there is no external compensation network to calculate, and the 99 percent maximum duty cycle lets the part hold regulation when the string voltage comes within a volt of the input, which happens on a 24 V rail driving six white LEDs at 3.3 V each.

Key electrical data on the page

Input range4 V to 30 V, UVLO rising 3.5 V to 3.9 V and falling 3.3 V to 3.7 V with 0.2 V of hysteresis
Output current1.5 A continuous, high side limit 2.9 A to 4 A, low side sourcing 2.4 A to 3.6 A
Feedback99 mV typical, 96 mV to 102 mV across the range, over voltage threshold at 140 mV
Switches150 milliohm high side and 90 milliohm low side at 5 V or more at the input
Switching1 MHz nominal, 0.8 MHz to 1.2 MHz spread, minimum on time 75 ns to 100 ns
DimmingD2 version takes PWM duty on the DIM pin from 1 percent to 100 percent, minimum on 300 ns
Quiescent and shutdown0.5 mA to 1 mA operating, 1 uA typical and 3 uA maximum in shutdown

Package, marking and reel data

BodyVQFN-HR RXL, 6 pins, 1.50 mm by 2.00 mm, wettable flank on the side pads
Reel3000 pieces on a 180 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q1
PocketA0 1.75 mm, B0 2.25 mm, K0 1.00 mm, carrier width 8.0 mm
Finish and moisturetin, level 2 at 260 C peak, one year floor life
Marking and grade1JP on the top, rated -40 C to 85 C junction

Where the D2 dimming version belongs

The D1 and D2 versions differ only in how the DIM pin is read. D1 takes an analog voltage from 0.65 V to 1.2 V and scales the reference across that window. D2 reads the duty cycle of a logic signal and scales the reference from 1 percent to 100 percent, which means a camera or a vision system can hand the driver the same strobe signal it already sends to the sensor, with no digital to analog converter in between. The 1 percent floor is 1 mV of reference and about 3.5 mA of LED current on a 283 milliohm sense resistor, so the dimming range is roughly 400 to 1 in current terms.

Two timings matter to a machine vision build. The DIM minimum on time to enable the device is 190 ns typical and 300 ns maximum, so a 300 ns strobe is the shortest pulse that will produce light rather than nothing. The minimum off time is 36 ms, and a low longer than that shuts the device down rather than dimming it, which is the behaviour a user wants when the trigger stops: the part goes quiet instead of holding the output capacitor charged. Automotive and CCTV integrators use exactly this pair of numbers to set the blanking window on the sensor, and 850 nm and 940 nm IR emitters at 1 A are the most common loads we see on this order code.

Buyer questions on the TPS92200D2RXLR

Can the same sense resistor cover two brightness levels? No, the reference is fixed at 99 mV and the resistor sets the full scale current. Brightness changes come from the duty cycle on the DIM pin. A build that needs two hard wired levels uses two resistors with a selector, or the D1 version with an analog voltage.

Is a bootstrap capacitor needed? Yes, between BOOT and SW, and it is the one component the internal switch pair cannot do without. It has to be a low inductance ceramic placed within a few millimetres of the two pins, and it sees the full input voltage.

What happens when the LED string opens? The protection set includes LED open, LED+ short to ground, LED short and sense resistor open or short, and each one ends in a retry of 512 switching cycles followed by 60 ms off. The part does not latch, so a cable that is plugged back in recovers without a power cycle.

Buying this part through a component supplier

Panasonic, Osram and Lumileds strings are usually specified together with the driver, and the driver is often the line that holds up a build because it is a single source part with a long lead time. The power management cross reference lists the 30 V buck drivers we can compare by pin count and reference voltage, which is the fastest way to see whether a second source exists before a schedule moves. When the reel is short and the build date is fixed, component lead time solutions covers partial reels, date code control and the packing change from 3000 to a cut tape quantity.