Contact Us

TPS7A0333PDQNR3

Brand: Texas Instruments
Texas Instruments TPS7A0333PDQNR3 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0333PDQNR3 — Power Management & Signal Chain | Superb Automation

TPS7A0333PDQNR3

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0333PDQNR3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0333PDQNR3: a 3.3 V 200 mA nanopower regulator for rails that stay live for years

TPS7A0333PDQNR3 is a fixed 3.3 V low dropout regulator that holds 200 nA of quiescent current even while it is out of regulation in a X2SON (DQN) body of 4 pins. The input window is 1.5 V to 6.0 V, the output is fixed at 3.3 V from a 50 mV table that also covers 0.8 V to 5.0 V, and accuracy is 1.5 per cent over temperature. Dropout is 270 mV maximum at 200 mA, so a 3.6 V rail still holds 3.3 V at full load. A 1 microfarad ceramic capacitor is enough for stability, the enable pin carries an internal pulldown that keeps the part off when the pin floats, and a 1 mA to 50 mA load step settles inside 10 microseconds with about 80 mV of undershoot. The junction range is minus 40 C to 125 C.

Order code and package

TPS7A0333PDQNR3the 3.3 V fixed member on a large reel, printed in the addendum with marking 21TF; the addendum line for this string shows a 12000 piece quantity against a DSBGA label while the tape and reel table lists a 3000 piece reel in the X2SON body, so the body and the packing are confirmed on the offer rather than read from the suffix
TPS7A0333PDQNRthe same 3.3 V die in the X2SON body on a 3000 piece reel with marking Q, which is the string most builds use once the prototype phase is over
TPS7A0333PDBVRthe 3.3 V member in the 5 pin SOT-23 body on a 3000 piece reel, for a board that cannot place a 1 mm square part
TPS7A0333PYCHRthe 3.3 V member in the 4 pin DSBGA body of 0.64 mm by 0.64 mm on a 12000 piece reel, which is the option for a flex or a module where height is the limit
TPS7A0325 and TPS7A0318the 2.5 V and 1.8 V members of the same family, same 200 mA rating and the same bodies, so a board moves between rails without a footprint change
Pin count4 pins in the X2SON body with no enable pin on the smallest option, while the SOT-23 and DSBGA versions carry the enable pin, so the pin function has to be read per body rather than per family

Electrical parameters that decide the application

Input voltage1.5 V to 6.0 V recommended, with the part still regulating below the 1.5 V floor only in the sense that it follows the input down, so a 5 V rail with 10 per cent tolerance is inside the window
Output voltage3.3 V fixed on this code, from a family table of 0.8 V to 5.0 V in 50 mV steps, which is what lets a core rail at 0.9 V or 1.2 V use the same silicon
Output current200 mA, with the current limit above that figure and the thermal pad of the small body setting how much of the current survives at high ambient
Quiescent current200 nA typical, and the figure is held while the part is in dropout, which is the condition where most regulators of this class draw several microamps
Shutdown current3 nA typical with the enable low, which is the number that matters for a shelf life figure on a battery powered meter or a wearable
Dropout voltage270 mV maximum at 200 mA on the 3.3 V output, so the rail needs 3.57 V of input at full load over the whole temperature range
Accuracy1.5 per cent over the full junction range rather than at 25 C only, which is a wider figure than the 0.5 per cent parts used on data converter rails
Transient response1 mA to 50 mA step settles in under 10 microseconds with 80 mV of undershoot, quoted with a 1 microfarad output capacitor
Output capacitor1 microfarad or larger ceramic, with no ESR requirement beyond what a standard X5R or X7R part provides
Enable pinan internal pulldown keeps the regulator off when the pin floats, which removes the external resistor that a battery powered board would otherwise fit
Reverse currentthe pass element blocks current from output to input while the part is disabled, so a rail that stays biased does not feed back into a dead supply
Thermal shutdownthe part shuts down on junction overtemperature and restarts when it cools, which is a protection rather than an operating point on a 200 mA device
Temperatureminus 40 C to 125 C junction over the electrical table, which covers an outdoor meter and an indoor module with the same order code

Bodies and neighbour parts in the TPS7A03 family

TPS7A0333PDQNR3this order code, 3.3 V fixed, in the 4 pin X2SON body, 3000 pieces on a large reel with marking 21TF
TPS7A0333PDBVRthe same die in the 5 pin SOT-23 body, which brings the enable pin out and takes a footprint four times the area
TPS7A0333PYCHRthe 0.64 mm square DSBGA member on a 12000 piece reel, for a flex or a module where height is the limit
Quiescent current200 nA typical while regulating and while in dropout, and 3 nA in shutdown, which is below the self discharge of most cells
Dropout270 mV maximum at 200 mA, so a 3.3 V rail needs 3.57 V of input at full load over temperature
Transienta 1 mA to 50 mA step settles inside 10 microseconds with about 80 mV of undershoot on a 1 microfarad output capacitor
Bodiesthree bodies share the die and only two of them bring the enable pin out, so the footprint decides whether the rail can be switched

Points to check before this part goes on a BOM

Nanopower is only worth paying for if the whole rail is nanopower. A 200 nA regulator feeding a load that leaks 3 microamps in standby buys nothing. The figure that decides the battery life of a water meter or a smoke detector is the sum of the regulator, the microcontroller standby current and the leakage of every capacitor on the rail, and the regulator is usually the smallest of the three.

Dropout at 200 mA is the number that decides a 3.3 V rail from a lithium cell. 270 mV maximum means the cell can fall to 3.57 V before the rail follows it down, which is most of the useful discharge curve. A part with 500 mV of dropout on the same rail starts losing regulation half a volt earlier and needs a larger cell or a boost stage.

The 4 pin body has no enable pin. On the smallest option the regulator is live as soon as the input is above the lockout, so a board that needs to switch the rail off has to use the SOT-23 or DSBGA body. A footprint drawn for one body does not accept the other, and this is the mistake that shows up at the first build rather than at the paper review.

1.5 per cent accuracy is fine for a logic rail and not for a reference. A microcontroller, a sensor front end with its own reference or a radio supply all tolerate 1.5 per cent. A rail that sets an ADC full scale does not, and those boards use the 0.5 per cent members of the family or a shunt reference instead.

The transient figure is quoted for a 1 microfarad output capacitor. Doubling the capacitor reduces the undershoot but also changes the loop, and the data sheet states the stability window rather than an open invitation. A board that adds a 10 microfarad bulk capacitor for a different reason should check the step response on the bench rather than assume it improves.

Reel quantities on this family do not follow the suffix. The same 3.3 V die ships on 3000 and on 12000 piece reels depending on the body, and the addendum lines for the smallest body are not consistent about which carrier belongs to which string. The packing column on the offer is what a purchase order should be written against.

Where a 200 nA regulator changes a product

The obvious case is a battery powered device that spends most of its life asleep: a water meter, a gas detector, a smoke alarm, a wearable that wakes on a button. In those products the sleep current sets the replaceable battery interval, and a regulator that draws 200 nA instead of 2 microamps moves the interval from months to years on the same cell.

The second case is less obvious. A board that is powered from a supercapacitor or a harvested source has a supply that sags slowly, and a regulator that holds its quiescent current in dropout keeps drawing the same tiny current while the rail falls, which lets the microcontroller finish its last write and shut down in order rather than reset in the middle of a flash page.

Reading the body options before fixing a footprint

Three bodies share this die: the 1.0 mm by 1.0 mm X2SON, the 5 pin SOT-23 and the 0.64 mm square DSBGA. They do not share a pad pattern, and only two of the three bring the enable pin out. A build that starts on the SOT-23 for hand assembly and moves to the X2SON for volume needs two footprints on the board from the first revision, or a re-spin at the worst possible moment.

Where this order code fits

a battery powered meter, a smoke or heat detector, a wearable or an always on sensor node where the sleep current of the regulator is a line in the battery budget Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How much current does the regulator itself draw? 200 nA typical while regulating and the same figure while in dropout, and 3 nA with the enable pin low. Those are the numbers to add to the load budget, not the 200 mA rating.

What is the lowest input voltage that still holds 3.3 V? About 3.57 V at 200 mA over temperature, because the maximum dropout is 270 mV. Below that the output follows the input down by the dropout margin.

Is a 1 microfarad output capacitor really enough? Yes for stability, and the transient figures in the document are quoted with that value. A larger capacitor is allowed and lowers the undershoot, but the loop should be checked on the bench rather than assumed to improve.

Can the part be switched off from a microcontroller pin? Only on the bodies that bring the enable pin out. The smallest 4 pin body has no enable, so the choice of body decides whether the rail can be shut down at all.

How does this compare with the TPS709 family? The TPS709 takes up to 30 V of input and delivers 150 mA with 1 microamp of quiescent current, so it suits a 12 V or 24 V line. This part stops at 6 V and is the lower current, lower quiescent choice for a single cell or a 3.3 V rail.

How does SUPERB quote this line? Against the exact ordering string, with the body, the reel quantity, the date code and the country of origin stated on the offer, because the same die ships in three bodies and two reel sizes under strings that differ by three characters.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.