Contact Us

TPS7A6150QKVURQ1

Brand: Texas Instruments
Texas Instruments TPS7A6150QKVURQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A6150QKVURQ1 — Power Management & Signal Chain | Superb Automation

TPS7A6150QKVURQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A6150QKVURQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A6150QKVURQ1: 5 V, 300 mA and an enable pin in place of the delay pin

The TPS7A6150QKVURQ1 is the 5 V member of the TPS7A61-Q1 branch, the variant that swaps the RDELAY pin of the TPS7A60-Q1 for an enable input. The regulator itself is the same 300 mA, 40 V part with a 25 uA quiescent current and a 2 percent output window, and the reset output carries a fixed internal power-on delay of about 300 ms when a 100 nF capacitor sits on the pin, or 250 us with nothing connected. What changes is control: a board can now switch the 5 V rail off from a microcontroller, which is what a module wants when it has to keep a 3.3 V domain alive and drop the 5 V analog section.

Cold crank behaviour is identical to the rest of the family. The input runs from 7 V to 40 V, tolerates 45 V transients and holds regulation down to 4 V for up to 130 ms, so a start event does not reset the 5 V domain. Tracking the input keeps the pass element out of dropout during the sag, and the reset output stays asserted until the rail has been in regulation for the programmed delay.

Key electrical data for the 5 V point

Input range7 V to 40 V continuous, 45 V transient, 4 V for 130 ms during crank
Output5.0 V fixed at plus or minus 2 percent, 300 mA maximum
Dropout300 mV at 150 mA, 500 mV at 250 mA, measured at the 5 V output
Quiescent current25 uA typical at light load, below 2 uA with the enable low
Enable thresholds1.2 V low, 2.5 V high, with 150 mV of hysteresis on the input
Rejection60 dB at 100 Hz and 30 dB at 150 kHz with a 0.5 V peak to peak ripple
Resetopen drain, 0.4 V at 5 mA, delay fixed internally, 5.5 us of deglitch

Package, marking and reel data

BodyTO-252 KVU, 5 pins, 6.10 mm by 6.60 mm, exposed tab
Reel2500 pieces, large tape and reel
Finish and moistureSN, level 3, 260 C peak reflow, 168 hour floor life
Marking7A6150Q1
Alternative bodyTO-263 KTT at 500 pieces per reel for boards that want the larger tab

Where a switchable 5 V rail belongs

Automotive head units, centre information displays and hybrid clusters are the three applications the family is written for, and all three share a pattern: a 3.3 V domain that must stay alive for the CAN transceiver and the wake logic, and a 5 V domain for the display, the audio codec or the sensor front end that can be shut down. The enable pin makes that second domain a switch rather than a second regulator, and the reset output tells the processor when the 5 V rail has actually arrived instead of leaving it to a software delay.

At 300 mA from 14 V into 5 V the part dissipates 2.7 W, which is the whole thermal story of a TO-252 in a sealed box. The tab is the only path out, and the 2.5 C per W junction to case figure is measured at the pad rather than in free air. A board that pours 100 mm squared of copper under the tab, with vias into an inner layer, runs about 40 C above ambient at that load, which is inside the 150 C junction limit with margin.

Buyer questions on the TPS7A6150QKVURQ1

Does the enable pin have to be driven by logic? No, it is a high impedance input with a 2.5 V threshold on the high side, so a divider from the battery works as an undervoltage lockout just as well as a microcontroller pin.

Is the reset delay adjustable on this variant? No. The 61 branch has a fixed internal delay, which is the trade for the enable pin. If the board needs a programmable delay, the 60 branch with the RDELAY pin is the one to order.

Can two of these sequence a 3.3 V and a 5 V rail? Yes. Wire the reset output of the first to the enable of the second, and the second rail starts only after the first has been in regulation for its delay. The open drain output tolerates 40 V, so the pull up can sit on the battery rail.

Buying this regulator through a component supplier

The 60 and 61 branches share a body and differ by one pin function, which is exactly the kind of pair that gets mixed on a purchase order, so the order code has to be read in full. Our power management cross reference lists the pair by body and pin function. When a customer needs a second source covered before a build, pin to pin cross reference is where the comparison starts.