TPS7A8500ARGRR
Product Specifications
TPS7A8500ARGRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A8500ARGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A8500ARGRR: 4 A at 0.75 percent accuracy when a bias rail is present
The TPS7A8500ARGRR is the A revision of the 4 A TPS7A85 family, and the difference from the plain part is written in the accuracy column: 0.75 percent maximum over line, load and temperature when the bias rail is supplied, against 1 percent on the earlier die. It sources 4 A with 240 mV of maximum dropout, delivers 4.4 uV RMS of noise at a 0.8 V output and 7.7 uV RMS at the top of its range, and sets its output from 0.8 V to 3.95 V with board straps or up to 5.1 V with an external divider.
That extra 0.1 V of headroom over the plain part looks trivial until a rail has to sit at 5 V for an RF amplifier bias or a legacy 5 V analog block. On the A revision the divider covers 5.1 V, so a 5.0 V set point stays inside the specified range with tolerance to spare. The RGR body is 3.5 mm square with a thermal pad, and the order code ships 3000 pieces on a 330 mm carrier.
Key electrical data for the A revision
| Input range | 1.4 V to 6.5 V without bias, 1.1 V to 6.5 V with bias supplied |
| Output range | 0.8 V to 3.95 V by board straps, 0.8 V to 5.1 V with an external divider |
| Output current | 4 A, with remote sense at the load to remove trace drop |
| Dropout | 150 mV typical and 240 mV maximum at 4 A |
| Accuracy | 0.75 percent maximum over line, load and temperature with the bias rail present |
| Noise | 4.4 uV RMS at a 0.8 V output, 7.7 uV RMS at 5.1 V, over 10 Hz to 100 kHz |
| Rejection and capacitor | 40 dB at 500 kHz, stable with 47 uF or more of ceramic output capacitance |
Package, marking and reel data
| Body | VQFN RGR, 20 pins, 3.50 mm by 3.50 mm, thermal pad underneath |
| Reel | 3000 pieces, large tape and reel on a 330 mm carrier |
| Finish and moisture | NIPDAU, level 1, 260 C peak reflow, unlimited floor life |
| Marking | 8500A |
| Small quantity option | RGRT carries 250 pieces on a 180 mm carrier for the same die |
Where 4 A from a linear regulator is justified
A 4 A linear regulator only makes sense where the alternative is worse. Two cases dominate. The first is a rail that follows a load with a fixed, small headroom, such as a 1.0 V core fed from a 1.3 V buck, where switching noise would land directly on the core supply and where the linear part burns only 1.2 W. The second is a post regulator on an analog rail where the noise floor of the converter is the limit, such as the supply of a high speed ADC or a low jitter clock buffer.
The board has to be built for the current. Four amps through a 3.5 mm package means the pad, the vias and the copper all matter, and remote sense is not a luxury: at 4 A a 10 milliohm trace drops 40 mV, which is more than the whole accuracy budget. The SENSE connection at the load removes that error, and the 47 uF output capacitor absorbs the load step while the loop responds. A four layer board with a solid ground plane under the pad is the cheapest way to keep the loop stable at that current.
Buyer questions on the TPS7A8500ARGRR
Is the A revision a drop in change from the plain part? The body, the pin out and the reel are the same, so the board does not change. The specification does: the accuracy tightens to 0.75 percent with bias, the divider range extends to 5.1 V and the noise at the top of the range is quoted separately.
Does the bias rail have to be present? Only when the input falls below 1.4 V. For a 1.8 V or 2.5 V rail the bias pin is not needed, and the 0.75 percent figure is specified with it in place, so the bias rail is what a 1.0 V core supply should plan for.
How is the output strapped to a value between the standard steps? The ANY-OUT taps add binary weighted offsets to a 0.8 V base, so any value in 50 mV steps can be built from the straps. The data sheet table lists the strap combination for every step.
Buying this regulator through a component supplier
Two revisions of the same family in the same body is a substitution risk on the line, because the plain and the A part look identical in a bin. Our power management cross reference prints the revision next to the body. Where a customer has to decide whether the plain part covers a rail, how to verify a drop in replacement lists the four measurements that separate them.