Contact Us

TPS7A1018PDSER

Brand: Texas Instruments
Texas Instruments TPS7A1018PDSER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A1018PDSER — Power Management & Signal Chain | Superb Automation

TPS7A1018PDSER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A1018PDSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A1018PDSER: 1.8 V at 300 mA from a source only 70 mV higher

The TPS7A1018PDSER is the 1.8 V fixed output of the TPS7A10 family in the six pin WSON body coded DSE. It delivers 300 mA with a maximum dropout of 90 mV in this body, and 70 mV in the smaller five bump package, because the internal circuitry runs from a separate bias pin rather than from the main input. The input itself may sit as low as 0.75 V, which is well below the 1.8 V output; the bias pin supplies the gate drive and the reference.

For the system builder the consequence is simple. A buck converter that produces 1.9 V can feed this regulator and the rail stays in regulation down to a 1.89 V source at full load, so the post regulator no longer needs to be a switching stage with its own inductor and its own ripple. The output noise and the rejection figures apply to the IN pin, and the bias pin has its own, much larger, dropout requirement of about 0.85 V at 300 mA.

Key electrical data for the 1.8 V point

Input range0.75 V to 3.3 V on IN, 1.7 V to 5.5 V on BIAS, bias at least 1.4 V above the output
Output current300 mA, current limit around 600 mA, short circuit 150 mA
Quiescent current1.6 uA on the input pin, 6 uA on the bias pin, both at no load
Accuracyplus or minus 1.5 percent over load, line and temperature
Dropout90 mV maximum at 300 mA in the six pin WSON body, 70 mV in the five bump body
Rejection60 dB at 1 kHz on the input pin, with a separate figure for the bias pin
Stability2.2 uF on the input, 2.2 uF on the output and 0.1 uF on the bias pin

Package, marking and reel data

BodyWSON DSE, 6 pins, 1.5 mm by 1.5 mm, exposed thermal pad
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAUAG
Moisturelevel 1, 260 C peak reflow, unlimited floor life
MarkingDU, one letter pair for the trim and the lot

Where a 1.8 V, 300 mA core rail belongs

This is the rail that follows a DC to DC converter in a phone, a tablet, a camera module or a portable medical device. The switching stage is set about 100 mV above the target and this regulator removes the ripple and the load transient, so the processor core and the analog front end see a quiet 1.8 V. Because the input to output difference is only 100 mV, the dissipation at 300 mA is 30 mW, which is why the part can sit in a 1.5 mm square body with no heatsink.

The checks that catch people are the bias sequencing and the output capacitor. The bias pin has to reach 1.4 V above the output before the enable is asserted, otherwise the start up is not monotonic. And the output capacitor has to be at least 2.2 uF of ceramic, not the 1 uF that the nanopower families accept, because the loop is compensated for that value. A board that copies a 1 uF value from another regulator will ring at light load.

Buyer questions on the 1.8 V WSON code

Why does this part need two supply pins? Because a conventional regulator cannot control a pass element whose gate has to sit above a 1.8 V output when the input is only 1.9 V. The bias pin provides the headroom for the internal circuits while the main path carries only load current, which is what allows the 70 mV to 90 mV dropout.

Is the dropout the same on the bias pin? No. The bias dropout is about 0.85 V at 300 mA, roughly ten times the input path figure. It has to be treated as a separate rail requirement in the power budget.

Can it run from a single 1.9 V supply? Not reliably. The bias pin needs 1.4 V more than the output, which a 1.9 V source cannot provide for a 1.8 V output. A second higher rail, usually the battery or the 3.3 V system rail, has to be available.

Sourcing this rail

Two rail regulators with a bias pin are unusual enough that a replacement usually needs a circuit review rather than a part number swap. The power management cross reference page groups the options by pin function, and purchase order follow up covers the confirmation steps on a 3000 piece reel of a part that ships from one fab.

At 1.8 V the part is usually fed from a buck converter set about 100 mV higher, and the whole value of the arrangement rests on the 90 mV dropout in this body being met at full load over temperature. The input and output capacitors are 2.2 uF each and the bias capacitor is 0.1 uF, which is a larger set than the nanopower families need; a board that substitutes 1 uF parts because they were already on the bill of materials will see ringing at light load. The enable threshold is 1.0 V, so 1.8 V logic drives it directly, and the bias pin has to be alive before the enable is asserted or the start up is not monotonic.