TPS7B6933QDBVRQ1
Product Specifications
TPS7B6933QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B6933QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B6933QDBVRQ1: automotive 3.3 V LDO, 150 mA, 40 V input, 15 microamp quiescent
TPS7B6933QDBVRQ1 is an automotive grade fixed 3.3 V regulator rated 150 mA with a 40 V input window in a SOT-23 body of 5 pins. It is qualified to AEC-Q100 grade 1, which is minus 40 to 125 degrees ambient, and it holds a 3.3 V rail from a battery that swings from 4 V to 40 V with 45 V transients. That is the always-on case in a vehicle: the module is asleep, the battery is somewhere between 9 V and 16 V, and the regulator still has to keep a microcontroller and its memory alive.
Order code and package
| TPS7B6933QDBVRQ1 | Active, SOT-23-5, 3000 pieces on a large reel, SN finish, MSL-3-260C-168 HR |
| Marking | ZBF2 on the DBV body for the 3.3 V option |
| TPS7B6925QDBVRQ1 | Active, 2.5 V in the same body, 3000 pieces on a large reel, MSL-2 |
| TPS7B6925QDCYRQ1 | Active, 2.5 V in the four pin SOT-223, 2500 pieces on a large reel |
| TPS7B6950-Q1 | the 5 V member of the same family |
Electrical parameters that decide the application
| Input voltage | 4 V to 40 V, with 45 V transients |
| Output | 3.3 V fixed, 150 mA maximum |
| Quiescent current | 15 microamp typical, 25 microamp maximum over the full temperature range |
| Dropout | 450 mV typical at 100 mA |
| Accuracy | specified for the automotive grade over minus 40 to 125 degrees |
| Output capacitor | 2.2 to 100 microfarad, low ESR ceramic |
| Protection | short circuit, overcurrent, thermal shutdown |
| ESD | 2 kV human body model, 750 V charged device model |
Family variants and how they differ
| DBV body | five pin SOT-23, this order code, 3000 pieces on a large reel |
| DCY body | four pin SOT-223, larger copper area, 2500 pieces on a large reel |
| Grade | AEC-Q100 grade 1, minus 40 to 125 degrees ambient |
| Fixed options | 2.5 V, 3.3 V and 5.0 V, no adjustable member |
| Pin count | the four pin body omits the enable or the sense pin present on the five pin part |
Points to check before this part goes on a BOM
25 microamp maximum is the number to quote, not 15. The 15 microamp figure is typical at light load and room temperature. The maximum over the full temperature range is 25 microamp, and an always-on module in a vehicle has to be budgeted at the maximum, because the specification is written at 125 degrees where the leakage of every junction is higher.
450 mV at 100 mA against a 150 mA rating is a deliberate mismatch. The dropout figure is quoted at 100 mA, so at the full 150 mA the drop is larger. A 3.3 V rail fed from a battery that has fallen to 3.6 V will not hold regulation at full load. In the always-on case the load is a few milliamp, so the part holds down to about 3.4 V, which is the case that matters.
40 V input with a 45 V transient covers the load dump case only with help. A full load dump on a 12 V system can reach far above 45 V, and the suppressor in front of the regulator is what brings it inside the rating. The part is specified for the clamped event, not for an unclamped one, so the input network is part of the qualification.
MSL-3 with 168 hours of floor life is the handling constraint. The DBV row with the SN finish is a level 3 part, which means 168 hours of exposure before a bake. The 2.5 V DBV row in the same family is printed at level 2. Two parts that look identical on the reel differ in how long they can sit open on a line, which matters to a assembly house planning a week of production.
Four pins against five is a real difference. The SOT-223 body has four pins and the SOT-23 body has five. The extra pin carries the enable or the sense function, so a substitution between the two bodies is not a drop in even though the voltage and the current match. The land pattern differs as well.
A 2.2 microfarad minimum output capacitor is not a suggestion. The regulator is stable with low ESR ceramic capacitors from 2.2 to 100 microfarad. Below 2.2 microfarad the loop is outside its specified range and the transient response is not guaranteed. On a board where a 1 microfarad capacitor was inherited from another regulator, this part will not behave.
Grade 1 means the ambient range, not the junction range. The junction runs above ambient by the dissipation times the thermal resistance. At 150 mA and a 12 V input the part dissipates 1.3 W, which in a SOT-23-5 is well beyond what the package can pass at 125 degrees ambient. The always-on load is small for a reason, and a board that pulls 150 mA continuously from 12 V belongs in a switching converter.
The family has no adjustable member. The options are 2.5 V, 3.3 V and 5.0 V, all fixed. A rail that needs 3.0 V or 3.6 V cannot be made from this family with a divider. That is worth knowing before a customer asks for a variant, because the answer is a different part rather than a different resistor.
The four pin body has no enable. Where a module has to switch its own regulator off to save current, the five pin body is required and the enable pin becomes part of the sleep budget. Choosing the SOT-223 body for its thermal performance and then finding the enable missing is a board respin rather than a procurement fix.
A 45 V transient rating covers a clamped event only. An unclamped load dump on a 12 V system can go far above that, and the suppressor in front of the regulator is what brings the event inside the window. A customer asking for a regulator that survives load dump without a suppressor is asking for a part this family does not make.
Where an always-on automotive regulator earns its place
Modules that must keep a microcontroller and its non volatile memory alive while the vehicle is parked for weeks, where the sleep current of the whole module is measured in microamp.
Loads that see the full battery range including a cold crank down to 4 V and a clamped load dump, which is what the 4 V to 40 V window with 45 V transients describes.
Where this order code fits
It keeps an automotive module alive from the battery in sleep mode: infotainment, door modules, keyless entry receivers and immobilisers. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is this part AEC-Q100 qualified? Yes, grade 1, minus 40 to 125 degrees ambient, with the human body model and charged device model classifications stated in the document. The qualification paper is a separate document that a customer usually asks for alongside the part.
Can it supply 150 mA from a 12 V battery continuously? Electrically yes, thermally no in the small body. At 150 mA and 12 V in the dissipation is about 1.3 W, which the SOT-23-5 cannot pass at high ambient. The full current is realistic from a 5 V rail or at low duty cycle.
What is the difference between the DBV and DCY order codes? The body: five pin SOT-23 against four pin SOT-223, with different reel sizes and different moisture levels. The voltage options overlap but the pin count and the thermal capability do not, so they are not interchangeable on a board.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.