Contact Us

TPS7A8400ARGRR

Brand: Texas Instruments
Texas Instruments TPS7A8400ARGRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8400ARGRR — Power Management & Signal Chain | Superb Automation

TPS7A8400ARGRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8400ARGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8400ARGRR: 3 A low noise linear regulator with 0.75 percent accuracy when a bias rail is present

TPS7A8400ARGRR is a 3 A low dropout regulator in a 20 pin QFN that reaches 180 mV of dropout and 4.4 uVrms of output noise when its BIAS pin is fed from a rail at least 1.3 V above the output in a VQFN body of 20 pins. The TPS7A8400A is the 0.8 V to 5.15 V member of the TPS7A84A family. Output is set either by an external divider or by the ANY-OUT pins in 50 mV steps up to 3.95 V, and the reference is 0.8 V. Input runs from 1.4 V to 6.5 V on the IN pin, or from 1.1 V when the BIAS pin carries 3.0 V to 6.5 V. Dropout is 180 mV maximum at 3 A with a bias rail, the current limit window is 3.7 A to 4.7 A, and the package is the 20 pin RGR body with an exposed pad.

Order code and package

Order codeTPS7A8400ARGRR
Input voltage, IN without BIAS1.4 V to 6.5 V
Input voltage, IN with BIAS at 3.0 V to 6.5 V1.1 V to 6.5 V
Output, adjustable0.8 V to 5.15 V
Output, ANY-OUT pins0.8 V to 3.95 V in 50 mV steps
Rated output current3 A
Reference voltage0.8 V
Package20 pin VQFN, RGR body, exposed pad
Pin count20
DocumentSBVS291C, April 2017, revised December 2020

Electrical parameters that decide the application

Dropout at 3 A, VIN 1.4 V155 mV typical, 250 mV maximum
Dropout at 3 A, VIN 5.4 V225 mV typical, 340 mV maximum
Dropout at 3 A, VIN 5.6 V270 mV typical, 450 mV maximum
Output current limit3.7 A minimum, 4.2 A typical, 4.7 A maximum
Short circuit current, foldback1.0 A into a 20 milliohm load
Accuracy with BIASplus or minus 0.75 percent, 5 mA to 3 A
Accuracy without BIAS below 2.2 V inplus or minus 1.0 percent
Input UVLO with BIAS1.02 V to 1.085 V rising, 320 mV hysteresis
Input UVLO without BIAS1.31 V to 1.39 V rising, 253 mV hysteresis
BIAS UVLO2.83 V to 2.9 V rising, 290 mV hysteresis
Output capacitor47 uF minimum, 25 uF of effective capacitance
Input capacitor10 uF minimum, 47 uF recommended
Noise reduction capacitor10 nF on NR/SS
Feed forward capacitor10 nF from FB to OUT
Thermal resistance43.4 C per W junction to ambient, 36.8 C per W junction to case top
Thermal shutdown160 C trip, 140 C reset

Points to check before this part goes on a BOM

The BIAS pin is not decoration. Without it the input floor is 1.4 V; with 3.0 V or more on BIAS the IN pin can fall to 1.1 V and the accuracy spec tightens from plus or minus 1.0 percent to plus or minus 0.75 percent. A board that ties BIAS to IN above 3.0 V gets the tighter number for free, while a board running from a 1.2 V rail has to bring a second rail in or accept the wider window.

Three dropout figures are published for the same 3 A load and they rise with input voltage: 250 mV maximum at 1.4 V in, 340 mV at 5.4 V and 450 mV at 5.6 V. The spread is a measurement condition artefact, because each entry is taken with the feedback pin forced 3 percent below its regulation point. For a headroom calculation the low voltage figure is the one that matters, since that is where the regulator runs out of room first.

Dissipation sets the real current limit of this part. At 3 A, a 1.2 V drop is 3.6 W and with 43.4 C per W the junction rises 156 C above ambient before any margin, so a 5 V to 3.8 V rail is close to the practical ceiling in still air. Dropping 5 V to 1.8 V at 3 A would be 9.6 W in a 4 mm body, which no pad on a normal board removes. The 3 A rating belongs to circuits where the input is already close to the output.

The ANY-OUT pins trade resolution for simplicity. Fifty millivolt steps cover 0.8 V to 3.95 V, so every 50 mV multiple is reachable without a divider, but a setpoint such as 1.02 V or 1.15 V outside the grid needs the external pair. When the divider is used the datasheet asks for 12.1 kohm as the upper resistor, chosen to match the internal value for noise and rejection, and 160 kohm as the upper bound on the lower resistor so divider current stays well above the feedback leakage of 100 nA.

Noise of 4.4 uVrms is quoted with a 10 nF capacitor on NR/SS and a 10 nF feed forward capacitor fitted. Against a 16 bit converter on a 5 V span, one LSB is 76 uV, so the regulator contributes about six hundredths of a code. The noise figure therefore only becomes the dominant term when the reference and the converter are quieter than that, which is why the part is aimed at data acquisition rather than at general housekeeping rails.

Current limit is a window rather than a single number, 3.7 A to 4.7 A, and the foldback short circuit current is 1.0 A. A load that pulls 3 A continuously sits only 700 mA below the minimum limit, and a converter style load with a fast transient will trip sooner than a resistive one. In a bench supply application the 1.0 A foldback is the number that decides whether a shorted lead survives, not the 4.2 A typical.

Packing and body matter at the order code level. RGR is the 20 pin QFN with the exposed pad and the trailing R is tape and reel, so the stencil and the thermal via array have to be there before the reel arrives. The pad is the only heat path once the part runs at a watt or more, and the 36.8 C per W junction to case top figure shows that almost everything leaves through the board rather than through the plastic.

Where this order code fits

This order code belongs on the last stage of a low voltage rail in test equipment, medical imaging front ends, radar receive chains and instrumentation, where a switching stage has already dropped the bulk of the voltage and the remaining job is noise and accuracy. It is also the part chosen when an analogue rail has to sit within 200 mV of its source, because the dropout budget is what forces a linear stage rather than a switcher at the point of load. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the output be set without a resistor divider? Yes, up to 3.95 V using the ANY-OUT pins in 50 mV steps. Above that value or below the 0.8 V floor the external divider is the only route.

What happens if BIAS is left open on a 1.2 V rail? The part still regulates, because the IN floor is 1.4 V, but a 1.2 V input is below that floor. BIAS at 3.0 V or more is what allows IN to go down to 1.1 V.

Is the 3 A rating reachable at any input voltage? No. The rating is a current rating; the dissipation at a 3.8 V drop would be 11 W, far beyond what the package removes. Use it where the drop is a few hundred millivolts.

SUPERB supplies this order code against the exact RGR tape and reel string, with date codes, packing and country of origin stated on the offer, and the Component Lead Time Solutions page lists the fields to compare before a linear rail socket is filled from a second line.