Contact Us

TPS7A8018DRBR

Brand: Texas Instruments
Texas Instruments TPS7A8018DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8018DRBR — Power Management & Signal Chain | Superb Automation

TPS7A8018DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8018DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8018DRBR: 1 A at 1.8 V with 63 dB of rejection at 1 kHz

The TPS7A8018DRBR is the 1.8 V fixed output of the TPS7A80 family, a 1 A linear regulator in an eight pin 3 mm by 3 mm VSON body with a thermal pad. Its case rests on rejection rather than on quiescent current: 48 dB at 100 Hz, 63 dB at 1 kHz, 57 dB at 100 kHz and still 38 dB at 1 MHz, measured at 750 mA into a 3.3 V rail. For a board that runs a serializer, a clock buffer or an ADC from a noisy 3.3 V or 5 V bus, that curve is what keeps the supply ripple out of the phase noise and out of the converter's own noise floor.

The output noise is quoted as 14.3 uV multiplied by the output voltage with a 0.01 uF capacitor on the NR pin, which puts the 1.8 V point at about 26 uV RMS over 100 Hz to 100 kHz. Dropout is 170 mV typical at 1 A, so the part needs 2.2 V or more at the input for a clean 1.8 V, and the 4.7 uF ceramic output capacitor is the stability condition written into the data sheet.

Key electrical data for the 1.8 V point

Input range2.2 V to 6.5 V, with the reference requiring 0.5 V of headroom above the output
Output1.8 V fixed, 2 percent from 0 C to 85 C and 3 percent over the full junction range
Output current1 A, current limit 1.4 A typical and 2 A maximum
Dropout170 mV typical at 1 A, 250 mV at 750 mA and 350 mV at 500 mA in the guaranteed table
Quiescent current120 uA typical on the fixed versions, 2 uA in shutdown
Rejection63 dB at 1 kHz and 100 kHz, 57 dB at 100 kHz at 750 mA, 38 dB at 1 MHz
Noise14.3 uV times the output voltage with a 0.01 uF noise reduction capacitor

Package, marking and reel data

BodyVSON DRB, 8 pins, 3.00 mm by 3.00 mm, thermal pad on the underside
Reel3000 pieces, large tape and reel, 8 mm tape on a 330 mm carrier
Finish and moistureSN, level 2, 260 C peak reflow, one year floor life
Marking1G2H
Packing optionthe same die ships as DRBT with 250 pieces on a small reel for prototype builds

Where 1 A at 1.8 V is the right answer

Telecom line cards, PLL and VCO supplies, high speed interfaces and audio front ends are the applications named in the data sheet, and they share a shape: a 1.8 V core or analog rail of a few hundred milliamps, a 3.3 V or 5 V input that already carries switching ripple, and a noise budget that a switching regulator cannot meet without a second stage. A 1 A linear part with 63 dB of rejection at 1 kHz removes that second stage, at the cost of 1.2 W at full load from 3 V in.

The thermal pad is not optional at that current. A 1.5 W dissipation through the 3 mm body without a pad would lift the junction by more than 100 C, which is why the DRB outline puts the pad under the die and why the recommended land pattern ties it to a copper area with vias. With the pad soldered and eight vias into a ground plane the same load runs at about 40 C of rise, and the 1 percent load regulation holds because the feedback is taken at the die rather than at the pin.

Buyer questions on the TPS7A8018DRBR

What does the NR pin do? It is the noise reduction pin. A 0.01 uF capacitor from NR to ground filters the reference and takes the output noise to the figure quoted in the table. Leaving it open raises the noise without affecting stability.

Is the 1.8 V output adjustable? Not on this order code. The adjustable member of the family is TPS7A8001, which sets any output from 0.8 V to 6 V with two resistors and shares the same body and pin count.

How much output capacitance is required? 4.7 uF ceramic is the stability condition, and the transient figures assume it. The capacitor should be a low ESR ceramic placed within a few millimetres of the output pin, because the loop depends on it.

Buying this regulator through a component supplier

A 1 A low noise regulator on a telecom board is usually frozen by the time production starts, so the work is in keeping the approved part available rather than in comparing it. Our power management cross reference keeps the pin compatible rows together by body. When a customer is forced to look at an alternative, how to verify a drop in replacement sets out the checks that matter, from the noise figure to the pad geometry.