Contact Us

TPS7B8133DRVR

Brand: Texas Instruments
Texas Instruments TPS7B8133DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B8133DRVR — Power Management & Signal Chain | Superb Automation

TPS7B8133DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B8133DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B8133DRVR: automotive 3.3 V, 150 mA off-battery regulator with 2.7 uA quiescent current

TPS7B8133DRVR is a linear regulator built to stay connected to the battery permanently and still draw microamps when the vehicle is parked in a WSON (DRV) body of 6 pins. It takes 3.0 V to 40 V in with a 45 V transient rating, delivers 150 mA at 3.3 V with 1.5 per cent accuracy over temperature, and draws 2.7 uA typical and 4.5 uA maximum at light load, which is the number that decides how long a parked vehicle can leave the module connected.

Order code and package

Ordering stringTPS7B8133DRVR, the fixed 3.3 V output in the 6 pin WSON
BodyWSON 6 pin, 2.00 mm by 2.00 mm, with the thermal pad on the underside
Package familyDGN 8 pin HVSSOP at 3 by 3 mm, DRV 6 pin WSON at 2 by 2 mm including a wettable flank version, KVU 5 pin TO-252 at 6.1 by 6.6 mm
Thermal resistance72.8 degrees per watt junction to ambient in the DRV body, 63.9 in the DGN body, 38.8 in the TO-252
QualificationAEC-Q100 grade 1, minus 40 to 125 degrees ambient and minus 40 to 150 degrees junction
Fixed outputs5.0 V, 3.3 V and 2.5 V, this page being the 3.3 V member
Functional safetyDocumented as functional safety capable, with the documentation needed for a safety case available from the vendor

Electrical parameters that decide the application

Input range3.0 V to 40 V operating, 45 V transient, with the output in regulation from the dropout floor up to 40 V
Output current150 mA maximum, with the current limit window at 180 to 690 mA and 510 mA typical
Quiescent current2.7 uA typical at light load in the DRV and KVU bodies, 4.5 uA maximum; the DGN body is 1.9 uA typical and 6.5 uA maximum
Shutdown current300 nA typical, 1 uA maximum, with the enable pin low
Accuracyplus or minus 1.5 per cent over line, load and temperature, which is tighter than the 2 per cent of the previous generation of off-battery parts
DropoutFor the 3.3 V output at 150 mA the maximum sits between 650 and 675 mV depending on body; the 5 V member quotes 540 mV maximum in the DGN body
Line and load regulation10 mV over 6 V to 40 V in and 1 mA to 150 mA in the DGN body, 20 mV in the DRV and KVU bodies
Ripple rejection60 dB at 100 Hz with 0.5 V peak to peak of ripple, 10 mA of load and a 2.2 uF output capacitor
Undervoltage detection2.7 V typical with 200 mV of hysteresis, so the output turns off before the regulator loses control
Enable thresholds0.7 V maximum for a low, 2.0 V minimum for a high, 10 nA of input current, so a 3.3 V GPIO drives it directly
Output capacitorStable with 1 uF to 200 uF of ceramic anywhere from 1 milliohm to 5 ohm of ESR, which covers the cheap small case sizes
Thermal shutdown175 degrees junction, with the part restarting when the die cools

Family variants and how they differ

DRV against DGNThe 6 pin WSON is smaller and has the higher thermal resistance. The 8 pin HVSSOP has an extra pin brought out and a lower junction to ambient figure, which matters at 150 mA with a 40 V input
TO-252 optionThe KVU body is the through hole friendly one at 38.8 degrees per watt. It is the right choice when the board has to survive 40 V in and 150 mA continuously in a hot enclosure
Wettable flankThe DRV body is offered with wettable flank plating, which lets an automated optical inspection see the solder joint on the side of the package. Automotive lines that require that inspection should order the wettable flank row
TPS7B81 against the wider familyThe same family carries 5 V and 2.5 V fixed versions and a 450 mA member. The 150 mA part on this page is the lowest quiescent one
Enable and shutdownThe enable pin is a true shutdown, not a standby. It drops the part to 300 nA and the output goes to zero, so a module can be switched off by a microcontroller rather than by a FET
ProtectionShort circuit and overcurrent limit at 180 to 690 mA, plus thermal shutdown. There is no reverse battery protection inside the part, so a series diode or a P-channel FET is still needed on a battery rail

Points to check before this part goes on a BOM

Quiescent current differs by package: 2.7 uA typical in the DRV and KVU bodies against 1.9 uA typical in the DGN. A specification quoted without the body is not a specification.

The 40 V rating is an operating figure and 45 V is the transient. A load dump on a 12 V system reaches far higher than 45 V without a central clamp, so the clamp is part of the system, not part of the regulator.

There is no reverse polarity protection inside. Jump starting a vehicle with the leads reversed puts the battery voltage across the part backwards, and a series blocking element is the only defence.

The dropout figures are quoted at 150 mA and the maximum values move with package. At 3.3 V out from a 12 V battery the dropout never binds, but a cold crank down to 3.5 V does, and the output falls out of regulation once the input drops below output plus dropout.

The 1.5 per cent accuracy applies over line, load and temperature, which is what an automotive ECU needs for a CAN transceiver supply. A 3 per cent part forces a wider transceiver supply window and a larger capacitor.

Stability is specified across 1 uF to 200 uF of ceramic with ESR between 1 milliohm and 5 ohm. That range covers parts that are easy to buy, and it also means a tantalum or an aluminium electrolytic can be used in a repair without a stability check.

Why an off-battery regulator is a different part from an LDO

A normal low dropout regulator is judged on dropout, noise and cost. An off-battery regulator is judged on what it draws when the load is zero. A parked car can leave a module connected for weeks, and every microamp of quiescent current becomes a fraction of the battery capacity that is gone before the engine turns over.

That is why the quiescent current here is 2.7 uA rather than the 50 to 100 uA of a general purpose part, and why the enable pin is a real shutdown at 300 nA. The cost of the low current is a slower transient response and a modest 60 dB of ripple rejection at 100 Hz, which is a trade an always-on rail can accept.

Where this order code fits

Anything that stays powered after the ignition key is out: body control modules, door and seat modules, gateway microcontrollers, CAN and LIN transceivers in standby, and always-on sensor nodes on a 12 V battery. The input is the raw battery rail, which means load dump, reverse connection during service and cold crank all arrive at the same pin, so the 40 V rating and the 45 V transient figure are the reason the part is specified rather than a generic LDO. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the OEM Procurement page.

Questions buyers ask

Is this part a replacement for a TPS7B69xx? They share the 40 V class and the 150 mA rating but not the quiescent current: the TPS7B69xx family draws roughly 15 uA typical, this one 2.7 uA. The board can usually take the newer part, but the stability range and the dropout figures differ, so the output capacitor should be checked against the newer document.

What happens during a cold crank down to 3 V? The part keeps regulating until the input falls below output plus dropout, then the output follows the input down. The 2.7 V undervoltage detection turns the output off with 200 mV of hysteresis so a module does not oscillate at the boundary.

Can two of these be paralleled for 300 mA? No. Linear regulators do not share current, and the one with the higher set point takes the whole load. A 450 mA member of the same family is the correct answer.

Does the output capacitor type matter? Ceramic from 1 uF to 200 uF with ESR between 1 milliohm and 5 ohm is stable. The upper capacitance limit exists because the enable ramp and the short circuit recovery change with a very large output capacitor.

Which body should a new board use? The DRV body for space, the DGN body when the board runs hot, the KVU body when the assembly is through hole or the thermal margin is thin. All three carry the same silicon.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.