TPS7B8133QDRVRQ1
Product Specifications
TPS7B8133QDRVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B8133QDRVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B8133QDRVRQ1: 3.3 V fixed, 150 mA, 40 V automotive LDO in a 6 pin WSON body
TPS7B8133QDRVRQ1 is a fixed 3.3 V automotive low dropout regulator that keeps its quiescent current in the microamp range so a battery connected module stays alive with the ignition off in a WSON body of 6 pins. It runs from 3 V to 40 V with a 45 V transient rating, supplies 150 mA, holds 1.5 per cent accuracy over line, load and temperature, and draws 2.7 uA typical at light load against 300 nA in shutdown. The DRV body measures 72.8 C per watt junction to ambient on a JEDEC board, which is the number that decides whether the part carries the dissipation or the board does.
Order code and package
| TPS7B8133QDRVRQ1 | 6 pin WSON (DRV), 2.00 mm by 2.00 mm, 3000 pieces on a large reel, marking 1X2H, moisture level 2 with a one year floor life |
| TPS7B8133QWDRVRQ1 | same die in the wettable flank WSON, 2500 pieces on a large reel, tin plating, moisture level 1 unlimited, the row to name when the assembly line needs a visible solder fillet |
| TPS7B8133QDGNRQ1 | 8 pin HVSSOP (DGN), 3.00 mm by 3.00 mm, 2500 pieces on a large reel, 63.9 C per watt junction to ambient |
| TPS7B8133QKVURQ1 | 5 pin TO-252 (KVU), 6.10 mm by 6.60 mm, 2500 pieces on a large reel, 38.8 C per watt, moisture level 3 with a 168 hour floor life |
| Temperature grade | minus 40 C to plus 125 C ambient and minus 40 C to plus 150 C junction, AEC-Q100 grade 1, HBM class H3A and CDM class C4B |
Electrical parameters that decide the application
| Input voltage | 3 V to 40 V operating, 45 V transient, the enable pin rated to the same 40 V |
| Output voltage | 3.3 V fixed, 1.5 per cent accuracy over line, load and the full temperature range |
| Output current | 150 mA maximum continuous |
| Quiescent current | 2.7 uA typical at light load and 4.5 uA maximum on the front page, while the EC table prints a 1.9 to 6.5 uA window for the DGN body at zero load |
| Shutdown current | 300 nA typical with the enable pin pulled low |
| Dropout voltage | 200 mV typical and 390 mV maximum in the DGN row, while the 540 mV maximum on the front page belongs to the 5 V member |
| Current limit | 180 mA minimum, 510 mA typical and 690 mA maximum with the output pulled to 90 per cent of its set value |
| Undervoltage lockout | 200 mV of hysteresis, the curve in the document puts the falling release near 1.95 V |
| Thermal shutdown | 175 C junction in the electrical table, while the mode table uses 160 C for the same event |
| Output capacitor | 1 uF to 200 uF ceramic, stable across 0.001 ohm to 5 ohm of ESR |
Which package and which family member
| 2.5 V member | TPS7B8125, where dropout is not specified at all because the minimum input voltage limits take over below 3 V |
| 5 V member | TPS7B8150, and the 540 mV maximum dropout figure on the front page is quoted for this row rather than for the 3.3 V part |
| W suffix | wettable flank, which exists because a 2 mm by 2 mm body with no visible fillet is hard to inspect after reflow |
| TO-252 body | for boards that have to burn the dissipation in the package instead of in the copper, 38.8 C per watt against 72.8 on the WSON |
| Second row per code | the vendor addendum repeats each order code with an .A suffix and a different reel quantity, so the packing figure has to be read per row |
| Non automotive part | the same silicon without the Q1 suffix is a separate document with a different temperature grade and is not interchangeable in a qualified build |
Points to check before this part goes on a BOM
The quiescent current is the whole reason for this part to exist, and it comes with three different numbers that mean three different things. The 2.7 uA typical applies at light load with the regulator enabled and regulating. The 4.5 uA maximum on the front page is the guarantee over temperature for the same condition. The 1.9 to 6.5 uA window in the electrical table is the spread at zero load on the DGN body across the whole grade. A module that has to survive a parked car for a month budgets the maximum figure, not the typical one.
The shutdown row is the other half of the same budget. At 300 nA typical with the enable pin low, a 60 Ah battery loses well under a milliamp hour a month to this regulator, which is the difference between a quiescent drain the customer can live with and one that shows up as a warranty complaint. The catch is that the enable pin is not a logic input that can be left floating; it is rated to 40 V so it can be tied to the input on an always on rail, and it has to be driven deliberately on a switched rail.
Dropout depends on which output voltage the reader is looking at, and the document does not spell that out in one place. The 3.3 V member in the DGN body is specified at 200 mV typical and 390 mV maximum at 150 mA. The 540 mV maximum on the front page belongs to the 5 V member. An engineer sizing a 3.3 V rail against a 3.0 V cold crank floor has to add the 390 mV to 3.3 V, which lands at 3.69 V, and that is above the crank floor, so the rail sags in a cold crank unless the load is small enough for the regulator to be in dropout and still acceptable.
The current limit row is a window rather than a number. A 150 mA part that limits anywhere between 180 mA and 690 mA will either protect a small trace or let a short draw a good deal more than the label suggests, and the 690 mA top of the window is what a shorted harness actually sees for a few microseconds before the thermal shutdown catches up. Fusing and trace width should be sized against the maximum, not the typical.
The four package rows are not interchangeable in production. The WSON has moisture level 2 with a one year floor life and the TO-252 has level 3 with 168 hours, which means an opened reel of TO-252 parts has to be baked or used inside a week. The wettable flank WSON is the only P option for a line that inspects solder joints by camera, and it ships plated in tin rather than nickel palladium gold, which changes the solder profile as well as the shelf life.
The wettable flank row also carries the tighter moisture classification, level 1 unlimited, which is unusual for a plastic body and is worth knowing when a program has to hold stock across a long build. Buying the W version for a few cents more can remove a bake step from the line entirely, and the only cost is that the flank adds a little width to the land pattern.
The second row per order code in the vendor addendum is a trap for anyone copying a part number into a purchase order and assuming a reel quantity. The same string appears twice with 3000 and 2500 pieces, and the difference is not a typo in one row but two separate packing options. A purchase order that states the part number alone can be filled either way, so the reel size has to be written on the order.
Thermal shutdown appears twice in the document with two different numbers, 175 C in the electrical table and 160 C in the state table. The second is the point where the regulator stops regulating, the first is the junction limit. A board that runs the part near its dissipation ceiling will see the output fall out of regulation before the junction reaches the absolute figure, and that is the behaviour a thermal soak test will show.
Where this order code fits
It sits in body control modules, head units, CAN and LIN transceiver standby rails and battery management sense chains, anywhere a 12 V battery stays connected while the module is asleep and the regulator has to be the smallest drain on the net. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Date Code Management page.
Questions buyers ask
Can this part run straight from a 12 V automotive rail? Yes. The input range reaches 40 V with a 45 V transient rating, which covers a load dump clamp at the module input as long as the clamp holds below 45 V. The 150 mA output is what limits the application, not the input voltage.
What is the real quiescent current over temperature? 4.5 uA maximum on the front page for light load, with the electrical table showing a 1.9 to 6.5 uA spread at zero load on the DGN body. Budget the maximum for a standby calculation.
Does the 3.3 V version have the same dropout as the 5 V version? No. The 3.3 V member is 200 mV typical and 390 mV maximum in the DGN body, and the 540 mV maximum printed on the front page is the 5 V member.
Which package should a new board use? The WSON for size, the HVSSOP when the board needs the lower thermal resistance of a wider body, and the TO-252 when the dissipation has to leave through the package tab. The wettable flank WSON is the choice when joints are inspected by camera.
Is the part protected against a shorted output? Yes. Current limit acts between 180 mA and 690 mA, and thermal shutdown takes over if the fault holds. Both are non latching, so the rail recovers when the fault clears.
What reel quantity is on the order code? 3000 pieces on the plain DRV row and 2500 on the .A row of the same string. The reel size has to be named on the purchase order.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.