TPS7B6925QDCYRQ1
Product Specifications
TPS7B6925QDCYRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B6925QDCYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B6925QDCYRQ1: 2.5 V at 150 mA from a 40 V battery rail
The TPS7B6925QDCYRQ1 is the 2.5 V member of the TPS7B69xx-Q1 line, a 150 mA regulator that accepts 4 V to 40 V at the input and draws 15 uA typical at light load. The DCY suffix is the four pin SOT-223 body, which is the one to order when the board has a tab to solder rather than a 3 mm square pad. Output accuracy is plus or minus 3 percent over the load range, and the current limit sits at 500 mA, so a short on the rail is a current event rather than a fire.
The 2.5 V point exists for a specific reason. Many automotive sensors, CAN transceiver reference pins and standby logic blocks run at 2.5 V, and a rail derived from the 5 V or 3.3 V domain would sit behind a second converter. Deriving it directly from the battery removes that stage, and the 15 uA quiescent current means the rail can stay alive while the module is parked. Dropout is 220 mV typical and 400 mV maximum at 150 mA for the 2.5 V option, so the part follows the battery down during a cold crank without dropping the rail first.
Key electrical data for the 2.5 V part
| Input range | 4 V to 40 V, with 45 V transients and operation down to 4 V during crank |
| Output | 2.5 V fixed at plus or minus 3 percent over 1 mA to 150 mA |
| Quiescent current | 15 uA typical at light load, with a thermal shutdown at 175 C |
| Dropout | 220 mV typical and 400 mV maximum at 150 mA |
| Current limit | 500 mA typical, foldback into a short circuit |
| Rejection | 60 dB across the audio band with a 0.5 V peak to peak input ripple |
| Output capacitor | 2.2 uF to 100 uF effective, with a stable ESR window across the temperature range |
Package, marking and reel data
| Body | SOT-223 DCY, 4 pins, 6.50 mm by 3.50 mm, tab soldered to the board |
| Reel | 2500 pieces, large tape and reel |
| Finish and moisture | SN, level 2, 260 C peak reflow, one year floor life |
| Marking | 7B6925 |
| Alternative body | the DBV five pin SOT-23 ships 3000 per reel for boards with less copper |
Where a 2.5 V rail from the battery is used
Seat modules, steering column switches, ultrasonic park sensors and small actuator drivers all carry a microcontroller that needs a low rail and a sleep current in the microamp range. A 2.5 V rail at 150 mA covers the controller and its sensor front end, and the 40 V input means the same part can hang directly on the battery without a pre regulator. The thermal side is modest: at 150 mA from 13.5 V into 2.5 V the part burns 1.65 W, which the SOT-223 tab has to carry into copper.
The three voltage options in the family, 2.5 V, 3.3 V and 5 V, share a body and a pin out, so one board can be built for several markets with a single change on the bill of materials. That is more valuable than it sounds in automotive, where the same module is often sold in a 3.3 V variant and a 5 V variant and the two should not need two qualifications. The SOT-223 tab is what makes that possible at 150 mA: a 1.65 W load step at 13.5 V in is a copper question, and copper does not change with the voltage option.
Buyer questions on the TPS7B6925QDCYRQ1
Why does the same family have both a SOT-223 and a SOT-23 body? The SOT-223 tab carries heat into the board, the SOT-23 does not. The die is the same, so the choice is made by the dissipation of the rail, not by the electrical specification.
Is the output stable with a small ceramic capacitor? The data sheet gives an effective range of 2.2 uF to 100 uF with a defined ESR window, so a 2.2 uF ceramic is acceptable and a 100 uF electrolytic is acceptable. A capacitor outside that window can make the loop ring.
What is the accuracy over temperature? Plus or minus 3 percent over the full load range, which is the figure to use for a sensor supply. The 2.5 V set point at 25 C is tighter than that, but the guaranteed window is what the system has to live with.
Buying this regulator through a component supplier
Three voltages in two bodies makes six order codes from one die, and a purchase order that names only the voltage will get the wrong body half the time. Our power management cross reference lists the codes by body. For a line that is switching between the two bodies, how to verify a drop in replacement covers the thermal check that the tab change forces.