Contact Us

TPS7A9201DSKR

Brand: Texas Instruments
Texas Instruments TPS7A9201DSKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A9201DSKR — Power Management & Signal Chain | Superb Automation

TPS7A9201DSKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A9201DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A9201DSKR: 2 A low noise regulator with 40 dB rejection at 1 MHz in a 2.5 mm square body

TPS7A9201DSKR is a 2 A low dropout regulator in a 10 pin WSON that keeps 4.6 uVrms of noise and 40 dB of rejection up to 1 MHz, aimed at the rails that feed data converters and clock circuits in a WSON body of 10 pins. The TPS7A92 regulates from 1.4 V to 6.5 V and delivers 2 A at an output set by an external divider between 0.8 V and 5.2 V, with one percent accuracy over line, load and temperature. Rejection is 60 dB at dc, 40 dB at 100 kHz and still 40 dB at 1 MHz. Dropout is 180 mV typical at 2 A, the current limit window is 2.3 A to 2.9 A, and the body is the 2.5 mm by 2.5 mm DSK package with a thermal pad on the underside.

Order code and package

Order codeTPS7A9201DSKR
Input voltage1.4 V to 6.5 V
Output, adjustable0.8 V to 5.2 V
Rated output current2 A
Reference voltage0.8 V
Accuracyplus or minus 1.0 percent, 5 mA to 2 A
Package10 pin WSON, 2.5 mm by 2.5 mm, DSK body
Pin count10
DocumentSBVS318C, July 2017, revised September 2026

Electrical parameters that decide the application

Dropout at 2 A180 mV typical, 400 mV maximum
Output current limit2.3 A minimum, 2.6 A typical, 2.9 A maximum
Rejection at dc60 dB
Rejection at 100 kHz and 1 MHz40 dB at both
Output noise, 10 Hz to 100 kHz4.6 uVrms with 10 nF on NR/SS and 10 nF feed forward
Noise spectral density at 10 kHz15 nV per root hertz
Line regulation0.003 percent per volt
Load regulation0.03 percent per amp
Input UVLO1.31 V to 1.39 V rising, 290 mV hysteresis
Output capacitor22 uF fitted, 11 uF effective minimum for stability
Thermal resistance62.5 C per W junction to ambient, 7.8 C per W junction to case bottom
Junction range-40 C to 125 C

Points to check before this part goes on a BOM

The rejection curve is the reason to buy this part rather than a generic regulator. Forty decibels at 1 MHz means a one volt ripple riding on the input arrives at the output as ten millivolts, and the same rejection holds at 100 kHz where many low dropout parts have already lost 20 dB. A switching stage at 500 kHz therefore puts its fundamental and its second harmonic in a band the regulator still handles, which is what allows a two stage rail without a second filter.

The noise figure depends on two external parts. The 4.6 uVrms headline is quoted with 10 nF on NR/SS and a 10 nF feed forward capacitor, and the datasheet's own curves show the total moving between roughly 4.7 uV and 6.6 uV as the noise reduction capacitor changes from 10 nF to 10 uF. Fitting the pins and leaving the capacitors off hands back a number closer to the raw regulator noise, so the bill of materials has to carry them.

Two amps with a 400 mV maximum dropout leaves very little room between the input and the output. A 1.2 V rail fed from 1.8 V has 600 mV of headroom at nominal, which is inside the specification, but a supply at minus five percent and a load transient that pulls the input down another 100 mV brings the part to the edge. Where the source is a switching stage, the ripple trough rather than the average is the voltage that has to clear the dropout.

Thermal budget decides where this regulator can be used. At 2 A a 1.5 V drop is 3 W, and 62.5 C per W puts the junction 187 C above ambient, so a 3.3 V to 1.8 V rail at full current is not a still air proposition. At a 300 mV drop the loss is 0.6 W and the rise is 38 C, which is comfortable. The 7.8 C per W junction to case bottom figure is what a thermal pad and a via array can exploit.

Current limit at 2.3 A minimum gives 300 mA of headroom over the rating. That is enough for a resistive load but not for a rail that feeds a bank of decoupling and starts into a precharged node, because the inrush is limited by the soft start ramp and not by the current limit. The soft start current is set by the capacitor on NR/SS, and the datasheet offers a selectable charging current through the SS_CTRL pin so a slow ramp can be chosen without changing the capacitor.

The DSK body is 2.5 mm square with the pad underneath. That makes the board area around it tight: a 22 uF output capacitor and a 10 uF input capacitor have to sit within a couple of millimetres or the effective capacitance at the pins falls below the 11 uF the loop needs. The same constraint applies to the feed forward capacitor, which has to be placed at the regulator rather than at the load, otherwise the rejection improvement it buys arrives too late.

Accuracy is quoted over the full load range rather than at a single point, and the reference is 0.8 V with a divider setting the output. That means the divider tolerance adds to the one percent, so a one percent pair turns the rail into a two percent rail. Boards that need the headline number have to spend on 0.1 percent resistors in the feedback path, and the divider current has to stay well above the 100 nA of feedback leakage so that the leakage does not become a gain error.

Where this order code fits

This order code fits the analogue and clock rails around high speed converters, voltage controlled oscillators, LVDS links and low jitter timing, where the switching stage runs at a few hundred kilohertz and its harmonics fall inside the band the regulator still has to reject. It is also used as a post regulator after a charge pump or a flyback where the input carries a switching ripple that a simple LDO would pass straight through. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What makes this part different from a 2 A general purpose regulator? The rejection holds 40 dB out to 1 MHz and the noise is 4.6 uVrms with the recommended capacitors fitted. Both are aimed at converter and clock rails rather than at housekeeping.

Does it need a minimum load? No, it regulates from 5 mA with the stated accuracy. The stability requirement is on the output capacitor, 22 uF fitted and 11 uF effective.

How much headroom does 2 A need? About 400 mV at the worst case dropout, more if the source has ripple that reaches the trough. The nominal 180 mV figure is a typical value, not a limit.

SUPERB supplies this order code with the DSK tape and reel and states date codes, packing and country of origin on the offer, and the Component Lead Time Solutions page sets out the checks that keep a second source from failing on a converter rail.