Contact Us

TPS7A6033QKVURQ1

Brand: Texas Instruments
Texas Instruments TPS7A6033QKVURQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A6033QKVURQ1 — Power Management & Signal Chain | Superb Automation

TPS7A6033QKVURQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A6033QKVURQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A6033QKVURQ1: a 3.3 V automotive regulator with a reset delay pin

The TPS7A6033QKVURQ1 is a 300 mA, 40 V automotive regulator with a fixed 3.3 V output in the five pin TO-252 body. Its distinguishing feature is the pair of pins that most 40 V parts do not carry: an open drain reset output and an RDELAY pin that sets how long that reset stays asserted after the rail is in regulation. With a 100 pF capacitor on RDELAY the delay is about 300 us, with 100 nF it is about 300 ms, and with the pin left open the internal 250 us default applies. A microcontroller therefore starts from a defined state without an external supervisor.

The input window is 7 V to 40 V, with 45 V transients tolerated and operation down to 4 V for up to 130 ms. That last number is the cold crank case: during a start event the battery can sag to 4 V, and the regulator keeps the rail up for the duration instead of dropping the microcontroller into a brown out. Quiescent current is 25 uA at light load and under 2 uA with the enable low, which matters on a module that sits parked for weeks.

Key electrical data for the 3.3 V point

Input range7 V to 40 V continuous, 45 V transient, 4 V for up to 130 ms during crank
Output3.3 V fixed at plus or minus 2 percent, 300 mA maximum
Dropout300 mV at 150 mA, 500 mV at 250 mA, measured at the 3.3 V output
Quiescent current25 uA typical at light load, below 2 uA with the enable pin low
Reset delay250 us default with RDELAY open, 300 us at 100 pF, 300 ms at 100 nF
Rejection60 dB at 100 Hz and 30 dB at 150 kHz with a 0.5 V peak to peak ripple
Protectioncurrent limit at 1000 mA, thermal shutdown at 165 C with 10 C of hysteresis

Package, marking and reel data

BodyTO-252 KVU, 5 pins, 6.10 mm by 6.60 mm, tab soldered to the board
Reel2500 pieces, large tape and reel
Finish and moistureSN, level 3, 260 C peak reflow, 168 hour floor life
Marking7A6033Q1
Alternative bodythe same die is available in the TO-263 KTT body at 500 pieces per reel

Where the reset delay carries the board

Instrument clusters, body control modules, head units and telematics boxes all run a microcontroller from the battery rail and all need the same three things: a rail that survives load dump, a reset that holds until the clock is stable, and a quiescent drain low enough for a parked car. The TPS7A60-Q1 family answers all three in one part, and the RDELAY pin lets each board choose its own delay without a supervisor IC or a software timer.

The device also tracks the input during a crank. When the input falls toward the output the pass element follows it down rather than dropping out, so the rail stays a fixed drop below the battery instead of collapsing and restarting the processor. That behaviour is why the family is often chosen over a switching regulator for loads under 300 mA: no inductor, no switching noise on the analog rail, and a predictable behaviour during the one event that decides whether a module passes its cold crank test.

Buyer questions on the TPS7A6033QKVURQ1

What is the difference between the TPS7A60-Q1 and the TPS7A61-Q1? The 60 has the RDELAY pin and no enable, the 61 has an enable pin and a fixed internal reset delay. Both are 300 mA, 40 V parts in the same bodies, so the choice is made by whether the board needs to switch the rail off.

Can the reset output drive a microcontroller directly? It is an open drain output that pulls to 0.4 V at 5 mA and leaks 1 uA when released, so it needs a pull up resistor to the rail it supervises. The delay is set by the capacitor on RDELAY and is independent of the load current.

How much copper does the TO-252 body need? Junction to ambient is 26.9 C per W and junction to case 2.5 C per W, so at 300 mA from 14 V into 3.3 V the 3.2 W of dissipation has to leave through the tab. A tab soldered to a copper island is the difference between a working board and a thermal shutdown.

Buying this regulator through a component supplier

Automotive regulators are ordered against a part number that includes the body, and a TO-252 row is not interchangeable with the TO-263 row from the same family when the board has one footprint. Our power management cross reference lists both bodies with their reel sizes. For a line that is already running, date code management keeps the incoming lots inside the window the automotive customer audited.