TPS7A2533DRVR
Product Specifications
TPS7A2533DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A2533DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A2533DRVR: 3.3 V fixed, 300 mA, 18 V low noise regulator with power good in a 6 pin WSON body
TPS7A2533DRVR is a fixed 3.3 V low dropout linear regulator that holds a 2 microamp quiescent current and reports its own output health on an open drain power good pin in a WSON body of 6 pins. It runs from 2.4 V to 18 V, supplies 300 mA, holds 1 per cent output accuracy over the full temperature range, and drops only 210 mV typical at the rated current. The quiescent current is 2 uA typical and 4.5 uA maximum at zero load, which is what makes it usable on a rail that has to survive a long standby. The 2 mm by 2 mm DRV body is the only package the document publishes for this part.
Order code and package
| TPS7A2533DRVR | 6 pin WSON (DRV), 2.00 mm by 2.00 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 unlimited, marking 1WSP, minus 40 C to plus 125 C |
| TPS7A2533DRVT | same body and same die, 250 pieces on a small reel, the line that a pilot build orders |
| TPS7A2501DRVR | the adjustable member, 1.24 V to 17.66 V set by an external divider, 3000 pieces on a large reel |
| Fixed options | 1.25 V, 1.8 V, 2.5 V, 3.3 V and 5.0 V all appear in the vendor addendum on the same DRV body |
| Second row per code | the addendum repeats every string with an .A suffix and a G4 suffix, so the packing and the finish have to be read per row rather than assumed from the suffix |
| Pin 2 | an NC on the fixed versions and the feedback input on the adjustable version, which is the one difference that keeps the two bodies from being interchangeable on a land pattern |
Electrical parameters that decide the application
| Input voltage | 2.4 V to 18 V operating, 20 V absolute maximum, with an undervoltage lockout between 1.95 V and 2.35 V and 70 mV of hysteresis |
| Output voltage | 3.3 V fixed, 1 per cent accuracy over the full temperature range, 0.9 per cent typical |
| Output current | 300 mA maximum continuous |
| Quiescent current | 2 uA typical and 4.5 uA maximum at zero load, measured on the input pin |
| Shutdown current | 325 nA typical and 600 nA maximum with the enable pin below 0.4 V |
| Dropout voltage | 210 mV typical at 300 mA, 120 mV at 150 mA and 64 mV at 50 mA, with the maximum column at 340 mV, 180 mV and 105 mV for the same three currents |
| Current limit | 510 mA typical and 720 mA maximum, measured with the output pulled to 90 per cent of its set value |
| Power good thresholds | rising at 93 to 96.5 per cent of the output, falling at 84 to 90 per cent, with 3 per cent of hysteresis and a 0.4 V low level at a 500 uA sink |
| Ripple rejection | 75 dB at 10 Hz, 62 dB at 100 Hz and 52 dB at 1 kHz |
| Output noise | 300 microvolt rms over 10 Hz to 100 kHz with a 1.2 V output |
| Thermal shutdown | 165 C junction with a 145 C reset point |
| Output capacitor | 1 uF is enough for stability, the electrical table is taken with 2.2 uF and 1 uF on the input |
Where this order code sits in the family
| TPS7A26 | the 500 mA sibling on the same 18 V process, the part the document itself names when a load outgrows 300 mA |
| 5.0 V member | TPS7A2550, same silicon and same pinout, quoted for a rail that feeds a 5 V sensor chain instead of a 3.3 V logic rail |
| Adjustable member | TPS7A2501, which uses the same 6 pin body but brings the feedback node out on pin 2 and needs two resistors |
| Power good pin | an open drain output, so it can be pulled to a rail other than the output and used to hold a processor in reset |
| Fixed versus adjustable accuracy | 1 per cent is specified for the fixed versions over temperature, while the adjustable member is quoted against the 1.24 V reference and inherits the divider tolerance |
| Higher current | there is no 1 A member in this document, so a heavier rail moves to a different family rather than to another suffix |
Points to check before this part goes on a BOM
The quiescent current is the reason this part exists, and it comes with three different figures that answer three different questions. The 2 uA typical applies at zero load with the regulator enabled. The 4.5 uA maximum is the guarantee over temperature and process. The shutdown row of 325 nA typical and 600 nA maximum applies with the enable pin pulled below 0.4 V. A standby budget has to use the maximum numbers, and the difference between 4.5 uA and 600 nA decides whether the always on branch of a battery product can be fed from this regulator or has to be switched by a load switch ahead of it.
The power good thresholds are percentages of the output, not fixed voltages, and that catches people out. Rising is specified at 93 to 96.5 per cent of the 3.3 V rail, which is 3.07 V to 3.18 V, and falling at 84 to 90 per cent, which is 2.77 V to 2.97 V. A processor that needs a clean reset release at 3.0 V cannot get it from this pin alone, because the pin may still be low at 3.0 V in the worst case. The pin is best used as a sequencing handshake or as a monitor input to a supervisor, not as a precision threshold.
Dropout is quoted at three currents in the same table, and only the 300 mA row matters for a rail that runs at its rating. At 300 mA the maximum is 340 mV, so a 3.3 V output needs at least 3.64 V at the input across temperature. At 150 mA the maximum falls to 180 mV and at 50 mA to 105 mV. A board that sizes its input headroom from the 64 mV typical at 50 mA will brown out the rail on the first cold board that draws its full load.
The current limit window runs from 510 mA to 720 mA on a 300 mA part. That is a protection window, not a load rating. The upper end is what a short circuit actually draws for the microseconds before the thermal path reacts, and it is the number to use when sizing a series ferrite, a fuse or a trace width on the input side. The lower end is what guarantees the part will still deliver its rated 300 mA on a hot board, and a load that sits close to 300 mA has to be checked against the minimum rather than the typical.
The fixed and adjustable members share a body but not a pinout, and this is the sort of difference that survives a circuit review and fails at the first build. On the fixed version pin 2 is an NC and must be left alone or tied to ground for thermal reasons. On the adjustable version pin 2 is the feedback input, and a board that was laid out for the fixed part and then reordered with the adjustable string has the feedback node shorted to nothing. The order code on the page carries the 33 in it, which is the fixed 3.3 V string.
Stability is specified down to 1 uF of ceramic output capacitance, while the electrical table is taken with 2.2 uF. That is a wider window than most low dropout parts of this generation offer, and it matters on a board that has already been assembled with a 1 uF part in that position. The catch is that the equivalent series resistance window is not published as a band in this document, so the capacitor should come from a series the vendor has characterised rather than from an unknown second source reel found during a shortage.
The thermal path is the exposed pad on the bottom of the WSON body, and the 2 mm by 2 mm outline has very little copper to work with. At 18 V in and 3.3 V out with 300 mA, the part dissipates 4.4 W, which no 2 mm body can carry. Real applications keep the input near 5 V, where the dissipation is half a watt, or they run the load intermittently. Any application that expects full current from an 18 V source has to move to a larger package in the same family rather than add copper to a 2 mm pad.
Where this order code fits
It sits on standby rails in building automation controllers, smart meters, portable power tools and motor drive boards, where a 3.3 V logic rail has to stay alive from a 12 V or 18 V bus while the rest of the board is asleep. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Date Code Management page.
Questions buyers ask
What is the real quiescent current over temperature? 4.5 uA maximum at zero load and 600 nA maximum in shutdown. The 2 uA and 325 nA figures on the front page are typical values at room temperature.
Can the power good pin be used as a reset for a processor? Only as a sequencing handshake. The rising threshold can be as low as 93 per cent of the output, and the falling threshold as low as 84 per cent, so it is not a precision supervisor.
How much headroom does a 3.3 V rail need? 3.64 V at the input for the full 300 mA across temperature, because the maximum dropout is 340 mV at that current. At 150 mA the requirement falls to 3.48 V.
Is the part stable with a 1 uF output capacitor? Yes. Stability is specified from 1 uF, and the electrical table itself is taken with 2.2 uF, so both values are inside the characterised range.
Does the fixed 3.3 V version need external resistors? No. The divider is internal and pin 2 is an NC. The adjustable member, TPS7A2501, is the only one that uses pin 2 as a feedback input.
What happens on a shorted output? Current limit acts between 510 mA and 720 mA, and thermal shutdown at 165 C junction takes over if the fault holds. Both are non latching, so the rail recovers when the short clears.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.