Contact Us

TPS7A2033PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A2033PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2033PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A2033PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2033PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2033PDBVR: 3.3 V fixed 300 mA ultra low noise LDO in SOT-23-5

TPS7A2033PDBVR is a linear regulator with 7 microvolt RMS of output noise, 95 dB of rejection at 1 kHz and 6.5 microamp of quiescent current in a SOT-23 (DBV) body of 5 pins. It takes 1.6 V to 6.0 V in and delivers a fixed 3.3 V at up to 300 mA with 145 mV of dropout, so a 3.6 V or 5 V rail has enough headroom. The device needs no noise bypass capacitor, which is unusual for a part in this noise class and is what keeps the solution to two small ceramic capacitors.

Order code and package

Order code read outTPS7A20 33 P DBV R: regulator TPS7A20, 3.3 V fixed output, P means active discharge fitted, DBV five pin SOT-23, large tape and reel
PackageSOT-23 (DBV), 5 pins, 2.90 mm by 2.80 mm
Carrier in the vendor addendumTPS7A2033PDBVR at 3000 pieces on a large reel, marked QO, active and in production; the DQNR row is the same voltage in the 4 pin X2SON
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishNickel palladium gold with tin, quoted as NIPDAU or SN
Temperature gradeJunction minus 40 to plus 125 degrees
Absolute maximum6.5 V on the input pins, and 3.6 V on the enable and feedback pins where they exist

Electrical parameters that decide the application

Input range1.6 V to 6.0 V, with the output regulating from 0.3 V of headroom above the set point
Output3.3 V fixed, 300 mA, with plus or minus 1.5 percent accuracy over load, line and temperature in the small packages
Accuracy in this packageThe DBV body is specified as plus or minus 30 mV for any output at or above 2.8 V, which at 3.3 V is plus or minus 0.9 percent
Dropout145 mV maximum at 300 mA in the DBV body for outputs between 2.5 V and 5.5 V, so a 3.6 V rail leaves 150 mV of margin
Quiescent current6.5 microamp typical, with a 13 to 40 microamp maximum depending on the grade and temperature
Output noise7 microvolt RMS over 10 Hz to 100 kHz, with no bypass capacitor on the reference
Rejection95 dB at 100 Hz and 1 kHz at 20 mA, 92 dB at 1 kHz and 300 mA, and 40 to 45 dB at 1 MHz
Current limit360 mA minimum, 520 mA typical and 730 mA maximum, with a 160 mA short circuit value
Enable thresholds0.9 V minimum to enable and 0.3 V maximum to disable, so a 1.2 V logic pin can drive it
Discharge150 ohm active discharge from output to ground when the device is disabled, which is what the P in the order code denotes
Thermal shutdown165 degrees junction, with the output released rather than latched
Start upInternal soft start that limits inrush into the output capacitor, with no external component required

How the order code and the family fit together

TPS7A2033PDBVR3.3 V fixed, active discharge, SOT-23 five pin, 3000 piece reel
TPS7A2033PDQNRthe same voltage and discharge behaviour in the 1 mm by 1 mm X2SON body
TPS7A2033DQNRthe X2SON body without the active discharge, which is the version to use where a slow decay is wanted
Other voltages0.8 V to 5.5 V in fixed steps, all with the same 300 mA rating and the same noise figure
TPS7A20 familythe whole group shares the reference and the error amplifier, so noise and rejection curves carry across the voltage options

Points to check before this part goes on a BOM

Seven microvolts RMS without a noise bypass capacitor is the headline, and it holds because the reference is filtered inside the package. Older low noise regulators reached the same figure with a 10 nF to 100 nF capacitor on a dedicated pin, and that capacitor was both a cost and a leakage path at high temperature. A board that replaces such a part with this one has to remove the bypass capacitor rather than leave it floating, because the pin it sat on does not exist.

The rejection figure is measured at 20 mA and at 300 mA, and the difference between 95 dB and 92 dB at 1 kHz is small but the difference at 1 MHz is not: 45 dB at light load against 40 dB at full load. A rail that feeds a switching converter's own harmonics needs the full load figure, and a rail that feeds a low noise amplifier at 10 mA gets the better number. Quoting the light load figure for a 300 mA rail overstates the filtering by about 5 dB at the frequencies where it matters most.

The DBV package has a different accuracy specification from the small bodies, and it is worth reading carefully. In the X2SON and chip scale parts the tolerance is plus or minus 1.5 percent over the whole output range; in the SOT-23 body the specification is plus or minus 30 mV for outputs at or above 2.8 V, which at 3.3 V is tighter than 1.5 percent and at 2.8 V is about 1.1 percent. The difference comes from the package's thermal behaviour rather than from the die.

Dropout of 145 mV at 300 mA is a real constraint on a 3.3 V output. A 3.6 V rail at minus five percent is 3.42 V, which leaves 120 mV, less than the maximum dropout at full load; the regulator will follow the input down and the output will sag rather than regulate. A 5 V rail has no such problem, and a 3.6 V rail should either accept the sag at full load or use a part with lower dropout. This is the calculation that most often decides whether a 3.3 V LDO is viable.

The P suffix means the output is actively discharged through 150 ohm when the device is disabled. That is helpful when a rail has to come down before another rail comes up, and it is unhelpful when a rail is used as a reference that must decay slowly. The same voltage is available without the discharge as TPS7A2033DQNR, so the choice is a purchase order decision rather than a board change, and the two parts share a land pattern only within their own package.

Quiescent current of 6.5 microamp is the number that decides battery life, and it applies at light load. At 300 mA the ground current rises, and the package has to dissipate 0.6 W if the input is 5 V and the output 3.3 V. The SOT-23 body handles that on a reasonable copper area, and the X2SON body needs the thermal pad soldered well. A board that runs the part at full load in a sealed enclosure should check the junction temperature rather than trust the current rating.

Where this order code fits

Used to post regulate a switching rail for noise sensitive loads: RF and microwave front ends, ADC and DAC reference rails, phase locked loops, sensor front ends, audio codecs and medical instrument analogue supplies. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

Does it need a noise bypass capacitor? No. The reference is filtered inside the package and the 7 microvolt figure is specified without one. A 1 microfarad ceramic on the output is the requirement, and adding a large bypass on the output only changes the transient response.

Can it run from a 3.6 V rail at 3.3 V out? Only with care. Dropout is 145 mV maximum at 300 mA, so a 3.6 V rail at minus five percent leaves 120 mV and the output will follow the input down at full load. At 100 mA the margin is comfortable.

What is the difference between the P and non P versions? The P suffix adds a 150 ohm active discharge from output to ground when the device is disabled. Both are available in the same voltages; the choice depends on whether the rail should decay quickly or slowly.

Is the SOT-23 version as accurate as the small package? It is specified differently. The SOT-23 body quotes plus or minus 30 mV for outputs at or above 2.8 V, which at 3.3 V is better than the plus or minus 1.5 percent of the small bodies. Both are within the same order of accuracy.

How is it handled on the line? Level 1, 260 degrees, unlimited floor life, with a nickel palladium gold finish. No baking and no dry pack shelf life, which suits low volume builds that keep reels on the shelf.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.