Contact Us

TPS7A1015PDSER

Brand: Texas Instruments
Texas Instruments TPS7A1015PDSER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A1015PDSER — Power Management & Signal Chain | Superb Automation

TPS7A1015PDSER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A1015PDSER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A1015PDSER: a 1.5 V rail from a 0.75 V input with a separate bias pin

The TPS7A1015PDSER is the 1.5 V fixed output of the TPS7A10 family, a 300 mA regulator built for a very different problem from the rest of this band. Its input range starts at 0.75 V, which is below the threshold of any ordinary linear regulator, because the internal circuitry is powered from a second pin. The main path from IN to OUT carries only the load current, and the maximum dropout in that path is 70 mV at 300 mA in the five bump body, so a 1.5 V rail can be held from a 1.57 V source.

The second rail, marked BIAS, has to sit at least 1.4 V above the output and within 1.7 V to 5.5 V, and it draws about 6 uA. That bias rail is usually the battery or the system 3.3 V, while the main input is the output of a step down converter that is already close to the load voltage. The arrangement is common in phones, tablets and wearables, where the core rail is 1.5 V or lower and the only higher voltage available is the battery.

Key electrical data for the 1.5 V point

Input range0.75 V to 3.3 V on IN, 1.7 V to 5.5 V on BIAS, bias at least 1.4 V above the output
Output current300 mA, current limit around 600 mA, short circuit 150 mA
Quiescent current1.6 uA on the input pin, 6 uA on the bias pin
Accuracyplus or minus 1.5 percent over load, line and the full temperature range
Dropout70 mV maximum at 300 mA in the five bump body, 90 mV in the six pin WSON body
Rejection60 dB at 1 kHz, with the bias pin rejection specified separately
Shutdownthe bias rail drops to nanoamps and the input pin to a microamp when disabled

Package, marking and reel data

BodyWSON DSE, 6 pins, 1.5 mm by 1.5 mm, with an exposed thermal pad
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAUAG
Moisturelevel 1, 260 C peak reflow, unlimited floor life
MarkingDV

Where a 1.5 V core rail belongs

The part exists for the core voltage of a modern microcontroller or an applications processor, and for the analog supply of a sensor that runs at 1.5 V. In a smart watch or a fitness tracker the 1.5 V domain is fed from a buck converter at 1.6 V, and the last 100 mV is removed by this regulator so the core sees a quiet rail rather than the switching ripple. The 60 dB of rejection at 1 kHz is what makes that work, and the soft start with a monotonic rise keeps the core from seeing a step at power on.

Two conditions catch buyers out. The bias rail has to be above the output by 1.4 V at all times, including during start up, otherwise the regulator does not turn on cleanly. And the bias dropout is 0.85 V to 1.05 V at 300 mA, which is far larger than the 70 mV figure that applies to the main path; a circuit that ties the bias pin to a 2.5 V rail and expects 1.5 V out at full load is asking for a 1.0 V bias dropout to be met by a 1.0 V margin.

Buyer questions on the 1.5 V code

Can the bias pin be tied to the input? Only if the input is at least 1.4 V above the output and stays there. With a 1.5 V output and a 1.6 V input the bias requirement is not met, so the pin has to come from a higher rail.

Why is the dropout so much lower than on other 300 mA parts? Because the pass element is a separate device from the control circuitry. The 70 mV figure applies to IN to OUT only; the bias path has its own dropout of about 0.85 V at full load.

Is the WSON body the same footprint as the DSBGA? No. The 1.5 mm WSON has a thermal pad and a 0.5 mm pitch, while the DSBGA is 0.74 mm by 1.09 mm with 0.35 mm bumps. Boards are built for one or the other.

Sourcing a low input regulator

Low input regulators are a narrow category, and when one goes obsolete the replacement usually needs a new bias arrangement rather than a new part number alone. The obsolete part cross reference hub is the entry point for that work, and material requirements planning covers the lead time on a 3000 piece reel against a build schedule.

The capacitor set is part of the specification rather than a suggestion: 2.2 uF on the input, 2.2 uF on the output and 0.1 uF on the bias pin, all ceramic, and the stability guarantee assumes them. The soft start is built in and monotonic, so the output cannot dip on its way up, which matters when the rail supplies a processor core whose reset is released by a supervisor. The current limit sits at about 600 mA with a 150 mA short circuit figure, so a 300 mA load has roughly twice its rating available for a transient before the limit engages, and the bias pin only carries microamps throughout.