TPS7A1650DGNR
Product Specifications
TPS7A1650DGNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A1650DGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A1650DGNR: 60 V input, 5 microamp quiescent, 100 mA fixed 5 V regulator
TPS7A1650DGNR is an ultralow quiescent current linear regulator with enable and power-good in a HVSSOP PowerPAD body of 8 pins. It takes 3 V to 60 V at the input, holds a fixed 5 V output at up to 100 mA, draws 5 microamp with no load and 1 microamp in shutdown, and gives up only 60 mV of dropout at 20 mA.
Order code and package
| Ordering string | TPS7A1650DGNR, DGN package, tape and reel |
| Package | 8-pin HVSSOP with PowerPAD, 3.00 mm by 3.00 mm |
| Output option | Fixed 5.0 V; the adjustable member of the family spans 1.2 V to 18.5 V |
| Ambient range | -40 C to 125 C |
| Output capacitor | 2.2 microfarad ceramic, stable without a tantalum |
Electrical parameters that decide the application
| Input range | 3 V to 60 V continuous, and it keeps regulating through input transients |
| Quiescent current | 5 microamp operating, 1 microamp in shutdown |
| Output current | 100 mA |
| Dropout | 60 mV at 20 mA |
| Accuracy | 2 percent over load, line and temperature |
| Power good | Open-drain, active high, with a delay set by an external capacitor |
| Protection | Current limit and thermal shutdown |
Points to check before this part goes on a BOM
Five microamp for a year is 43.8 mAh. A regulator that draws 100 microamp instead needs 876 mAh for the same year, which is more than a AA cell holds. That ratio, not the dropout, is the reason this part exists, and it only pays if the rest of the rail is quieter than the regulator itself.
The 60 V input is there for the fault case rather than the operating point. In a 48 V bus or an automotive 12 V system the steady state is far below 60 V, but a load dump or a coil event is not, and a 40 V part is a shorted pass device waiting to happen. The regulator holds regulation through that event instead of dropping the rail.
Voltage across the pass device is what decides whether 100 mA is available. From 12 V to 5 V at 100 mA the part dissipates 0.7 W, which the HVSSOP pad can pass. From 48 V to 5 V at 100 mA it is 4.3 W, which it cannot, and the honest operating point at 48 V in is closer to 20 mA. A 5 V rail from a 60 V source is a low-current standby supply, not a power rail.
Dropout of 60 mV at 20 mA works out to 3 ohm. Scaling that to the full 100 mA gives roughly 300 mV, so the input has to stay above 5.3 V for a clean 5 V. A 5 V input feeding a 5 V output, which happens when a USB rail is used as the source, sits in dropout and passes the input minus the drop, which is fine for a digital load and not fine for anything that needs 5 V plus or minus 2 percent.
The power-good output with a capacitor-set delay is the sequencing tool. It lets a microcontroller start only after the rail has been valid for a chosen time, without an external supervisor, and it is open drain so the pull-up can sit on the same rail the processor uses. The delay capacitor is the part that gets forgotten in a copy of the circuit, and without it the flag is immediate.
A 2.2 microfarad ceramic output capacitor is enough, which matters on a board where every millimetre counts. The regulator is stable across the ceramic ESR range, so the capacitor can be an X5R in a small case as long as the voltage coefficient is respected: a 6.3 V rated part at 5 V can lose more than half its nominal capacitance, and the loop is specified against the value actually fitted.
The 2 percent accuracy figure is worth reading against what it is 2 percent of. On a 5 V output that is 100 mV, which is wider than the tolerance band of most digital loads and narrower than the tolerance of a load that expects a 5 V plus or minus 5 percent rail. The point of the part is not precision, it is keeping a rail alive from a high-voltage source at microamp standby, and the accuracy is adequate for that job while remaining honest about what it is not.
Where this order code fits
It suits a standby rail in a battery pack, a smoke or gas detector, a power tool pack with many cells, or an automotive body module where the regulator has to survive the transient without draining the battery over a parked month. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Why is the quiescent current quoted at both 5 microamp and 1 microamp? Five microamp is the operating figure with the enable high and no load. The 1 microamp figure is shutdown with the enable low. A battery product that leaves the enable high all the time can only use the first number.
Can this replace a 40 V regulator directly? Electrically yes if the output and the pinout match, but the higher input rating changes the dissipation in the same package, so the load current has to be rechecked against the thermal pad rather than assumed from the old circuit.
Is the fixed 5 V version adjustable? No. The fixed parts have the divider inside. If the board needs a different output the adjustable member of the family is the orderable to buy, and it needs two external resistors whose tolerance adds to the 2 percent.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.