Contact Us

TPS7A9601DSCR

Brand: Texas Instruments
Texas Instruments TPS7A9601DSCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A9601DSCR — Power Management & Signal Chain | Superb Automation

TPS7A9601DSCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A9601DSCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A9601DSCR: 2 A at half a microvolt of noise

The TPS7A9601DSCR is the 2 A member of the TPS7A9x line, and it carries the same noise claim as the 1 A part in a package that can pass twice the current. The output noise is 0.5 uV RMS over 10 Hz to 100 kHz, rejection is 104 dB at 1 kHz and 48 dB at 1 MHz, and dropout is 160 mV at the full 2 A. The output is set by an external divider from 0.4 V to 5.5 V, and the input accepts 1.9 V to 5.7 V.

Two features make the part more than a quiet regulator. The current limit is programmable, and devices can be paralleled so that two of them share the load, which brings the noise down and the current up at the same time. The power-good threshold is programmable too, so a supervisor can flag a rail at a chosen percentage rather than at a fixed 90 percent. Precision enable with its own UVLO threshold and an adjustable soft start complete the control set, all in a 3 mm square WSON body.

Key electrical data for the 2 A part

Input range1.9 V to 5.7 V, with 500 mV of headroom at 1.75 A for the quoted rejection
Output range0.4 V to 5.5 V adjustable, so a low core rail and a 5 V analog rail share one code
Output current2 A per device, with a current limit that is set by an external component
Dropout160 mV typical at 2 A, 200 mV in the guaranteed table
Noise0.5 uV RMS from 10 Hz to 100 kHz, measured at the same condition as the 1 A member
Rejection94 dB at 100 Hz, 104 dB at 1 kHz, 76 dB at 10 kHz, 58 dB at 100 kHz, 48 dB at 1 MHz
Accuracy1 percent over line, load and temperature, from a trimmed internal reference

Package, marking and reel data

BodyWSON DSC, 10 pins, 3.00 mm by 3.00 mm, thermal pad
Reel3000 pieces, large tape and reel on a 330 mm carrier
Finish and moistureNIPDAU, level 1, 260 C peak reflow, unlimited floor life
Marking7A9601
Familythe 1 A TPS7A94 shares the body and the pin out, so one land pattern covers both

Where 2 A of clean supply goes

Radar receivers, high speed data converter front ends, phased array beam forming boards and instrument front ends all combine a wideband analog section with a digital load that switches hard. A 2 A regulator with 104 dB of rejection at 1 kHz can sit between a switching supply and that analog section, and the 48 dB that survives at 1 MHz is what keeps a clock harmonic out of the receiver band. The 0.4 V floor of the output range covers the low core voltages that newer converters use.

At 2 A and 160 mV of dropout the part burns 320 mW, which a 3 mm body with a pad passes without strain, and that is the point of the low dropout: the headroom is small enough that a linear stage after a buck costs little. Where 2 A is not enough, two devices in parallel give 4 A and 3 dB less noise, with the current limit of each set to half the total so the pair shares evenly. The same 3 mm land pattern takes the 1 A member, so a board can start at 1 A and move to 2 A without a copper change, which matters when a platform is reused across two generations of a converter.

Buyer questions on the TPS7A9601DSCR

What sets the current limit? An external component on the limit pin, so the same order code covers a 1 A rail and a 2 A rail. That is also what allows two devices to share a load without a ballast resistor.

Can the output be taken below 0.5 V? Yes, the range starts at 0.4 V and the divider sets the point. The reference is level shifted so the feedback node can be driven low without losing regulation.

Does the part need a minimum load? No. It regulates from no load to 2 A, and the noise and rejection figures are quoted at currents well below the maximum, which is where an analog rail actually runs.

Buying this regulator through a component supplier

An ultra low noise regulator that feeds a converter or a radar front end cannot be swapped for a generic part without re-measuring the noise floor, so the practical sourcing work is availability and authenticity. Our defense grade components page covers the traceability that radar and instrument programs ask for. For the pin out of the 1 A and 2 A members, power management cross reference has both rows.