Contact Us

TPS92200D2DDCR

Brand: Texas Instruments
Texas Instruments TPS92200D2DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92200D2DDCR — Power Management & Signal Chain | Superb Automation

TPS92200D2DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92200D2DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92200D2DDCR: a 4 V to 30 V, 1.5 A synchronous buck LED driver with analog dimming

TPS92200D2DDCR is a 1.5 A synchronous buck LED driver with a 99 mV feedback threshold in a SOT-23-THIN (DDC) body of 6 pins. The DDC body is 1.60 mm by 2.90 mm with six pins, and the D2 in the string is the dimming variant: it takes a PWM signal on DIM and turns the duty cycle into an analog reference, from 1 percent to 100 percent, rather than switching the LED current on and off. The D1 variant does the opposite and accepts either a PWM or an analog level on the same pin.

Order code and package

TPS92200D2DDCRSOT-23-THIN (DDC), 6 pins, 3000 piece large reel, MSL level 2 at 260 C with a one year floor life
TPS92200D2RXLRthe same die in the VQFN-HR body, 1.50 mm by 2.00 mm, 3000 piece large reel
TPS92200D1DDCRPWM and analog dimming from a level or a duty cycle on DIM, same body and same reel
Addendum notethe orderable table in SLVSER4B prints the package column shifted between the DDC and RXL rows, so the suffix rather than the row order is what identifies the body
Pin outBOOT, FB, GND, DIM, SW, VIN in the six pin body, with FB as the LED current sense input
DocumentSLVSER4B, May 2020 and revised January 2022, with the VQFN-HR body added in revision A

Electrical parameters that decide the application

Input range4 V to 30 V operating, with a 3.7 V rising and 3.5 V falling undervoltage lockout and 200 mV of hysteresis
Output current1.5 A continuous through an integrated 150 mOhm high side and 90 mOhm low side FET, both specified at 5 V or more of input
Feedback threshold99 mV plus or minus 3 mV at a 3.3 V DIM level, which is the number that sets the sense resistor: 0.15 Ohm gives 660 mA and 0.1 Ohm gives 990 mA
Dimming rangethe D2 turns a DIM duty cycle of 1 percent to 100 percent into a reference from 1 mV to 99 mV, so the current range is about 100 to 1
Dimming thresholds0.3 V low and 0.65 V high on DIM, with a 1.2 V analog range on the D1 variant
Timinga DIM on time of at least 190 ns to 300 ns and a DIM off time of at least 36 ms before the device treats the signal as a shutdown command
Frequency1 MHz fixed with peak current mode control and full internal compensation, and a maximum duty cycle of 99 percent
Current limithigh side 2.9 A to 4 A, low side sourcing 2.4 A to 3.6 A, low side sinking 1.4 A to 2.4 A
Supply current1 uA typical and 3 uA maximum in shutdown with DIM at 0 V, and about 1 mA while operating
ProtectionLED open, LED plus short to ground, LED to LED short, sense resistor open and short, all with auto-retry, plus thermal shutdown at 165 C with 15 C of hysteresis
Open load behaviourthe FB overvoltage comparator at 140 mV stops the converter when the LED string opens and retries after the fault clears

Family variants and how they differ

D1 against D2D1 dims from an analog level between 0.65 V and 1.2 V or from a PWM duty, D2 dims from the duty cycle only and reaches deeper, down to 1 percent
DDC against RXLSOT-23-THIN at 1.60 mm by 2.90 mm against VQFN-HR at 1.50 mm by 2.00 mm, same electrical behaviour, different thermal pad
No inductorless variantthis is a buck, so the inductor and the freewheel path are inside the part but the inductor is still external
Against a constant current sourcethe part regulates the LED current from the FB voltage, so a 99 mV sense threshold keeps the sense resistor dissipation small
No spread spectrumthe 1 MHz clock is fixed, so the switching band cannot be moved away from a sensitive receiver

Points to check before this part goes on a BOM

The 99 mV feedback threshold is the reason this part exists in a small camera or a machine vision board. A 1 A string with a 0.1 Ohm sense resistor dissipates 100 mW, and the same current with a 1 V threshold would dissipate 1 W, which is more than the LED driver package can carry. Tolerance on that 99 mV is plus or minus 3 mV, so the current accuracy follows from the resistor tolerance rather than from the part, and a 1 percent sense resistor keeps the string current inside 4 percent.

The D2 dimming path is a duty cycle to reference converter, so the dimming resolution is set by the DIM signal rather than by an internal DAC. A 1 kHz PWM with a 1 percent minimum duty is a 10 microsecond pulse, and the part's own 190 ns to 300 ns minimum on time means the low end of the range is limited by the controller feeding DIM, not by the driver. A 36 ms off time is treated as a shutdown, which is why a dimming source that can hold DIM low for longer than that will switch the rail off rather than dim to zero.

Thermal is the binding constraint in a sealed camera housing. The 150 mOhm high side and 90 mOhm low side in a 1.60 mm by 2.90 mm body give roughly 0.24 W of conduction loss at 1 A with a 12 V input and a 3.3 V string, and the switching loss adds to it. The VQFN-HR version exists for exactly this reason: the same die in a body with a thermal pad is the difference between a board that holds 1.5 A in still air and one that folds back.

The protection set is aimed at the failure modes a light engine actually has. An open string drives FB to zero and the converter runs to its overvoltage comparator at 140 mV, a short from LED plus to ground pulls FB up and trips the same comparator, and a shorted LED inside the string raises the forward voltage and is caught by the same window. Every one of those faults retries, so a transient does not need a power cycle.

What 4 V to 30 V really buys

A 24 V industrial rail with a 30 V clamp is inside the part's operating range, and a 12 V rail with a 20 percent transient is comfortable. The 3.7 V lockout is what allows a single cell lithium pack to drive a 3 V string, and the 99 percent maximum duty means the part keeps regulating when the input falls close to the string voltage.

The other side of the range is dropout: at 30 V in and a 3.3 V string the duty cycle is about 11 percent, and the minimum on time of the high side switch is what limits the switching frequency that can be used at that ratio. The part runs at 1 MHz, so a high input and a low string is the case to check on a bench rather than in a spreadsheet.

Dimming depth against perceived light

A 100 to 1 current range is about 40 dB of dimming, which is enough for a display backlight or an IR illuminator that has to run at low power for eye safety, but not enough for a lamp that claims 1000 to 1. The D2 variant gets the deeper range of the two, and the limit is the 1 mV minimum reference against the input offset of the FB comparator.

Where this order code fits

It drives infrared and white LED strings in video surveillance cameras, facial recognition terminals, stage lighting and general industrial illumination. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What is the difference between the D1 and the D2? The D1 accepts either an analog level from 0.65 V to 1.2 V or a PWM duty on DIM, and the D2 converts a PWM duty from 1 percent to 100 percent into the reference. The D2 reaches deeper dimming, the D1 is more flexible about the source.

How is the LED current set? By the sense resistor: 99 mV divided by the resistance. A 0.1 Ohm resistor gives 990 mA and a 0.15 Ohm resistor gives 660 mA, with the accuracy dominated by the resistor.

Does a long low period on DIM switch the part off? Yes. A DIM off time longer than 36 ms is treated as a shutdown command, so a dimming source has to keep the pulse train above that rate.

Which body should a thermally tight board use? The RXL VQFN-HR, because the same die in a body with a thermal pad runs cooler at 1.5 A than the six pin SOT-23-THIN.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.