TPS7B6933QDCYRQ1
Product Specifications
TPS7B6933QDCYRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B6933QDCYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B6933QDCYRQ1: automotive 40 V, 150 mA, 15 microamp regulator with a fixed 3.3 V output
TPS7B6933QDCYRQ1 is a high voltage automotive regulator with very low quiescent current and a fixed 3.3 V output in a SOT-23 (DCY) body of 5 pins. It accepts 4 V to 40 V with 45 V transients, draws 15 microamps typical at light load, and holds 3.3 V at 150 mA with 450 mV of dropout at 100 mA, in a 2.9 mm by 1.6 mm body.
Order code and package
| Order code read out | TPS7B6933 Q DCY R Q1: 3.3 V fixed output, automotive qualified, DCY 5 pin SOT-23, R tape and reel |
| Package | SOT-23 (DCY), 5 pins, 2.90 mm by 1.60 mm |
| Second body | SOT-223, 4 pins, 6.50 mm by 3.50 mm, used where the thermal path needs the tab |
| Family outputs | 2.5 V, 3.3 V and 5.0 V fixed, order codes TPS7B6925-Q1, TPS7B6933-Q1 and TPS7B6950-Q1 |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees ambient |
| ESD | HBM level 2, CDM level C4B |
| Output capacitor | 2.2 to 100 microfarad, low ESR ceramic accepted, which avoids the old tantalum rule |
Electrical parameters that decide the application
| Input voltage | 4 V to 40 V continuous, 45 V transient |
| Output voltage | 3.3 V fixed, no divider needed |
| Output current | 150 mA maximum |
| Quiescent current | 15 microamps typical at light load, 25 microamps maximum over the full temperature range |
| Dropout | 450 mV typical at 100 mA |
| Protection | thermal shutdown, short circuit and overcurrent limit, all internal |
| Enable | not provided on this body, the part is live as soon as the input is present |
| Accuracy | fixed output tolerance stated in the electrical table over temperature |
Family variants and how they differ
| TPS7B6933-Q1 | 3.3 V fixed, the part on this page |
| TPS7B6925-Q1 and TPS7B6950-Q1 | 2.5 V and 5.0 V members of the same family, same silicon, different trim |
| SOT-23 and SOT-223 | the small body for control modules, the tabbed body where dissipation is higher |
| Always on use | the low quiescent current is the reason the family exists, so the parts are aimed at standby rails |
| No enable pin | the family has no shutdown input, which removes a leakage path but also a control option |
| Transient behaviour | a 45 V transient rating is the defined automotive event, not an unlimited input clamp |
Points to check before this part goes on a BOM
The 15 microamp figure is typical and light load. At 150 mA the part draws far more, and the guaranteed maximum over temperature is 25 microamps, not 15. A standby budget of 20 microamps is therefore outside the guaranteed limit even though the typical number makes it look comfortable.
450 mV of dropout is quoted at 100 mA, not at the 150 mA rating. At full load the dropout is higher, so a 3.3 V output needs about 3.8 V at the input to stay in regulation at 150 mA. A cranking profile that drops to 3.5 V will not hold the rail, and that is exactly the condition automotive modules are tested against.
There is no enable pin. The regulator starts as soon as the input crosses its threshold and cannot be shut down by the microcontroller. For an always on standby rail that is a feature, because there is no shutdown leakage path and no control line to fail. For a rail that has to be sequenced behind another supply it is a limitation, and the sequencing has to happen on the load side.
The input range covers a load dump only through the 45 V transient rating. A 40 V continuous input is the steady state limit, and automotive load dump can reach far above that. The part survives the transient the standard defines, not every transient a bench supply can produce, so a front end clamp still belongs in the circuit.
Two bodies, one die, different thermal reality. The SOT-23 has no tab and relies on the pins and the board, while the SOT-223 tab spreads heat into copper. At 24 V in and 3.3 V out the part dissipates 3.1 W at 150 mA, which only the larger body survives, so the body choice is a thermal decision before it is a footprint decision.
The part has no reverse battery protection of its own. A battery connected backwards will forward bias the body diode and the internal structures, and the regulator is not the device that survives it. A series diode or an ideal diode controller belongs ahead of it in any circuit where a technician can connect the battery the wrong way round.
The input capacitor is the other half of the transient story. A 10 microfarad ceramic close to the input pin holds the rail through the fast edges of a load dump, and a capacitor on the far side of a connector does not. The 45 V rating is only useful if the pin actually sees a clamped waveform.
Quiescent current is what sells this part, and it is also what a board can lose. A divider on the output for a monitor, a pull up on the enable-less output or a leakage path through a Schmitt trigger input can each draw more than the regulator itself. A standby budget has to be measured at the battery terminal, not at the regulator pin, and it has to be taken at the highest temperature the module will see, because the quiescent current is specified over the full range and not at 25 degrees alone.
The SOT-223 body is the one to choose above a few volts of differential. Its tab is a real heat path, while the SOT-23 relies on the pins and the copper around them. At 12 V in and 3.3 V out the part dissipates 1.3 W at 150 mA, which is at the edge for the small body and comfortable for the tabbed one. The tab is also the only place where a probe can measure the die temperature indirectly, which helps when a module is qualified in an oven.
Where this order code fits
These parts hold a 3.3 V standby rail alive in body control modules, door modules, keyless entry receivers, immobilisers and infotainment head units, where the battery rail swings and the module has to keep drawing microamps while the vehicle is parked. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Can it run straight from a 12 V battery rail? Yes, 40 V continuous covers the battery rail with margin, and the 45 V transient rating covers the defined load dump event. A clamp is still recommended ahead of it.
Is there a 5 V version? Yes, TPS7B6950-Q1 in the same family, and TPS7B6925-Q1 for 2.5 V. All three are the same die with different trim.
Why does the part get hot at 24 V in? Because a linear regulator turns the difference into heat. 20.7 V across the pass element at 150 mA is 3.1 W, which is a package and copper question rather than an electrical one.
Does it survive a reverse connected battery? Not by itself. Add series protection ahead of the input, because the internal structures are not rated for a reversed rail.
How low can the input go before the output drops? As a linear regulator it follows the input once the input falls below the output plus the dropout, which at 150 mA is above the 450 mV figure quoted at 100 mA.
Is the 5 V version the same footprint? The family shares the package options, but the output voltage is fixed in each part. A 5 V rail needs TPS7B6950-Q1, not a resistor change on the 3.3 V part.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.