Contact Us

TPS7B6950QDBVRQ1

Brand: Texas Instruments
Texas Instruments TPS7B6950QDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B6950QDBVRQ1 — Power Management & Signal Chain | Superb Automation

TPS7B6950QDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B6950QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B6950QDBVRQ1: 5.0 V fixed, 40 V input, 150 mA automotive LDO, 15 microamp quiescent, SOT-23-5

TPS7B6950QDBVRQ1 is a fixed 5.0 V linear regulator rated 150 mA that works from a 4 V to 40 V input, survives 45 V transients and draws 15 microamp with no load in a SOT-23 body of 5 pins. The part is qualified to AEC-Q100 grade 1, which is minus 40 to 125 degrees ambient, and it is built for circuits that stay connected to the battery with the ignition off. The quiescent current of 15 microamp typical, 25 microamp maximum over temperature, is the reason it appears in body modules, door modules and remote keyless entry receivers, where the load is a sleeping microcontroller and the current budget is written in years rather than hours.

Order code and package

TPS7B6950QDBVRQ1Active, SOT-23 (DBV) body, 5 pins, 3000 pieces on a large reel, Sn finish, marking ZAZ2, printed at MSL Level-3-260C-168HR
TPS7B6950QDBVRQ1.AActive, the same string on a second row, printed at MSL Level-2-260C-1YEAR
TPS7B6933QDBVRQ1Active, the 3.3 V member of the same die, marking ZBF2, on the Level-3 row
TPS7B6925QDBVRQ1Active, the 2.5 V member, marking ZBE2, printed at Level-2 with a one year floor life
Temperature rangeminus 40 to 125 degrees ambient, grade 1 qualification

Electrical parameters that decide the application

Input voltage4 V to 40 V operating, 45 V transient
Output5.0 V fixed, 150 mA maximum
Output accuracyplus or minus 3 per cent from 1 mA to 150 mA with the input at 6.5 V or above
Quiescent current15 microamp typical, 25 microamp maximum over the full temperature range
Dropout450 mV typical at 100 mA, 800 mV maximum
Undervoltage detection3.65 V, with the output following the input below that
Current limit500 mA, short circuit protected
Ripple rejection60 dB at 100 Hz with a 2.2 microfarad output capacitor and a 10 mA load

Family variants and how they differ

TPS7B6950-Q15.0 V fixed, the string on this page
TPS7B6933-Q13.3 V fixed, same die and same five pin body
TPS7B6925-Q12.5 V fixed, same family
DBV bodyfive pin SOT-23, 210.4 degrees per watt junction to ambient on a JEDEC board
DCY bodyfour pin SOT-223, 64.2 degrees per watt, for boards that have to drop more volts

Points to check before this part goes on a BOM

Fifteen microamp is the number a battery budget is built on, and it compounds. Fifteen microamp running continuously for a year is 131 milliamp hour, and the maximum over temperature is 25 microamp, which is 219 milliamp hour. Against a 5 amp hour battery that is small. Against a 200 milliamp hour backup cell it is the whole budget, which is why the maximum figure has to be used in the calculation and not the typical one.

The five volt version needs six and a half volts at the input to meet its accuracy row. The regulated output table is specified from 6.5 V to 40 V for the 5 V member, and the supply table shows the part starting to conduct at 5.5 V. Between those two numbers the output follows the input minus the dropout and is outside the plus or minus 3 per cent window. A board that feeds this part from a 5 V rail and expects 5 V out is relying on a condition the vendor does not specify.

Forty volts continuous and 45 V transient is a 12 V or 24 V bus part. A 24 V rail at plus twenty per cent is 28.8 V, which is inside the range with room. A load dump on a 12 V vehicle rail reaches far above 45 V unless the alternator clamp works, so the transient rating is not a substitute for a clamp. The part is automotive qualified, and the qualification covers the temperature and the test regime, not an unlimited supply.

The dropout figure that matters is the maximum, not the typical. Four hundred and fifty millivolt typical at 100 mA sounds comfortable, and 800 mV maximum is the number that decides whether a 5 V output holds at the bottom of a 6 V rail. At 150 mA the figure is worse again. A rail that has to hold 5 V while the input falls to 5.5 V is outside the specified window whatever the typical curve shows.

The five pin body carries about 190 milliwatt at 85 degrees ambient. With 210.4 degrees per watt junction to ambient, a 40 degree rise to a 125 degree junction allows 190 mW. Dropping 12 V to 5 V at 100 mA is 700 mW, which is nearly four times that, so the same part that is rated 150 mA carries only about 27 mA from a 12 V bus into a 5 V load. The 150 mA rating belongs to a 6.5 V input. This is the single most common mistake on a board that uses a high voltage regulator to make a 5 V housekeeping rail.

The four pin SOT-223 body exists for the boards that drop more volts. Its junction to ambient figure is 64.2 degrees per watt against 210.4 for the five pin body, so the same die carries more than three times the dissipation. Where the input is a 24 V bus and the load is above 30 mA, the larger body is not a preference, it is the only version that stays inside the junction limit.

Two rows of the same string carry different moisture sensitivity statements. The published row prints MSL Level-3-260C-168HR and the .A row prints Level-2-260C-1YEAR. Level 3 means 168 hours of floor life out of the bag before a bake; level 2 means a year. For a line that builds in small batches the difference decides whether reels are baked or scrapped, so the offer should say which row ships.

The output capacitor range is wide but the ESR window is not unlimited. An effective capacitance between 2.2 and 100 microfarad with an ESR below 2 ohm keeps the loop stable, which covers ceramic, tantalum and most polymer parts. A very small ceramic below 2.2 microfarad after bias derating can let the loop ring on a load step, and a large capacitor with a high ESR can push the output off its DC value under transient load.

Ripple rejection of 60 dB at 100 Hz is modest for an analogue rail. It is measured with a 2.2 microfarad output capacitor and a 10 mA load, and it falls as the frequency rises. On a 5 V rail that feeds a sensor or a radio, the rejection at the switcher frequency of the converter upstream is well below the 100 Hz figure, so a ferrite and a second capacitor are the usual answer rather than a different regulator.

Fault protection folds back rather than latching. The current limit is 500 mA and thermal shutdown sits at 175 degrees with 25 degrees of hysteresis, so a shorted output heats the die until the thermal circuit cycles it. That keeps the part alive but it also means a short shows as a hot regulator and a pulsing output, not as a dead component. A repair that replaces the regulator without finding the short will fail again.

What to confirm before this part goes on a purchase order

Confirm the output voltage, the body and the reel in one line. Three voltages share the same five pin body and the same footprint, and two of them are printed at a different moisture level. A quote that names only the family cannot be checked against a board or against a material declaration.

State the input bus and the load current so the thermal figure can be checked before the order, not after the first build. A 12 V to 5 V rail at 100 mA needs the larger body or a switching converter ahead of the regulator, and that decision is cheaper to take at quote stage than at rework.

Where this order code fits

It keeps a 5 V rail alive for a body control module, a door module or a remote keyless entry receiver on a 12 V or 24 V bus, with the ignition off and only a sleeping microcontroller on the rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can it make 5 V from a 5 V rail? Not within its specification. The regulated output row starts at a 6.5 V input for the 5 V member, and the dropout is 450 mV typical at 100 mA. A 5 V input produces something below 5 V that follows the input, which may run a microcontroller and will not meet the accuracy statement in a datasheet or a test report.

How much current can it really carry from a 24 V bus? The current is set by heat, not by the 150 mA rating. At 85 degrees ambient the five pin body can shed about 190 mW, which at a 19 V drop is 10 mA. The four pin SOT-223 body carries about 620 mW at the same ambient, which is 32 mA. Above that the part cycles on thermal shutdown.

Does it need an output capacitor? Yes. The part is stable with 2.2 to 100 microfarad of effective capacitance and an ESR below 2 ohm, and the ripple rejection figure assumes a 2.2 microfarad capacitor. Running it with no output capacitor leaves the loop without a defined compensation and the output will ring on a load step.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.