Contact Us

TPS7A0333PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A0333PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0333PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A0333PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0333PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0333PDBVR: 200 mA nanopower LDO, 3.3 V fixed, 200 nA quiescent current, SOT-23-5

TPS7A0333PDBVR is a fixed 3.3 V linear regulator rated 200 mA with a quiescent current of 200 nanoamp and a fast transient response in a SOT-23 body of 5 pins. The part sits between the two extremes of the family: the quiescent current is higher than the 25 nanoamp member and much lower than a conventional regulator, and the transient response is faster than either. It is the version to choose when a radio or a sensor wakes for a few milliseconds and draws tens of milliamp, and the rail still has to survive on a coin cell between events.

Order code and package

TPS7A0333PDBVRActive, SOT-23-5, 3000 pieces on a large reel, NIPDAU finish, MSL-1-260C unlimited floor life, marking 21PF
TPS7A0333DQNRActive, the 1 mm by 1 mm X2SON body, four pins, marking G5
TPS7A02 familythe 25 nanoamp sibling, with a slower transient response and the same bodies
Output options0.8 V to 5.0 V fixed in 50 mV steps across the family
Temperature rangeminus 40 to 125 degrees junction on every published row

Electrical parameters that decide the application

Input voltage1.5 V to 6.0 V
Output3.3 V fixed on this string, 200 mA
Quiescent current200 nanoamp typical, held in dropout
Shutdown current3 nanoamp typical
Dropout270 mV maximum at 200 mA for the 3.3 V option
Transient responsesettling under 10 microsecond, 80 mV undershoot for a 1 mA to 50 mA step
Output accuracy1.5 per cent over temperature
Output capacitorstable with 1 microfarad or larger

Family variants and how they differ

TPS7A03333.3 V fixed in the DBV body, the string on this page
TPS7A02the 25 nanoamp member, for loads that are asleep almost all the time
DQN bodyX2SON-4 at 1 mm square, no enable pin, for the smallest area
Smart enablean internal pulldown holds the regulator off when the enable pin floats
Fixed options0.8 V to 5.0 V in 50 mV steps, so a core rail can be matched exactly

Points to check before this part goes on a BOM

Two hundred nanoamp against twenty five nanoamp is the choice in this family. The lower current part holds its quiescent current down at the cost of a slower loop, which shows as a deeper dip when a load steps. This part draws eight times as much standing current and recovers in under ten microsecond. For a radio that transmits in bursts the second behaviour matters more than the standing current, because a dip below the brownout threshold resets the radio.

The quiescent current is specified in dropout, and that is the hard case. A lithium cell at the end of discharge sits below the regulation point and an ordinary regulator increases its own consumption at that moment. Here the 200 nanoamp holds, which is what allows a product to keep running down to the last of the cell without the regulator itself becoming the load.

Two hundred and seventy millivolt dropout at 200 mA sets the input floor. A 3.3 V output needs 3.57 V at the pin under full load. From a 3.6 V cell that is 30 mV of margin, so the rail will follow the cell down for most of the discharge. That is fine for a microcontroller and not fine for a radio that needs a clean 3.3 V, which is the case this part is aimed at.

One point five per cent over temperature is the accuracy to budget. It covers the reference drift and the load regulation over the range, and it is the number that appears on a test report. A rail that is also a reference needs a tighter part; a rail that feeds a digital load has margin to spare.

The internal pulldown on the enable pin saves a resistor and a leak. Without it a floating enable on a high impedance pin would sit at an undefined level, and the external resistor used to fix that leaks through the pin when the regulator is on. The internal circuit removes both problems, and it is one of the few features in this class that saves board area as well as current.

The four pin body has no enable, the five pin body does. That is the whole difference between the two smallest packages. A board that switches the rail off needs the five pin SOT-23 on this page. A board that only needs the rail on when the input is present can take the smaller body, and substituting one for the other removes a function.

A one microfarad output capacitor is enough, and a large one is not free. The part is stable from 1 microfarad upwards, but a very large capacitor on a nanoamp regulator takes a long time to charge at power up and produces a slow ramp. On a board that wakes and sleeps, the wake time is part of the budget and the capacitor is part of the wake time.

The addendum prints the package column shifted on this family. Reading the body from the wrong row produces a SOT-23 ordering string with an X2SON package. The suffix is the reliable field: DBV is the five pin SOT-23, DQN is the four pin X2SON, YCH is the die scale body.

This is a 200 mA part and the load has to be counted. A radio that draws 100 mA in transmit plus a microcontroller at 20 mA plus a sensor at 5 mA is already three quarters of the rating, and the transient specification assumes a step to 50 mA rather than to the full current. The headroom is real but not generous.

What to confirm before this part goes on a purchase order

Confirm the fixed voltage and the body. The family covers 0.8 V to 5.0 V across three packages, and two of those packages do not bring the enable pin out.

Ask for the date code and the marking 21PF. Because the parts in this family look identical and differ only in the voltage code, the reel label and the marking are the only check available on a mixed shelf.

The small body and the exposed enable pin are the two fields that decide which reel is the right one for a board that switches its rail.

Where this order code fits

It holds a 3.3 V rail at 200 mA in a thermostat or a fault indicator, where the regulator itself must not be the reason the battery goes flat. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Should I use this or the 25 nanoamp member? Use the 25 nanoamp part when the load sleeps almost all the time and the wake current is small. Use this one when the load steps to tens of milliamp and the rail has to recover quickly, because the faster loop is what stops the step from pulling the rail below the brownout threshold.

Is the output fixed or adjustable? Fixed. The voltage is set at test and cannot be changed on the board, which is why the family covers 0.8 V to 5.0 V in 50 mV steps rather than offering a divider.

What is the minimum input voltage? 1.5 V, and the output needs its dropout on top of that. For a 3.3 V output at full load the input has to be about 3.57 V, so the 1.5 V floor only applies to the lower output options.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.