Contact Us

TPS7A2633DRVR

Brand: Texas Instruments
Texas Instruments TPS7A2633DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2633DRVR — Power Management & Signal Chain | Superb Automation

TPS7A2633DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2633DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2633DRVR: 500 mA, 18 V low quiescent LDO, 3.3 V fixed, power good, WSON-6

TPS7A2633DRVR is a fixed 3.3 V linear regulator rated 500 mA with a quiescent current of 2 microamp and an open drain power good output in a WSON body of 6 pins. The input range runs from 2.4 V to 18 V, so the part sits directly on a 12 V or 15 V industrial bus without a pre regulator, and it still works from a 3.3 V rail that is only just above the output. The power good output is the reason many boards pick this member of the family over a plain three terminal regulator: it lets a microcontroller hold off until the rail is really up.

Order code and package

TPS7A2633DRVRActive, WSON-6, 3000 pieces on a large reel, NIPDAU finish, MSL-1-260C unlimited floor life, marking 1WRP
TPS7A2633DRVRG4Active, the same body and reel with the Green material declaration
TPS7A26 familyfixed outputs from 1.25 V to 5.5 V in the same six pin WSON, plus an adjustable member from 1.24 V to 17.4 V
Temperature rangeminus 40 to 125 degrees junction on every row of the addendum
Body2 mm by 2 mm WSON with the thermal pad on the underside, six pins

Electrical parameters that decide the application

Input voltage2.4 V to 18 V
Output3.3 V fixed on this string, 500 mA
Dropout590 mV maximum at 500 mA, which is the figure that decides the minimum input
Quiescent current2.0 microamp typical, no load
Output accuracy1 per cent over temperature, not only at 25 degrees
Output capacitorstable with 1 microfarad or larger ceramic
Power goodopen drain, active high when the output is inside regulation
Junction temperatureminus 40 to 125 degrees, thermal shutdown above that

Family variants and how they differ

TPS7A2633fixed 3.3 V, the string on this page
TPS7A2601adjustable from 1.24 V to 17.4 V through an external divider
TPS7A25the lower current sibling for loads under 300 mA
PG pinopen drain, so several rails can be wire ORed into one reset line
Overshoot controlan active pulldown limits the overshoot when the load steps off

Points to check before this part goes on a BOM

The 18 V rating is only half the story. The 590 mV maximum dropout at 500 mA sets the floor on the input, so a 3.3 V output needs at least 3.89 V at the pin under full load. A board that runs this part from a 3.3 V bus and expects 3.3 V out will sit in dropout and follow the input down. The 18 V ceiling is what makes the same part usable on a 12 V or 15 V rail, where the dissipation, not the dropout, is the constraint.

Two microamp is the no load figure. That is the number to put against a battery budget, and it is measured with the output unloaded. It rises with load but stays far below a classic 5 mA regulator, which is why the part appears in metering and building control boards that sleep for hours between readings.

Power good is open drain and needs a pull up. Nothing on the pin pulls high by itself. A 100 k resistor to the rail being monitored, or to a 3.3 V housekeeping rail, is enough. Because it is open drain, several of these regulators can share one reset line, and the line only releases when every rail is in regulation.

One per cent over temperature is tighter than it sounds. Many regulators quote one per cent at 25 degrees and two or three per cent over the range. Here the one per cent includes the temperature drift, which matters when the 3.3 V rail is also the reference for an ADC on a metering board.

Dissipation is the real limit at 12 V in. At 12 V in and 3.3 V out at 500 mA the part drops 4.35 W, which no two millimetre package can carry. The 18 V rating is there for transient survival and for light loads. A 12 V rail that needs 500 mA at 3.3 V needs a switching converter ahead of this part, and the LDO is then a post regulator for noise, not the main converter.

The WSON pad is the thermal path. The six pin body has almost no lead area, so the heat leaves through the pad on the underside. A pad tied to a small copper island with four vias to the ground plane carries a few hundred milliwatt. A pad tied to a trace carries far less, and the part will fold back on thermal shutdown under a load it was supposed to handle.

MSL-1 with unlimited floor life is a purchasing advantage. The addendum prints Level-1-260C-UNLIM for the DRV body, which means no bake clock and no floor life tracking on the assembly line. Parts that have been in a drawer for a year can go straight to the line. A broker offer on an unlabelled bag loses that guarantee.

The adjustable sibling is not a drop in. TPS7A2601 uses the same body but brings the feedback node out, so the pin that carries the fixed tap on this part becomes an input. A board that swaps between the two needs the divider fitted and the net renamed. The fixed string is the one to hold for repair demand, because it needs no external parts to produce 3.3 V.

Ask for the marking when a reel arrives. The addendum prints 1WRP for this string. Because the family shares one package and one pinout, the only visible difference between a 1.8 V and a 3.3 V member is the top marking. A reel that was re labelled in the channel is not detectable from the label alone, and a wrong voltage here is a board that powers up and misbehaves rather than one that fails dead.

What to confirm before this part goes on a purchase order

The ordering string names the fixed voltage, so the quote has to carry the full TPS7A2633DRVR and not the family name. A substitute from the same family at a different voltage will fit the pad and produce the wrong rail.

Ask for the date code and the reel label with the marking, and state the country of origin on the offer. For a repair order of a few hundred pieces the small reel is usually cheaper to handle, but this body is published on a 3000 piece large reel, so a short quantity means a broken reel and that has to be agreed before the order is placed.

Where this order code fits

It holds a 3.3 V rail at 500 mA on a 12 V or 15 V industrial bus, in meters, motor drives and building controllers, and hands the microcontroller a power good signal on the way up. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it run from a 3.3 V rail and still give 3.3 V out? No. The dropout is 590 mV maximum at 500 mA, so the input has to sit at about 3.9 V or higher for the output to stay in regulation. Below that the part behaves as a resistor and the output follows the input down.

Does the power good output need an external resistor? Yes, it is open drain. One pull up between 10 k and 100 k to a rail that is present is enough, and several open drain outputs can share the same line if the logic is wired as a wired AND.

Is the 500 mA rating valid at 125 degrees? The current rating is electrical; the thermal limit comes first in a small body. At 125 degrees junction and a large input to output difference the part cannot carry 500 mA, so the dissipation has to be calculated for the real ambient, not read from the headline.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.