TPS7B92050DBVR
Product Specifications
TPS7B92050DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B92050DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B92050DBVR: 5 V at 300 mA and 1.8 uA of standing current
The TPS7B92050DBVR is a 300 mA regulator with a fixed 5 V output, a 2.5 V to 40 V input window and a quiescent current of 1.8 uA typical at no load. That figure is three orders of magnitude below a conventional 40 V regulator and it is the reason the part exists: a module that sits connected to a battery for months can afford a rail that draws microamps, and cannot afford one that draws milliamps. The DBV suffix is the five pin SOT-23 body at 2.9 mm by 2.8 mm.
The trade for that quiescent current is dropout. At 300 mA the part needs about 1.1 V of headroom, so a 5 V output wants 6.1 V or more at the input, and at 50 mA the figure falls to 440 mV. The output window printed for the 5 V row is 4.75 V to 5.25 V across the temperature range, the output capacitor range is 1 uF to 47 uF, and an internal soft start limits the inrush when the rail comes up.
Key electrical data for the 5 V part
| Input range | 2.5 V to 40 V, which covers a 12 V or 24 V bus with transients |
| Output | 5.0 V fixed, printed window 4.75 V to 5.25 V over the temperature range |
| Output current | 300 mA, with a foldback current limit and a short circuit limit |
| Quiescent current | 1.8 uA typical at no load, the figure that makes the part useful |
| Dropout | 440 mV at 50 mA, 1.1 V at 300 mA, so the headroom has to be planned at full load |
| Output capacitor | 1 uF to 47 uF effective, stable across that range |
| Protection | internal soft start, foldback current limit, thermal shutdown |
Package, marking and reel data
| Body | SOT-23 DBV, 5 pins, 2.90 mm by 2.80 mm |
| Reel | 3000 pieces, large tape and reel |
| Finish and moisture | SN, level 1, 260 C peak reflow, unlimited floor life |
| Marking | 37GH |
| Family | 1.8 V, 3.3 V, 5.0 V and 12 V fixed rows in the same body, all 3000 per reel |
Where 1.8 uA decides the architecture
Battery powered sensors, utility meters, smoke detectors, trackers and any always-on module that has to last a season on one cell are the natural homes. In those products the sleep current of the whole board is often set by its regulator, and a part that draws 1.8 uA allows the rest of the board to spend its budget on the radio and the sensor instead of on housekeeping. The 40 V input also means the same part can hang on a 24 V industrial bus without a pre regulator.
The 300 mA rating is where the arithmetic needs care. A radio that transmits in bursts draws its peak from the output capacitor and the regulator supplies the average, so the 1.1 V of dropout at 300 mA only matters during the burst. A board that runs 300 mA continuously from a 6 V rail is on the edge, and one that runs it from a 24 V rail is a thermal problem rather than a dropout problem. The output capacitor is what bridges the two cases, and a 10 uF ceramic covers a burst of tens of milliseconds without the rail moving. The quiescent current does not change with the output capacitor, so the buffer costs nothing in sleep. What it does change is the start-up inrush, which the internal soft start keeps bounded and which a larger capacitor would otherwise multiply.
Buyer questions on the TPS7B92050DBVR
How is 1.8 uA possible in a 40 V part? The pass element and the bias circuit are biased from the output rather than from the input, so the standing current does not scale with the input voltage. That is also why the dropout is higher than a conventional part at full load.
Does the part need a minimum output capacitor? 1 uF effective is the floor and 47 uF the ceiling. A 1 uF ceramic is enough for a light load, and the larger values help a pulsed load without destabilising the loop.
What happens during a short circuit? The foldback limit reduces the current rather than holding it at the peak value, so the part runs cooler into a fault. It recovers to regulation when the short is removed, without a power cycle.
Buying this regulator through a component supplier
Four voltage options in one SOT-23 body means the reel label is the only thing standing between a 5 V build and a 3.3 V one. Our power management cross reference lists the codes by output. For a meter or tracker program that runs for years on one cell, safety stock planning is where the buffer quantity for a long life product gets set.