Contact Us

TPS82740BSIPR

Brand: Texas Instruments
Texas Instruments TPS82740BSIPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS82740BSIPR — Power Management & Signal Chain | Superb Automation

TPS82740BSIPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS82740BSIPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS82740BSIPR: 360 nA of quiescent current in a 6.7 mm square module

The TPS82740BSIPR is a step down converter module whose quiescent current is 360 nA typical, a figure that puts the supply of a sleeping product below the self discharge of the cell it runs from. The B variant covers 2.6 V to 3.3 V in 100 mV steps selected by three pins, delivers up to 200 mA, and takes 2.2 V to 5.5 V at the input, which includes a lithium thionyl chloride cell, two alkaline cells and a USB port. The whole solution sits in 6.7 mm squared with a 1.1 mm profile.

Inside the module there is also a load switch with 0.6 Ohm of on resistance, controlled separately, so a subsystem can be powered from the same rail without an external transistor. The converter enters a no ripple 100 percent mode when the battery approaches the output voltage, which stops the switching and connects the input to the output rather than letting the ripple grow as the duty cycle reaches its limit.

Key electrical data for the B variant

Input range2.2 V to 5.5 V, covering a coin cell, two alkaline cells or a USB rail
Output2.6 V to 3.3 V in 100 mV steps, selected by three pins during operation
Output current200 mA, with a 150 mA typical soft start limit
Quiescent current360 nA typical, which is the lowest in this family
Load switch0.6 Ohm on resistance, separately enabled, for a switched subsystem rail
Mode behaviourno ripple 100 percent mode as the battery approaches the output voltage
PackageMicroSiP, 2.30 mm by 2.90 mm, 9 bumps, 1.1 mm profile

Package, marking and reel data

BodyuSIP, 9 bumps, 2.30 mm by 2.90 mm, marking E8 for the B variant
Reel3000 pieces with the R suffix on a 178 mm reel, 250 with the T suffix
Tape4.0 mm pitch, 8.0 mm width, quadrant Q2
Handlingopen frame module, picked like an 0805 component on standard equipment
Siblingthe A variant covers 1.8 V to 2.5 V with the same body and the marking E7

Where a 360 nA supply changes a product

Utility meters, water and gas sensors, asset trackers, medical patches and remote monitoring nodes are the products this module is built for. In those products the battery is expected to last five or ten years, and the sleep current of the supply is one of the few terms a board team still controls. At 360 nA the regulator disappears from the budget; at 3 uA it would be a quarter of it.

The selectable output is the second convenience. A radio that wants 3.3 V and a sensor that wants 2.8 V can share one module if the pins are driven at the right moments, and the load switch gives the sensor its own gated rail without another part. What the module does not do is step up, so a product with a 1.8 V cell has to choose a different family member or a boost converter. The 100 percent mode is the other half of the battery story: as a lithium cell falls toward 2.8 V the module stops switching and passes the cell voltage through, so the product keeps running below the point where a boost converter would have started drawing more current than it delivered. That matters in a meter that has to send one last report when the cell is nearly flat, which is exactly the report a utility reads first when a unit goes quiet.

Buyer questions on the TPS82740BSIPR

How are the output voltages selected? Three pins, VSEL1 to VSEL3, set the output in 100 mV steps and can be changed while the device runs. That is what lets one module serve a 2.6 V and a 3.3 V load at different times.

What is the difference between the A and B variants? The output range only: 1.8 V to 2.5 V on the A, 2.6 V to 3.3 V on the B. The body, the pin out and the quiescent current are the same, and the marking differs by one character.

Does the load switch need an external capacitor? The module carries its own input and output capacitance, so the switch output needs only the decoupling of the subsystem it feeds. A short trace and a local capacitor keep the transient clean.

Buying this module through a component supplier

The A and B variants differ by one character in the order code and one character on the package, which is exactly the kind of pair that gets mixed in a store. Our power management cross reference lists both with their marking. For a metering program with a ten year life, component obsolescence management covers the last time buy arithmetic.